Home

Roland GK-3 user manual

1. Normal Guitar Cable This connection is necessary not only for playing the guitar s normal straight sound as well as the guitar s straight sound mixed with the synthesizer sound but also for connecting the guitar s ground and the GK 3 s ground Even if you are not going to use the guitar s straight sound at all always make this connection because of the noise reduction benefits it provides How to Connect the GK 3 3 Turn on the power to the connected GK compatible device The Power indicator on the Controller lights up Now when you play your guitar you ll hear the sound of the connected GK compatible device The power indicator lights up when the GK 3 and the GK compatible device are properly connected with a GK cable and the power to the GK compatible device is turned on Always make sure to have the volume level turned down before switching on power Even with the volume all the way down you may still hear some sound when the power is switched on but this is normal and does not indicate a malfunction Before playing be sure to wrap the cable around the guitar strap near the end pin This will prevent the excess strain on the cable that can end up damaging the guitar or the GK 3 19 Specifications GK 3 Divided Pickup Controls Dimensions GK Volume DOWN S1 Switch UP S2 Switch Select Switch Indicator Power Indicator Connecto
2. SWEE LEE MUSIC COMPANY PTE LTD 150 Sims Drive SINGAPORE 387381 TEL 6846 3676 TAIWAN ROLAND TAIWAN ENTERPRISE CO LTD Room 5 9fl No 112 Chung Shan N Road Sec 2 Taipei TAIWAN R O C TEL 02 2561 3339 THAILAND Theera Music Co Ltd 330 Soi Verng NakornKasem New Road Sumpantawongse Bangkok 10100 THAILAND TEL 02 224 8821 VIETNAM SAIGON MUSIC DISTRIBUTOR TAN DINH MUSIC 138 Tran Quang Khai Street Dist 1 Ho Chi Minh City VIETNAM TEL 08 848 4068 AUSTRALIA NEW ZEALAND AUSTRALIA NEW ZEALAND Roland Corporation Australia Pty Ltd 38 Campbell Avenue Dee Why West NSW 2099 AUSTRALIA For Australia Tel 02 9982 8266 For New Zealand Tel 09 3098 715 ARGENTINA Instrumentos Musicales S A Av Santa Fe 2055 1123 Buenos Aires ARGENTINA TEL 011 4508 2700 BARBADOS A amp B Music Supplies LTD 12 Webster Industrial Park Wildey St Michael Barbados TEL 246 430 1100 BRAZIL Roland Brasil Ltda Rua San Jose 780 Sala B Parque Industrial San Jose Cotia Sao Paulo SP BRAZIL TEL 011 4615 5666 CHILE Comercial Fancy II S A Rut 96 919 420 1 Nataniel Cox 739 4th Floor Santiago Centro CHILE TEL 02 688 9540 COLOMBIA Centro Musical Ltda Cra 43 B No 25 A 41 Bododega 9 Medellin Colombia TEL 574 3812529 COSTA RICA JUAN Bansbach Instrumentos Musicales Ave 1 Calle 11 Apartado 10237 San Jose COSTA RICA TEL 258 0211 C
3. pilot holes and the pickup as shown in the figure below then secure the pickup with the screws Wood Screw lt 3 x 20 mm Ge a Pilot Hole i 5 Restring and tune the guitar 5 Adjust the height of the pickup The pickup height should be adjusted so that the distance between the pickup and the strings is about 1 0 mm 0 04 when the highest frets on the first and sixth strings are fingered Check the height using the supplied clearance gauge 1 0 mm Afterwards when connecting to GK compatible devices you will need to adjust the pickup sensitivity again However you may find that the sensitivity level on the GK compatible device is too high In such instances you may be able to correct the problem by widening the clearance between the strings and the pickup so try lowering the Pickup height slightly to see if this approach is effective If the springs are too long use a pair of wire clippers to cut them to the correct size 12 Attaching the GK 3 to the Guitar E Attaching the Pickup with the Pickup Holder 1 Attach the divided pickup to the pickup holder Rubber Sheet Pickup Holder Tighten the screws until the pickup lightly presses down against the rubber sheet Remove the strings and the bridge from the guitar Lower the two bridge height adjustment screws of the guitar approximately 2 mm 0 08 If the bridge is of the type whereby the posts themselves are adjus
4. to the Guitar 4 After removing the pickup carefully If when mounting the divided remove the double sided tape from pickup you find that double sided the bottom of the pickup tape B lacks sufficient adhesion use 5 Adjust the height of the Pickup double sided tape C If you wish to add a spacer first Using double sided tape C strongly and securely completely remove the used double attaches the pickup Note however that once the sided tape from the top surface of pickup is attached with this tape removal from the the existing spacers then add the guitar becomes difficult and may result in damage to the guitar s finish new spacer If you need to remove i any spacers remove the necessary 7 Attach the pickup to the top of the number of spacers and completely spacer that is applied to the guitar side remove the remaining double sided 8 Restring and tune the guitar then tape from the top surface check the height of the Divided 6 Attach two pieces of the new Pickup again double sided tape B to the bottom of Afterwards you will need to adjust the pickup the pickup sensitivity when connecting to GK compatible devices However you may find that the sensitivity level on the GK compatible device is too high In such instances you may be able to correct the problem by widening the clearance between the strings and the pickup Carry out Steps 1 through 8 again to lower the Pickup height slightly How to Use the Cleara
5. to the Guitar Adjusting the Divided Pickup The surface of a guitar s fingerboard is not flat but describes a large arc from the first string to the sixth string and the strings themselves are laid out in roughly the same curved arrangement The divided pickup uses independent coils to pick up the vibrations of each separate string so variations in the clearance between the strings and their corresponding pickups may result in discrepancies in sensitivity for each string The GK 3 s divided pickup features a mechanism that allows you to adjust the curve outlined by the pickups making the GK 3 compatible with different types of guitars 1 Check the curve of the fingerboard on the Be sure not to turn the adjustment screw too much guitar to which the GK 3 is to be attached When raising the yoke rotate the adjustment screw Refer to the guitar manual or catalog or consult the slowly clockwise and stop turning the screw at the guitar manufacturer point where you feel further resistance Continuing to turn the screw beyond this point may result in damage to the unit If you are not sure of your guitar s curve attach the pickup to the guitar with the yokes left in the lowered position then adjust the yokes after the pickup has been installed B Adjust the pickups with the supplied screwdriver When completely extended i e with the adjustment screw turned fully clockwise the yoke is set to approximately 184R when th
6. 92147 PERU Audionet Distribuciones Musicales SAC Juan Fanning 530 Miraflores Lima Peru TEL 511 4461388 TRINIDAD AMR Ltd Ground Floor Maritime Plaza Barataria Trinidad W I TEL 868 638 6385 URUGUAY Todo Musica S A Francisco Acuna de Figueroa 1771 C P 11 800 Montevideo URUGUAY TEL 02 924 2335 VENEZUELA Instrumentos Musicales Allegro C A Av las industrias edf Guitar import 7 zona Industrial de Turumo Caracas Venezuela TEL 212 244 1122 AUSTRIA Roland Elektronische Musikinstrumente HmbH Austrian Office Eduard Bodem Gasse 8 A 6020 Innsbruck AUSTRIA TEL 0512 26 44 260 BELGIUM FRANCE HOLLAND LUXEMBOURG Roland Central Europe N V Houtstraat 3 B 2260 Oevel Westerlo BELGIUM TEL 014 575811 CZECH REP K AUDIO Kardasovska 626 CZ 198 00 Praha 9 CZECH REP TEL 2 666 10529 DENMARK Roland Scandinavia A S Nordhavnsvej 7 Postbox 880 DK 2100 Copenhagen DENMARK TEL 3916 6200 FINLAND Roland Scandinavia As Filial Finland Elannontie 5 FIN 01510 Vantaa FINLAND TEL 0 9 68 24 020 GERMANY Roland Elektronische Musikinstrumente HmbH Oststrasse 96 22844 Norderstedt GERMANY TEL 040 52 60090 GREECE STOLLAS S A Music Sound Light 155 New National Road Patras 26442 GREECE TEL 2610 435400 HUNGARY Roland East Europe Ltd Warehouse Area DEPO Pf 83 H 2046 Torokbalint HUNGARY TEL 23 511011 IRELAND Roland
7. GK 3 are special holders spacers and other accessories which allow you to easily attach the unit to any of a wide variety of guitar models e You can use the controller switches to control the various functions of connected GK devices About the GK 3 Warranty Roland guarantees the GK 3 and all included parts to be free of defects in materials and workmanship Contact your retailer or nearest Roland Service Center if repairs become necessary Roland cannot be responsible for any damage caused to your guitar or the GK 3 as a result of your attempt to install or remove the GK 3 If you are not confident with your ability to properly install the Pickup or Controller unit especially where drilling is involved please contact your Roland retailer or nearest Roland Service Center All product names mentioned in this document are trademarks or registered trademarks of their respective owners Panel Descriptions 6 DOWN S1 Switch 7 UP S2 Switch 8 Power Indicator x 2 GK Volume 3 GK Connector 4 Normal Pickup Input Jack Controller 1 Divided Pickup This pickup detects the vibrations of the guitar strings It is attached between the guitar bridge and the bridge pickup 2 GK Volume This controls the volume of the connected GK compatible device Certain GK compatible devices also permit the GK Volume function to be changed For more detailed information refer to the Owner s M
8. Ireland G2 Calmount Park Calmount Avenue Dublin 12 Republic of IRELAND TEL 01 4294444 ITALY Roland Italy S p A Viale delle Industrie 8 20020 Arese Milano ITALY TEL 02 937 78300 NORWAY Roland Scandinavia Avd Kontor Norge Lilleakerveien 2 Postboks 95 Lilleaker N 0216 Oslo NORWAY TEL 2273 0074 POLAND MX MUSIC SP Z 0 0 UL Gibraltarska 4 PL 03664 Warszawa POLAND TEL 022 679 44 19 PORTUGAL Roland Iberia S L Portugal Office Cais das Pedras 8 9 1 Dto 4050 465 Porto PORTUGAL TEL 22 608 00 60 ROMANIA FBS LINES Piata Libertatii 1 535500 Gheorgheni ROMANIA TEL 266 364 609 RUSSIA MuTek Dorozhnaya ul 3 korp 6 117 545 Moscow RUSSIA TEL 095 981 4967 SPAIN Roland Iberia S L Paseo Garc a Faria 33 35 08005 Barcelona SPAIN TEL 93 493 91 00 SWEDEN Roland Scandinavia A S SWEDISH SALES OFFICE Danvik Center 28 2 tr 131 30 Nacka SWEDEN TEL 0 8 702 00 20 SWITZERLAND Roland Switzerland AG Landstrasse 5 Postfach CH 4452 Itingen SWITZERLAND TEL 061 927 8383 UKRAINE TIC TAC Mira Str 19 108 P O Box 180 295400 Munkachevo UKRAINE TEL 03131 414 40 UNITED KINGDOM Roland U K Ltd Atlantic Close Swansea Enterprise Park SWANSEA SA7 9FJ UNITED KINGDOM TEL 01792 702701 MIDDLE EAST BAHRAIN Moon Stores No 16 Bab Al Bahrain Avenue P O Box 247 Manama 304 State of BAHRAIN TEL 17 211 005 CYPRUS Radex Sound Equip
9. Roland DIVIDED PICKUP DK Owner s Manual Thank you for purchasing the Roland GK 3 divided pickup Before using this unit carefully read the sections entitled e USING THE UNIT SAFELY page 2 3 e IMPORTANT NOTES page 3 These sections provide important information concerning the proper operation of the unit Additionally in order to feel assured that you have gained a good grasp of every feature provided by your new unit Owner s manual should be read in its entirety The manual should be saved and kept on hand as a convenient reference Copyright 2003 Roland CORPORATION All rights reserved No part of this publication may be reproduced in any form without the written permission of Roland CORPORATION oE a B26 B B E 2 TE zZs dn Sawe NN Roland P gt GK 3 USING THE UNIT SAFELY INSTRUCTIONS FOR THE PREVENTION OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS About Z WARNING and Z CAUTION Notices About the Symbols Used for instructions intende the user to the risk of death injury should the unit improperly Z WARNING to alert or severe be used Used for instructions intende the user to the risk of injury o damage should the unit improperly CAUTION respect to the home an furnishings as well to animals or pets to alert r material e used Material damage refers to damage or ot
10. Shanghai Electronics Co Ltd 5F No 1500 Pingliang Road Shanghai 200090 CHINA TEL 021 5580 0800 Roland Shanghai Electronics Co Ltd BEIJING OFFICE 10F No 18 3 Section Anhuaxili Chaoyang District Beijing 100011 CHINA TEL 010 6426 5050 Roland Shanghai Electronics Co Ltd GUANGZHOU OFFICE 2 F No 30 Si You Nan Er Jie Yi Xiang Wu Yang Xin Cheng Guangzhou 510600 CHINA TEL 020 8736 0428 HONG KONG Tom Lee Music Co Ltd Service Division 22 32 Pun Shan Street Tsuen Wan New Territories HONG KONG TEL 2415 0911 Parsons Music Ltd 8th Floor Railway Plaza 39 Chatham Road South T S T Kowloon HONG KONG TEL 2333 1863 INDIA Rivera Digitec India Pvt Ltd 409 Nirman Kendra Mahalaxmi Flats Compound Off Dr Edwin Moses Road Mumbai 400011 INDIA TEL 022 2493 9051 INDONESIA PT Citra IntiRama J1 Cideng Timur No 15 150 Jakarta Pusat INDONESIA TEL 021 6324170 KOREA Cosmos Corporation 1461 9 Seocho Dong Seocho Ku Seoul KOREA TEL 02 3486 8855 MALAYSIA Roland Asia Pacific Sdn Bhd 45 1 Block C2 Jalan PJU 1 39 Dataran Prima 47301 Petaling Jaya Selangor MALAYSIA TEL 03 7805 3263 When you need repair service call your nearest Roland Service Center or authorized Roland distributor in your country as shown below PHILIPPINES G A Yupangco amp Co Inc 339 Gil J Puyat Avenue Makati Metro Manila 1200 PHILIPPINES TEL 02 899 9801 SINGAPORE
11. URACAO Zeelandia Music Center Inc Orionweg 30 Curacao Netherland Antilles TEL 305 5926866 DOMINICAN REPUBLIC Instrumentos Fernando Giraldez Calle Proyecto Central No 3 Ens La Esperilla Santo Domingo Dominican Republic TEL 809 683 0305 ECUADOR Mas Musika Rumichaca 822 y Zaruma Guayaquil Ecuador TEL 593 4 2302364 EL SALVADOR OMNI MUSIC 75 Avenida Norte y Final Alameda Juan Pablo II Edificio No 4010 San Salvador EL SALVADOR TEL 262 0788 GUATEMALA Casa Instrumental Calzada Roosevelt 34 01 zona 11 Ciudad de Guatemala Guatemala TEL 502 599 2888 HONDURAS Almacen Pajaro Azul S A de C V BO Paz Barahona 3 Ave 11 Calle S O San Pedro Sula Honduras TEL 504 553 2029 MARTINIQUE Musique amp Son Z 1 Les Mangle 97232 Le Lamantin Martinique F W 1 TEL 596 596 426860 Gigamusic SARL 10 Rte De La Folie 97200 Fort De France Martinique F W I TEL 596 596 715222 MEXICO Casa Veerkamp s a de c v Av Toluca No 323 Col Olivar de los Padres 01780 Mexico D F MEXICO TEL 55 5668 6699 NICARAGUA Bansbach Instrumentos Musicales Nicaragua Altamira D Este Calle Principal de la Farmacia 5ta Avenida 1 Cuadra al Lago 503 Managua Nicaragua TEL 505 277 2557 PANAMA SUPRO MUNDIAL S A Boulevard Andrews Albrook Panama City REP DE PANAMA TEL 315 0101 PARAGUAY Distribuidora De Instrumentos Musicales J E Olear y ESQ Manduvira Asuncion PARAGUAY TEL 595 21 4
12. allation make sure to put them in a safe place out of children s reach so there is no chance of them being swallowed accidentally IMPORTANT NOTES In addition to the items listed under USING THE UNIT SAFELY please read and observe the following Power Supply Before connecting this unit to other devices turn off the power to all units This will help prevent malfunc tions and or damage to speakers or other devices Placement e Using the unit near power amplifiers or other equipment containing large power transformers may induce hum To alleviate the problem change the orientation of this unit or move it farther away from the source of interference e Noise may be produced if wireless communications devices such as cell phones are operated in the vicinity of this unit Such noise could occur when receiving or initiating a call or while conversing Should you experience such problems you should relocate such wireless devices so they are at a greater distance from this unit or switch them off e Do not expose the unit to direct sunlight place it near devices that radiate heat leave it inside an enclosed vehicle or otherwise subject it to temper ature extremes Excessive heat can deform or discolor the unit e When moved from one location to another where the temperature and or humidity is very different water droplets condensation may form inside the unit Damage or malfunction may result if you
13. anual for the GK compatible device being connected 3 GK Connector Connect the GK compatible device to this connector 4 Normal Pickup Input Jack This jack is for inputting the guitar s normal pickup signals to the GK 3 Connect using the normal guitar cable included with the GK 3 O gt Pickup Cable R Adjustment Screw 1 Divided Pickup Pickup 5 Select Switch This switches between the output from the connected GK compatible device and the normal guitar output Changing the GK Volume function also changes the function of this switch For more detailed information refer to the Owner s Manual for the GK compatible device being connected 6 DOWN S1 Switch 7 UP S2 Switch The function of the S1 and S2 switches varies according to the GK compatible device connected For more detailed information refer to the Owner s Manual for the GK compatible device being connected 8 Power Indicator This indicates that power is being supplied to the GK 3 Power to the GK 3 is supplied by the connected GK compatible device via the GK cable No battery or other power source is required Attaching the GK 3 to the Guitar The GK 3 can be attached to and used with conventional electric and acoustic guitars Please read the following precautions before installing the GK 3 Precautions Before Installing Do not use the GK 3 with 12 string e If only the double sided tape is used to gui
14. attempt to use the unit in this condition Therefore before using the unit you must allow it to stand for several hours until the condensation has completely evaporated Maintenance e For everyday cleaning wipe the unit with a soft dry cloth or one that has been slightly dampened with water To remove stubborn dirt use a cloth impreg nated with a mild non abrasive detergent After wards be sure to wipe the unit thoroughly with a soft dry cloth e Never use benzine thinners alcohol or solvents of any kind to avoid the possibility of discoloration and or deformation Additional Precautions e Use a reasonable amount of care when using the unit s buttons sliders or other controls and when using its jacks and connectors Rough handling can lead to malfunctions e When connecting disconnecting all cables grasp the connector itself never pull on the cable This way you will avoid causing shorts or damage to the cable s internal elements To avoid disturbing your neighbors try to keep the unit s volume at reasonable levels You may prefer to use headphones so you do not need to be concerned about those around you especially when it is late at night e When you need to transport the unit package it in the box including padding that it came in if possible Otherwise you will need to use equiv alent packaging materials e Use a cable from Roland to make the connection If using some other make of co
15. e yoke is in the fully lowered position the setting is approximately 400R R Adjustment Screw If the guitar has a fingerboard curve with a value such as 250R or 300R first adjust the yoke so that the yoke height is approximately midway between the fully extended and lowered positions then adjust to the optimal positions after the pickup is installed Attaching the GK 3 to the Guitar Attaching the Divided Pickup There are three ways to attach the divided pickup Attaching the Pickup with Double Sided Tape p 9 This provides the simplest way to attach the pickup to flat top guitars Attaching the Pickup with Screws p 12 This method features the benefit of allowing the pickups to be finely adjusted later on but it is somewhat difficult to carry out Attaching the Pickup with the Pickup Holder p 13 This is the simplest method for guitars with the bridge mounted on posts embedded in the guitar body Do not place any unnecessary strain on the cable connecting the pickup and the controller This may result in breaking Do not bend or twist the pickup Use particular care when removing the pickup E Attaching the Pickup with Double Sided Tape 1 Place the pickup between the guitar s body and strings and determine the position for attachment In principle the pickup should be centered with respect to the six strings as close to the bridge as possible If your guitar has a tr
16. emolo unit whammy bar then attaching the pickup at the bridge position may bring the pickup into direct contact with the tremolo unit Position the pickup so that it will not interfere with operation of the tremolo unit Attach the pickup about 15 mm 9 16 from the bridge if your guitar is strung with copper brass or bronze wound strings such as with an acoustic guitar Regardless of the guitar do not position the divided pickup more than 20 mm 13 16 from the bridge Maximum 20 mm When viewed from the front the strings do not necessarily need to be aligned perfectly with the center of the yokes Each string need only pass over some portion of its yoke e i Li Forth String ii Fifth String i Sixth String Be sure the divided pickup is correctly oriented The cord from the pickup should emerge from under the sixth string When you have determined the position in which the pickup is to be attached mark the position with a pencil cellophane tape or other appropriate marking 2 Be sure the neck curvature and string height are set properly then tune each string to its normal tuning 9 Attaching the GK 3 to the Guitar Changes in the string height following installation of the GK 3 pickup may cause the clearance between the strings and the pickup to change which can result in poorer sensitivity Adjust the height of the pickup I
17. evices always turn down the volume and turn off the When connection cables with resistors are used the volume level of equipment connected to the inputs Normal Pickup Input jack may be low If this happens use connection cables that do not contain resistors such as those from the Roland PCS series When all devices are properly connected turn on the power to the various devices in the order specified below Turning on devices in the wrong order may result in malfunction and or damage to speakers and other devices 1 Make sure that the power to the GK compatible device being connected is turned off then connect the device to the GK 3 s GK connector using the GK cable i GK cable a GK compatible device Connect the GK 3 only with OTE dedicated GK cable supplied with Roland GK compatible devices and optional GK cables sold by Roland Use of any other cable may result in damage or malfunction The GK cable is a locking cable When disconnecting the cable do not pull on it with undue force but instead release the lock and gently disconnect the cable You can disconnect the cable simply and easily by holding down the locking portion with your thumb and gently pulling on the plug 2 Use the included Normal guitar cable to connect the output jack on the guitar to the GK 3 s Normal Pickup input jack
18. from the 4 Attach holder B so that the guitar underside of the controller then attach body is sandwiched between the two the GK 3 to holder A holders Holder A i Cap Nut Je 7 Holder B Flat Washer Spring Washer 5 Tighten holders A and B using the flat washer the spring washer and the cap nut When attaching the GK 3 to an arched top guitar place the cushion between the guitar and holder y 2 Loosen the guitar s end pin and insert holder A Guitar Body Cap Nut 3 Screw in the end pin 16 Attaching the GK 3 to the Guitar E Attaching with Double sided Tape and a Screw 1 Place the controller in an appropriate position on the guitar surface to determine where it is to be attached Pay attention to the following points at this time e Install on a level surface e Position the controller so it does not interfere with your playing e If your guitar includes a fine tuning control position the controller so it does not interfere with operation of the fine tuning e Position the controller so you can comfortably operate the select switch the S1 and S2 switches and other controls e Position the controller so that it does not place undue strain on the Normal Pickup Input jack divided pickup or GK connector cables Make sure that the plugs connected to the GK connecto
19. her adverse effects caused with all its domestic A The A symbol alerts the user to important instructions or warnings The specific meaning of the symbol is determined by the design contained within the triangle In the case of the symbol at left it is used for general cautions warnings or alerts to danger The symbol alerts the user to items that must never be carried out are forbidden The specific thing that must not be done is indicated by the design contained within the circle In the case of the symbol at left it means that the unit must never be disassembled Before using this unit make sure to read the instructions below and the Owner s Manual Do not open or perform any internal modifications on the unit A Do not attempt to repair the unit or replace parts within it except when this manual provides specific instructions directing you to do so Refer all servicing to your retailer the nearest Roland Service Center or an authorized Roland distributor as listed on the Information page Never use or store the unit in places that are Subject to temperature extremes e g direct sunlight in an enclosed vehicle near a heating duct on top of heat generating equipment or are e Damp e g baths washrooms on wet floors or are e Humid or are e Exposed to rain or are e Dusty or are e Subject to high levels of vibration The symbol a
20. lerts the user to things that must be carried out The specific thing that must be done is indicated by the design contained within the circle In the case of the symbol at left it means that the power cord plug must be unplugged from the outlet ALWAYS OBSERVE THE FOLLOWING Do not allow any objects e g flammable material coins pins or liquids of any kind water soft drinks etc to penetrate the unit Immediately turn the power off and request servicing by your retailer the nearest Roland Service Center or an authorized Roland distributor as listed on the Information page when e If smoke or unusual odor occurs Objects have fallen into or liquid has been spilled onto the unit or e The unit has been exposed to rain or otherwise has become wet or e The unit does not appear to operate normally or exhibits a marked change in performance In households with small children an adult should provide supervision until the child is capable of following all the rules essential for the safe operation of the unit Protect the unit from strong impact Do not drop it e Try to prevent cords and cables from becoming entangled Also all cords and cables should be placed so they are out of the reach of children e Never climb on top of nor place heavy objects on the unit e Disconnect all cords coming from external devices before moving the unit e Should you remove the parts of inst
21. m for the divided pickup consult your guitar dealer Attaching the GK 3 to the Guitar Confirm that the package contains all of the following parts for installing the GK 3 Flat head Screw 3x16 mm Pickup Cushion Cushion x 1 for installing x4 he Controller for installing the Divided Pickup Wood Screw 3x20 mm x 2 for attaching i Pickup Spacer A Cap Nut the Holder A x 2 for installing he Divided Pickup x1 for attaching the Holder B Sprin x2 pring for adjusting the height of Spring Washer the Divided Pickup x 2 for installing oe xi bs ae he Divided Pickup e Holder B Double sided tape A x 3 for installing the Controller Double sided tape B lt x 4 for installing the Divided Pickup Double sided tape C Holder A x 2 for installing the Divided Pickup Pickup Spacer B x3 for adjusting the height of the Divided Pickup Pickup Spacer C x4 for adjusting the height of the Divided Pickup Normal Guitar Cable Flat Washer 15 mm x1 for attaching the Holder B Pickup Holder for attaching he Divided Pickup to he Pickup Holder Rubber Tube 9 x2 for attaching he Divided Pickup to he Pickup Holder Screw 3x8 mm x2 for attaching he Divided Pickup to he Pickup Holder Flat Washer 13 mm x2 for attaching the Pickup Holder to the guitar Screwdriver A E 1 Attaching the GK 3
22. ment Ltd 17 Diagorou Street Nicosia CYPRUS TEL 022 66 9426 IRAN MOCOINC No 41 Nike St DrShariyati Ave Roberoye Cerahe Mirdamad Tehran IRAN TEL 021 285 4169 ISRAEL Halilit P Greenspoon amp Sons Ltd 8 Retzif Ha aliya Hashnya St Tel Aviv Yafo ISRAEL TEL 03 6823666 JORDAN MUSIC HOUSE CO LTD FREDDY FOR MUSIC P O Box 922846 Amman 11192 JORDAN TEL 06 5692696 KUWAIT EASA HUSAIN AL YOUSIFI amp SONS CO Abdullah Salem Street Safat KUWAIT TEL 243 6399 LEBANON Chahine S A L Gerge Zeidan St Chahine Bldg Achrafieh P O Box 16 5857 Beirut LEBANON TEL 01 20 1441 OMAN TALENTZ CENTRE L L C Malatan House No 1 Al Noor Street Ruwi SULTANATE OF OMAN TEL 2478 3443 QATAR Al Emadi Co Badie Studio amp Stores P O Box 62 Doha QATAR TEL 4423 554 SAUDI ARABIA aDawliah Universal Electronics APL Corniche Road Aldossary Bldg Ist Floor Alkhobar SAUDI ARABIA P O Box 2154 Alkhobar 31952 SAUDI ARABIA TEL 03 898 2081 SYRIA Technical Light amp Sound Center Rawda Abdul Qader Jazairi St Bldg No 21 P O BOX 13520 Damascus SYRIA TEL 011 223 5384 TURKEY ZUHAL DIS TICARET A S Galip Dede Cad No 37 Beyoglu Istanbul TURKEY TEL 0212 249 85 10 U A E Zak Electronics amp Musical Instruments Co L L C Zabeel Road Al Sherooq Bldg No 14 Grand Floor Dubai U A E TEL 04 3360715 NORTH AMERICA CANADA R
23. n the pickup spacers and the pickup and carefully attach the pickup to the guitar Although double sided tape B is used for the pickup if the adhesive capability seems insufficient after installation use double sided tape C instead Using double sided tape C strongly and securely attaches the pickup Note however that once the pickup is attached with this tape removal from the guitar becomes difficult and may result in damage to the guitar s finish Restring and tune the guitar then carefully check the height of the divided pickup once more Measure with the clearance gauge to confirm that the clearances between the pickup and the strings are approximately 1 0 mm 0 04 when you press the first and sixth strings at the highest fret play the strings and confirm that the strings do not come into contact with the pickup Take the steps below if the height of the divided pickup is not right 1 Carefully examine the pickup in its current state and add a suitable number of spacers if the pickup is too low or remove one or more spacers if the pickup is too high 2 Remove the strings from the guitar 3 Remove the divided pickup from the guitar Use care in handling the divided pickup bending or twisting it may cause breaking in the coil elements Carefully insert something thin and flat like a table knife under the Pickup from the sixth string side then gently pry the pickup upwards 10 Attaching the GK 3
24. nce Gauge The divided pickup height must be adjusted so that the clearance between each string and the divided pickup is 1 0 mm 0 04 when the highest fret is fingered The clearance gauge supplied with the GK 3 is 1 0 mm thick place the gauge between the strings and the divided pickup as shown in the figure below then check and adjust the height Attaching the GK 3 to the Guitar E Attaching the Pickup with Screws The steps for determining the position for attaching the pickup and for checking the height are exactly the same as when using the double sided tape Refer to Attaching the Pickup with Double Sided Tape p 9 The height of the strings from the body must be no less than 13 mm 9 16 when the pickup is attached with screws Determine the position for attaching the pickup When you have determined the positioning mark the position of the holes at each end of the pickup on the guitar s body Remove the strings from the guitar Using a drill or similar means open pilot holes where the attachment screws are to go in If the pilot holes are not made in the correct positions then the pickup will not be attached in the correct position either Use extra care when drilling the pilot holes Make the pilot holes approximately 2 mm 0 08 in diameter Drill pilot holes slightly more than 2 mm in diameter if the guitar body is made of a particularly hard material Place the springs between the
25. nnection cable please note the following precautions e Some connection cables contain resistors Do not use cables that incorporate resistors for connecting to this unit The use of such cables can cause the sound level to be extremely low or impossible to hear For information on cable specifications contact the manufacturer of the cable Contents Main Features USING THE UNIT SAFELY 2 IMPORTANT NOTES 3 Panel Descriptions 5 Attaching the GK 3 to the Guitar 6 Precautions Before Installing 6 Adjusting the Divided Pickup 8 Attaching the Divided Pickup 9 Attaching the Pickup with Double Sided Tape 9 Attaching the Pickup with Screws ccccsececeee 12 Attaching the Pickup with the Pickup Holder 13 Checking and Finely Adjusting the Pickup Height 14 Attaching the Controller 15 Adjusting the Length of the Pickup Cable 15 Attaching with the Holder 16 Attaching with Double sided Tape and a Screw 17 How to Connect the GK 3 18 Specifications 20 The GK 3 is a special divided pickup which when installed on an ordinary guitar allows you to use the guitar to play the sounds of GK compatible guitar devices Roland GR 20 or VG 88 etc e The pickup s adjustable curve mechanism makes the GK 3 compatible with guitars with different fingerboard string curves e Included with the
26. nsert the supplied spacers under the pickup until it is at the required height do not yet remove the protective paper backing from the spacer s double sided tape There are three types of pickup spacers A 3 mm B 1 mm and C 0 25 mm combine these as necessary to achieve the proper pickup height The pickup height should be adjusted so that the distance between the pickup and the strings is about 1 0 mm 0 04 when the highest frets on the first and sixth strings are fingered Check the height using the supplied clearance gauge 1 0 mm and adjust the height as necessary p 11 If the first and sixth string heights differ greatly when the highest fret is fingered compensate by adding the appropriate half width or one third width spacers until the clearance for both strings is the same When using an arch top guitar put the pickup cushions under the pickup spacers Adjust the pickup cushion thickness as required for example by using two pickup cushions The pickup spacers and the pickup cushions are attached to the guitar with double sided tape When affixing the tape however the tape s thickness is reduced by 0 1 mm 0 004 when the backing of the tape is removed Therefore when using several pickup spacers take this fact into account and set the height slightly higher to compensate 4 5 Remove the strings from your guitar Remove the backing from the tapes for the pickup cushio
27. oland Canada Music Ltd Head Office 5480 Parkwood Way Richmond B C V6V 2M4 CANADA TEL 604 270 6626 Roland Canada Music Ltd Toronto Office 170 Admiral Boulevard Mississauga On L5T 2N6 CANADA TEL 905 362 9707 U S A Roland Corporation U S 5100 S Eastern Avenue Los Angeles CA 90040 2938 U S A TEL 323 890 3700 As of December 10 2005 ROLAND Roland Corporation
28. r and Normal Pickup Input jack do not stick out as this may result in damage should undue strain be placed on the GK connector or Normal Pickup Input jack 2 Once the controller position has been determined place the controller in position and carefully drill a pilot hole in the guitar body where the controller s attachment hole is located The diameter of the hole should be about 2 mm 0 08 inches Confirm that there are no other problems in attaching the controller before drilling the pilot hole 3 After attaching the double sided tape A to the underside of the Controller attach the controller to the guitar 4 Secure the controller with the supplied screw flat head 3x16 mm A Ye Put the screw flat head 3x16 mm through this hole If you d rather not drill a hole in your guitar you can secure the Controller using only the double sided tape or the holders However if only the double sided tape is used to secure the unit shocks from rough handling during performances and from use over an extended period will cause the tape to deteriorate with the GK 3 shifting out of position as a result Furthermore if the finish on your guitar is less than perfect you may discover that the finish is also removed when you later remove the tape 17 How to Connect the GK 3 power on all devices before making any connections To prevent malfunction and or damage to speakers or other d
29. rs GK Connector Normal Pickup Input Jack Weight 60g 30z J Accessories Normal Guitar Cable Parts for installation Owner s Manual Unit mm inch Options GK Cables GKC 3 GKC 5 GKC 10 GK Parallel Box GKP 4 Unit Selector US 20 102 3 4 1 16 7 8 5 16 CSS SST In the interest of product development the specifications and or appearance of this unit are S 588S subject to change without prior notice o ol co D r with yokes at maximum height Unit mm inch CO n225 For EU Countries C This product complies with the requirements of European Directive 89 336 EEC This product must be disposed of separately at your local waste recycling centre mm DO not dispose of in household waste bin 20 Information EGYPT Al Fanny Trading Office 9 EBN Hagar A1 Askalany Street ARD El Golf Heliopolis Cairo 11341 EGYPT TEL 20 2 417 1828 REUNION Maison FO YAM Marcel 25 Rue Jules Hermann Chaudron BP79 97 491 Ste Clotilde Cedex REUNION ISLAND TEL 0262 218 429 SOUTH AFRICA That Other Music Shop PTY Ltd 11 Melle St Braamfontein Johannesbourg SOUTH AFRICA TEL 011 403 4105 FAX 011 403 1234 Paul Bothner PTY Ltd Royal Cape Park Unit 24 Londonderry Road Ottery 7800 Cape Town SOUTH AFRICA TEL 021 799 4900 CHINA Roland
30. tars or guitars with other unusual or customized string setups guitars strung with non metal core nylon strings The unit will not function properly with these instruments Make any adjustments to the guitar neck string height and other such modifications before installing the GK 3 Try placing the divided pickup and the controller unit on the guitar before actually attaching them to confirm that there will be no problem with the installation When using the screw to attach the controller we recommend that you first attach the GK 3 temporarily using the holder then after confirming that there are no problems when actually performing with the unit secure it with the screw attach the controller shocks from rough handling during performances and from extended use will cause the tape to deteriorate with the controller shifting out of position as a result Also if the finish on your guitar is less than perfect you may discover that the finish is also removed when you later remove the tape The supplied tape is intended to be used only very temporarily to help you determine the optimum position for the controller With certain guitars the space between the pickup at the bridge position and the bridge itself is too narrow to allow installation of the divided pickup In such instances it may be possible to attach the pickup by modifying the guitar for example by moving the bridge pickup more towards the neck to make roo
31. ted then lower the post height by 2 mm 0 08 Place the holder on the posts then cover it with the bridge Neck side lt Bridge Pickup Holder Bridge Height lt _ Adjustment Screw of the Guitar Restring and tune the guitar Tune the strings with the divided pickup adjusted to the optimal position where all strings ride over their respective yokes 6 Adjust the height of the pickup The pickup height should be adjusted so that the distance between the pickup and the strings is about 1 0 mm 0 04 when the highest frets on the first and sixth strings are fingered Check the height using the supplied clearance gauge 1 0 mm If the pickup ends up being too low use two rubber sheets layered together But the pickup still sits too low even after layering the two rubber sheets then use the rubber tubes Rubber Tube Pickup Holder If the pickup position is too high insert the included 13 mm washers between the pickup holder and the bridge Neck side Z Bridge Washer 013 mm Pickup Holder Bridge Height 2 we Adjustment eae A Screw of nd pin side Uy the Guitar Post gt Afterwards when connecting to GK compatible devices you will need to adjust the pickup sensitivity again However you may find that the sensitivity level on the GK compatible device is too high In such instances you may be able to correct the problem by widening
32. the clearance between the strings and the pickup so try lowering the Pickup height slightly to see if this approach is effective 13 Attaching the GK 3 to the Guitar Checking and Finely Adjusting the Pickup Height Use the clearance gauge to confirm that the clearance between each string and the pickup is about 1 mm If the gap is greater than 1 mm 0 04 make fine adjustments to the height of the pickup itself and to the pickup curve refer to p 8 Attaching the GK 3 to the Guitar Attaching the Controller There are two ways to attach the controller Attaching the Controller Unit with Attaching the Controller Unit with Holder p 16 Double Sided Tape and Screws p 17 With this method the holder is secured This allows you to position the controller using the guitar s strap pin This permits where you like on the guitar and by not easy installation with no modification of the using the holder reduce the thickness of the guitar required controller However attaching the controller with the tape and screw is difficult to do with arched top guitars E Adjusting the Length of the Pickup Cable Place the controller where it is actually to be attached to the guitar to check the pickup cable length If the cable is too long wind it up in the space behind the controller 15 Attaching the GK 3 to the Guitar E Attaching with the Holder 1 Remove three screws

Roland GK-3 user manual

Contents

Download Pdf Manuals

Related Search

Related Contents