PanasonicWV-7260 MV-7360 Manual
Contents
1. Focus me Dem poe OPEN 6V DC Iris CLOSE 6V DC Less than 100mA Note a When using a lens with a built in auto iris control circuit It is unnecessary to connect the iris line Terminal No 11 b When using lens without a built in auto iris control circuit If auto iris is desired be sure to use the Remote Control Unit WV 7460 and the Relay Box WV 7465 which has an auto iris circuit inside It is impossible to use the Remote Control Unit WV 7360 which has no auto iris circuit inside B Video Terminal Board 1 Wiring precautions e Do not bend coaxial cable into a curve whose radius is smaller than 10 times diameter Never staple the cable not even with circular staples Never crush or pinch the cable Alt these will change the impedance of the cable and cause poor picture quality 2 Use 752 cable RG 59 RG 59A U RG 59B U RG 59 U RG 6 U RG 11 U 3 Wiring Prepare coaxial cable as shown as below fold back 3 8 1 8 1 10mm 3mm 25mm 4 Wiring between WV 7260 and WV 7360 Clamp the cable with cable clamps and connect one wire to each terminals If 9 or 15 conductor cable is used connect the 9th or 15th wire to terminal 9 which doubles the common return tine of 24V AC line A multi conductor cable is not provided Pan Tilt Head Remote Control Unit WV 7260 WV 7360 EET 1 LEFT NE Sur RIGHT 3 o RIGHT UP 3 olup TILT2. Tilt Limit Stop Adjustable tilting angle Up 0 15 Down 0 60 See page 7 Control Cable 9 25 7 16 700mm Long See page 5 and 8 Pan Limit Stop Adjustable panning angle 10 340 See page 7 Mounting Holes 4 3 8 4 99 See page 4 Wire Hole Hole for wiring Terminal Strip CL gl See page 4 5 and 8 Cable Clamp e Remote Control Unit WV 7360 Front View Rear View Pitot Lamp Pan Tilt Control RIGHT LEFT UP DOWN Zoom Control ZOOM TELE WIDE Focus Control FOCUS NEAR FAR tris Control IRIS OPEN CLOSE Terminal Strip Defroster Control DEFROSTER ON OFF Wiper Control WIPER ON OFF Power Cord Camera Control CAMERA ON OFF 6 feet 1 8m ON OFF Switch POWER ON OFF INSTALLATION e Select a flat surface capable of supporting the combined weight of Pan Tilt Head Camera Housing Camera and Lens 1 The Pan Tilt Head must be securely fastened with four hex head bolts not provided using four Mounting Holes 4 63 8 4 9mm CONNECTIONS A Terminal Strip e Remove the cover and complete the wiring Cautions Keep the power switch OFF during installation Do not cause a short between terminals This will cause a fuse to blow 1 Direct control with Camera Housing WV 7150 Select a multi conductor cable with 8 or 9 conductors The wire gauge can be determined by the Table 1 The wire should meet FR 1
3. Pan Tilt Head amp Remote Control Unit a 1 i a n in L n ii age n T u ro wu Lu LL i i U h k rH i i ki te IE Al i Ii i E In n ne L r U Hn ia n i r z 1 I I ie 1 a J s A T i r T 3 u k i 6 I 1 F U Fi ks IL iL T E 1M F i 1 c I z o 1 I r i 1 i H Pa E a a ine ae ontrol Unit Lh 1 m i y TH i 1 FEN 1 U iF n ri A 1 I ry ML T Mr oor iA sad QU DU Ar W ue de dE ox Wc E QE MN I uid E cw ub W d X mW o4 ik t T Ia E m ae LN iir tr ns se cee MI A May d M Ee GE l WV 3 S2 ot ow ck of oW Wt oou If E M s zb o l r ED He u vat EL v U t A Ta u 3 ie 4 u vE id Ale o H U D H Ti Pa E i MM n Fr E I Panasonic Before attempting to connect or operate this product please read these instructions completely CONTENTS Page LT RO OC ON ual diia ro RE ne he qna ta a OR RE aw JE ORG So See ae ate deca dee Bd 1 PRECAUTIONS cei 6 du adr e icu Be ieee a a ewe ee ee eS we a RN SCR RU Seda 2 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS 3 INSTALLATION 4 a6 op ee NE Ale VERE ale wie EN SERE RD e ALIS SPMS org nade Go ee 4 CONNECTIONS s 5 2 36372 Si oot eta d s eo En Hato c AC Be EA OE E ee Se 4 OPERATION i aaura CER eee ees OE es pP Eee Eier E s partu eee 6 BDIJUSIMEN LES cu 6 4200 9 RC HR eo i Or ACCRUE EXC E e E ECC ee etu bb DR d 7 TYPICAL SYSTEM CONNECTIONS leere ie ee ee ie ee r
4. Hex Head Bolt Part No XVG8C20V 6 pcs 3 Amp 125v AC Stow Blow Plain Washer Part No XWA8BV 6 pcs Part No YWST6 3A Tn 1 pc Lock Washer Part No XWG8V 6 pcs 5 Amp 125V AC Solw Blow Part No YNST6 bA 0 cc cee rn 1 pc OPTIONAL ACCESSORIES Rack Mount Flame WJ A01 WJ 802 SCHEMATIC DIAGRAM Outdoor Camera Housing e y a 0 indie BR mm SS Ts a e Pan Tilt Head Remote Control Unit WV 7260 J WV 7360 m M M O TT o A e oto ae T E imi 1 LEFT o o 2 RIGHT Ust a l ue js o 4o 4 l oowN peace ie eoi do gt 6 HOUSING a o 7 DEFROSTER le 8 WIPER m zi pes e Bt b els5 Et o 10 DC coM j60Hz Hz WHT onl ms Ne p 01211 Focus l5 VIE 01311 zoom ej Sur 14 GRN TB1 GND OUTLINE DRAWING e Pan Tilt Head WV 7260 4 3 4 4 23 8 4 29 5 13 16 276 ss 6 5 16 m 160 13 16 176 e Remote Control Unit WV 7360 3 13 16 5 3 4 8 3 8 210 6 11 16 PANASONIC COMPANY Division of Matsushita Electric Corporation of America Executive Office One Panasonic Way Secaucus New Jersey 07094 201 348 7000 Video Systems Division Executive Office One Panasonic Way Secaucus New Jersey 07094 201 348 7000 Eastern Regional
5. Office Panasonic Video Systems 50 Meadowlands Parkway Secaucus New Jersey 07094 201 348 7627 Midwest Regional Office Panasonic Video Systems 1098 Greenleaf Avenue Elk Grove Village Illinois 60007 312 593 0710 Southeast Regional Office Panasonic Video Systems Two Meca Way Duluth Georgia 30136 404 448 5683 Southwest Regional Office Panasonic Video Systems 1825 Walnut Hill Lane Irving Texas 75062 214 258 2828 Western Sales Office Newcraft Inc 8383 Wilshire Btvd Beverty Hills California 90211 213 655 1111 Matsushita Electric of Hawaii Inc 320 Waiakamilo Road Honolulu Hawaii 96817 B0B 847 5361 Matsushita Electric of Canada Limited 40 Ronson Drive Rexdale Ontario M9W 185 Canada 416 248 5551 Panasonic Sales Company Ave 65 de infanteria K m 9 7 Victoria Industrial Park Carolina Puerto Rico 00630 809 769 4320 ex dd uus NO0777 0 24 15 16 15 16 70 24 70 YWV7260PRB1
6. t TILT DOWN 4 o DOWN CAMERA 24V AC 5 o CAMERA 24V AC HOUSING HOUSING FAN HEATER FAN HEATER DEFROSTER o DEFROSTER FOCUS ZOOM GND O it is unnecessary to connect No 7 No 8 No 10 No 11 No 12 and No 13 when using the Camera Housing WV 7150 Connect as follows 1 Clamp the coaxial cable with Cable Clamp 2 Hold the shield wire 3 Connect the inner conductor C Power Cord WV 7360 1 Keep the Power switched OFF during installation 2 Connect the Power Cord to a 60Hz grounded electrical outlet 108V AC to 132V AC preferably 120V AC After all connections replace the cover OPERATION 1 Depress the ON OFF switch to ON The pilot lamp will light The remote control unit has now energized the pan tilt head camera housing and motorized zoom lens WV 7160 only 2 To turn on the camera depress the Camera Control 3 To pan or tilt the head operate the joystick Pan Tilt Control for UP DOWN LEFT and RIGHT To drive in two axes at once incline the lever of this control to desired direction pA Down and left DON Down and right e The following operations are only for use with the Camera Housing WV 7160 4 If a motorized zoom lens is mounted on the camera it is possible to remote control the ZOOM FOCUS and IRIS Ron Depress the Zoom ocus or lris Control upward cr downward for obtaining the desired condition Focus t Iris Defroster 5 Turn the Defros
7. the cover TYPICAL SYSTEM CONNECTIONS Camera Housing Remote Control Unit WV 7360 WV 7150 7160 Control Cabl ii e AC 120V 60Hz 8 or 9 conductors WV 7150 14 or 15 conductors WV 7160 ooo Monitor S Coax Cable AC 120V 60Hz SPECIFICATIONS STANDARD ACCESSORIES Supplied e Pan Tilt Head WV 7260 WV 7360 WV 7460 optional Tilting speed Approx 3 6 sec Mountable housing WV 7150 WV 7160 optional f _ Up 15 Down 60 Tilting angle ower source Load weight Less than 44 Ibs 20 kg Power consumption Approx 24W Ambient AF 122 EL 20 C450 C 83 16 W x 11 13 16 H x 10 7 8 D Panning angie 10 340 adjustable 208 W x 300 H x 276 D mm Remote Control Unit WV 7360 Pan tilt head WV 7260 x 1 optional Manual UP DOWN Power Source 120V AC 60Hz M Power supply AC 24V DC 6V Max 135W including WV 7260 Ambient a o ax 135W including 26 m Mu 14 F 122 F 10 C 50 C Panasonic 24V AC camera Operating temperature Ambient operating Less than 90 8 3 8 IW x 313 16 CH x 6 11 16 D 210 W x 95 H x 170 D mm Power consumption heater blower defroster wiper and motorized zoom lens Camera power panning tilting zoom focus iris defloster and Dimensions wiper Manual RIGHT LEFT Controls e Pan Tilt Head WV 7260 Remote Control Unit WV 7360
8. to qualified service personel WV 1004 1054 1104 1154 with outdoor camera hous ing such as the Model WV 7150 7160 External sync can not be supplied with this installation Remote Control Unit WV 7360 WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE Remote contro unit TO RAIN OR MOISTURE 1 Do not attempt to disassemble this unit There are no user serviceable parts inside Refer servicing to qualified service personel 2 Use this unit within its rating Designed for outdoor use Ambient temperature must not range beyond 4 F 122 F 20 C 50 C 2 Use this unit within its rating e Designed for indoor use Ambient temperature must not range beyond 14 F 122 F 10 C 50 C Avoid using this unit when humidity is above 90 3 Do not mount this unit inverted outdoors This unit has been assembled for upright mounting When it is mounted in the inverted position it is not protected from rain 3 he input power source must be t20V 10 4 Select a flat location which can support the entire 108 132V AC 60Hz Me Daa IR Dee aCe ie yet nero erm Quse 4 The Remote Control Unit can control only one Pan Tilt Head MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS e Pan Tilt Head WV 7260 Rear c3 C gt Front Front Indication Camera Housing Mounting Holes 4 3 8 4 8 See page 4 Guide Pine Cover Camera Housing Mounting Plate
9. n t n 7 SPECIFICATIONS i e up ete Tuer eer do ees aea ig em at e CA e ae SS iue ra 8 STANDARD ACCESSORIES 43 edu sane oer Ma Ox Se Bae We A Re ae Rn 8 OPTIONAL ACCESSORIES 5s sra ex exe ours epi cad MR REESE ae eed oben RE ES 8 SCHEMATIC DIAGRAM xaxa sed Cice X ACIE pan seat wee ex OR Ben OK ads dae e Ra NR ZAR eee 8 OUTEINE DRAWING selu hee da er Oe 1e PRE TAG Nj Que S RC eR RUN eR ICE UN ee os 9 INTRODUCTION The WV 7260 heavy duty outdoor Pan Tilt Head with The WV 7360 Remote Control Unit which can be mounted Remote Control Unit allows remote control of camera in an optional 19 rackmount frame supplies low voltage panning and tilting with Outdoor Camera Housing Pan Tilt 24V AC to both one Pan Tilt Head and Camera Housing Head may be directly mounted on a flat surface The as well as a low voltage camera It also supplies low voltage camera can be panned from an angle of 10 340 ata 6V DC to a motorized zoom lens Controls ON OFF speed of 7 2 second and can be tilted from an angle of up power for low voltage camera zooming focusing and iris 15 down 60 at a speed of 3 6 second for zoom lens panning and tilting wiper and defroster for camera housing PRECAUTIONS Pan Tilt Head WV 7260 5 The input power source must be 24V ea 19 26 4V 1 Do not attempt to disassemble this unit AC 60Hz There are no user serviceable parts inside Refer servicing 6 Mount a low voltage camera 24V AC such as the Model
10. rating e Recommended wire gauge size for 24V AC lines when using a camera whose power consumption is 13 watts Table 1 720 0 52mm 18 0 83mm 16 14 2 When mounting the outdoor camera housing on the Mounting Plate Four M8x20mm 5 16 x13 16 hex head bolts plain washers and lockwashers are provided with the Pan Tilt Head Use these to mount the camera housing as shown below e Be sure to align the camera direction and front direction of pan tilt head To the guide pin hole of camera housing To the four mounting holes of camera housing Plain Washer ma Part No XWABBV Lock Washer Part No XWG8V Hex head bolt H Part No X VG8C20V 2 Direct contro with Camera Housing WV 7160 and Motorized Zoom Lens Select a multi conductor cable with 14 or 15 con ductors The wire gauge can be determined by the Table 2 The wire should meet FR 1 rating Recommended wire gauge size for 24V AC lines when using a camera whose power consumption is 13W and optional wiper Table 2 Copper 130 mo m 399 0 52mm 18 115 65 20 83mm imi 16 U im o o Omm im 9 V6 Note These values show the wire length when rat d voltage 120V AC is applied to the remote control unit WV 7360 3 Zoom Control with Camera Housing WV 7 160 Use a motorized zoom lens which can be controlled as follows TELE 6V DC WIDE 6V DC
11. ter Control on or off 6 Turn the Wiper Control on or off When the optional Wiper Unit WV Z50 is mounted to the Camera Housing WV 7160 ADJUSTMENTS After cable is assembled and unit connected plug the 5 With both limit stops in place pan to both stop Remote Control Unit into a 120V AC source and proceed Positions and recheck for exact trim of limit stops as follows Tighten both stops securely A Panning Angle Us B Tilt Limit Stop 1 Loosen the Pan Limit Stops 1 Remove the Tilt Limit Adjustment Cover Pan Limit Stop Left Pan Limit Stop Right UP 0 15 Tilt Limit Stop Tilt Limit Stop Up Down 2 Turn on the ON OFF switch to energize unit then 2 Loosen the two recessed Tilt Limit Stops and rotate rotate Pan Tilt Head using joystic Pan Tilt Control until Pan Tilt Head using joystick Pan Tilt Contro until desired right pan limit is reached desired up limit is reached 3 Locate the right pan limit stop and move until it 3 Move the up limit stop toward bottom end of slot until a contacts limit switch actuator Move stop additional clock can be heard Tigten screw slight amount to deflect actuator until a click is heard 4 Adjust the down limit stop the same way indicating opening of limit switch Lock stop in place 5 Lock limit stops securely in place after checking for 4 Rotate Pan Tilt Head to the desired left limit position trim Adjust left pan limit stop as before 6 Replace
Download Pdf Manuals
Related Search
PanasonicWV 7260 MV 7360 Manual