Home

Panasonic CY-RC50KU Manual

1. Rear view camera 4 m Ground lead Black EC To a metal part of the vehicle body Connect to an area of exposed metal not Reverse lead covered with paint etc Violet white stripe m To the wire of the reverse lamp REVERSE Fuse 1A Do not connect to a point that has a constant power supply Note e Insert connectors securely Also take care to avoid pulling on the cords e Do not extend the RCA cord or rear view camera cord as video noise and breakdowns could result e Only use clip connectors in the specified places yding to the installation instructions for the connected devices Connection to a Car Navigation System example Connect to the CD wire of the reverse lamp lamp with a transparent lens which lights for reversing which lights when the vehicle shift lever is moved to reverse R Transmission Clip connector Reverse lamp supplied with x CN NVD905U Clip connector S TIE TES A Reverse lead S Rr EESTI A 9 Violet white stripe Battery Cut off the end terminal EL m um d enifeonnect ioe dps Reverse lead Ground lead arae connector Violet white stripe Black ar enasi m N ner ear view camera SZ Car Navigation System control unit r1 MES CN NVD905U option t El Ol Yellow Rear view camera 4 m Rear view camera RCA conversion cable RCA cord t supplied
2. This warranty gives you specific legal rights and you may also have other rights which vary from state to state If a problem with this product develops during or after the warranty period you may contact your dealer or Servicenter If the problem is not handled to your satisfaction then write to warrantor s Consumer Affairs Department at the addresses of the warrantor PARTS AND SERVICE WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR RESPONSIBILITY Customer s Record exchanged at the place of purchase Contact your Dealer for details Accessories in exchange for defective items Ninety 90 Days Not Applicable During the Labor warranty period there will be no charge for labor During he Parts warranty period there will be no charge for parts You must carry in or mail in your product prepaid during the warranty period If nonrechargeable atteries are included they are not warranted This warranty only applies to products purchased and serviced in the United States or Puerto Rico This warranty is extended only to the original purchaser of a new product which was not sold as is A purchase receipt or other proof of the original purchase date is required for warranty service CARRY IN OR MAIL IN SERVICE For Carry In or Mail In Service in the United States call 1 800 211 PANA 7262 or visi Panasonic Web Site http www panasonic com For assistance in Puerto Rico call Panasonic Sales Company
3. e Do not wipe with volatile chemicals such as alcohol benzine thinners and gasoline These can cause deformation deterioration and breakage Do not wipe with cleaners that contain abrasive particles as they leave scratches e f the lens is dirty wipe it gently with a soft moist cloth Wiping strongly with a dry cloth will damage the lens Alcohol Pesticide Thinner Benzine Limited warranty PANASONIC CONSUMER ELECTRONICS COMPANY DIVISION OF PANASONIC CORPORATION OF NORTH AMERICA One Panasonic Way Secaucus New Jersey 07094 PANASONIC SALES COMPANY DIVISION OF PANASONIC PUERTO RICO INC Ave 65 de infanteria Km 9 5 San Gabriel Industrial Park Carolina Puerto Rico 00985 PANASONIC AUTO PRODUCTS LIMITED WARRANTY LIMITED WARRANTY COVERAGE if your product does not work properly because of defects in materials and workmanship Panasonic Consumer Electronics Company or Panasonic Sales Company or re install an installed unit if applicable travel to and from the sevicer and loss of media data or other memory contents The items listed are not exclusive but are for illustration only ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the exclusions may not apply to you
4. 787 750 4300 or fax 787 768 2910 LIMITED WARRANTY LIMITS AND EXCLUSIONS This warranty ONLY COVERS failures due to defects in materials and workmanship and DOES NOT COVER normal wear and tear or cosmetic damage The warranty ALSO DOES NOT COVER damages which occurred during shipment failures which are caused by products not supplied by the warrantor failures which result from accident misuse abuse neglect bug infestation mishandling misapplication alteration faulty installation set up adjustment maladjustment of consumer control improper maintenance improper antenna inadequate signal reception or pickup power line surge improper voltage supply lightning modification commercial use such as use in hotels offices restaurants or other business uses or rental use of the product or service by anyone other than the technician from Factory Servicenter or other authorized service centers or damage that is attributable to acts of God THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER LIMITED WARRANTY COVERAGE THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY As examples this excludes damages for lost time cost of having someone remove collectively referred to as the warrantor will for the length of the period M s indicated in the chart below which starts with the d
5. from other devices Fire electric shock or accident could result J After mounting and wiring the system check that all vehicle systems function normally If any vehicle equipment brakes lights horn hazard and indicator lights etc does not work normally fire electric shock or accident could result L Keep screws and other small components away from small children There is a risk that they could swallow small components Seek immediate medical attention if that happens Notes on use Carefully read the instruction manuals for the connected devices Car Monitor etc Before reversing always check behind you by eye e This product uses mirrored display which mimics the orientation of the rear view and side mirrors and is for checking the view behind the vehicle e t is intended to augment the driver s field of vision behind the vehicle It is not able to view all hazards and obstacles t uses a wide angle lens which makes close areas appear wider and further areas narrower This may cause perceived distances to differ from actual distances This product can be connected to a monitor etc with RCA type video inputs When the shift lever is in reverse R the linkage function camera interrupt display and scaled display correspond to the connected display device so we are unable to guarantee normal operation Check the mounting of the system components regularly Check that there are no loose scr
6. may cause the system to fall resulting in accident or injury Water entering inside the camera can result in a fire electric shock or breakdown Observe the following cautions when installing 1 Do not damage cords Do not damage pull bend twist or modify cords place heavy objects on them or place them near hot equipment or in contact with hot parts of the vehicle Breaking or shorting cords could cause fire electric shock or accidents Route cords so that they cannot be pinched by the body of the vehicle screws or moving parts seat rails etc Do not press cords with the point of a screwdriver or similar implement L Do not damage the rear view camera cord Water and moisture can move along the cord from the damaged area and enter the camera causing fire electric shock and breakdown J Route the rear view camera cord inside the vehicle so that water cannot penetrate them If water enters the vehicle during rain or car washing it could cause fire or electric shock J Order wiring mounting and dismounting work from a specialist engineer Wiring mounting and dismounting work requires specialist skills and experience For safety ask your dealer to perform such work In the case that this system is installed in a vehicle with a drive computer or a navigation system improper removal of the battery may result in erasure of system s memory J Only use the accessories provided and the parts specifie
7. with CN NVD905U Yellow 6m Connection to a Car Monitor example Ge to the wire of the reverse lamp lamp with a transparent lens which i lights for reversing which lights when the vehicle shift lever is moved to reverse R Transmission Clip connector y Ex OL Reverse lamp oza 9 P Clip connector oi SS SSS eee Reverse extension cord i LI Violet white stripe V Reverse lead Ground lead Car chassis Reverse lead Violet white stripe Black Violet white stripe LELEII Rear view camera control unit t In Dash Monitor CQ VD7005U option Rear view camera 4m Yellow Camera input terminal RCA cord Yellow Yellow 6m _ s CAMERA IN Connection to a Car Monitor from another company example Connect to the CD wire of the reverse lamp lamp with a transparent lens which lights for reversing which lights when the vehicle shift lever is moved to reverse R Transmission Clip connector L Reverse lamp A al ww Clip connector Ge gt scene Pes REVERSE ray GND Video input Reverse lead Ground lead Violet white stripe Black Car chassis Car Monitor NTSC Only Yellow Rear view camera control unit 1 fe T eo Bb Rear view camera 4m Yellow Reverse lead RCA cord Cut off the end term
8. P THE PRODUCT TO A SERVICENTRE Carefully pack and send prepaid adequately insured and preferably in the original carton Include details of the defect claimed and proof of date of original purchase Specifications Output image sse Wide angle mirror image for checking the rear view Vid o TOltnalz eS P dendi NTSC composite Power Supply eter tiere ds DC 12 V negative ground MM 1 6 W approx 135 mA RU ee Color CCD solid state 6 35 mm disti hte ennt tette love o E A Approx 250 000 pixels HI ME eet Se act Sa a ak of anata ae J Wide angle focal length f 1 94 mm F 1 2 8 Angular field of view esses Horizontal 134 Vertical 103 S N Tatio cts is tu ER DE on 46 dB or more at recommended light level Horizontal resolution eeeeeeeeeeennnn 330 TV lines at center BrightneSs range daB ERAS Approx 1 5 Ix 100 000 Ix Imag outplt se sete ties Eme 1 Vp p 75 Q Dimensions W x H x D Rear view camera 23 mm x 21 mm x 20 mm e x 7e x Ve cord length 4 m not including projections on the rear e Rear view camera control unit 76 mm x 27 mm x 40 mm 3 x 1 1 6 x 12e Weight Rear view camera Approx 90 g 3 2 oz including cord Rear view camera control unit sess Approx 110 g 3 9 oz Note e Specifications and the design are subject to modification without notice due to im
9. Panasonic Universal Rear View Camera Model CY RC50KU Operating Instructions CAMERA VIDEO OMEN IN OUT e Please read these instructions including Limited Warranty and Customer Services Directory carefully before using this product and keep this manual for future reference English Safety information 2 Read the operating instructions for the unit and all other components of your car navigation system carefully before using the system They contain instructions about how to use the system in a safe and effective manner Panasonic assumes no responsibility for any problems resulting from failure to observe the instructions given in this manual This pictograph alerts you to the presence of important operating instructions Failure to heed the Warning instructions may result in severe injury or death CJ This manual uses pictographs to show you how to use the product safely and to alert you to potential dangers resulting from improper connections and operations The meanings of the pictographs are explained below It is important that you fully understand the meanings of the pictographs in order to use this manual and the system properly This pictograph alerts you to the presence of important operating instructions Failure to heed the instructions may Caution result in injury or material damage A Warning Observe the following warnings when usin
10. act us via the web at http www panasonic com contactinfo You may also contact us directly at 1 800 211 PANA 7262 Monday Friday 9 am 9 pm Saturday Sunday 10 am 7 pm EST For hearing or speech impaired TTY users TTY 1 877 833 8855 Accessory Purchases Purchase Parts Accessories and Instruction Books online for all Panasonic Products by visiting our Web Site at http www pasc panasonic com or send your request by E mail to npcparts panasonic com You may also contact us directly at 1 800 332 5368 Phone 1 800 237 9080 Fax Only Monday Friday 9 am to 8 pm EST Panasonic Services Company 20421 84th Avenue South Kent WA 98032 We accept Visa MasterCard Discover Card American Express and Personal Checks For hearing or speech impaired TTY users TTY 1 866 605 1277 Service in Puerto Rico Panasonic Puerto Rico Inc Panasonic Sales Company Factory Servicenter Ave 65 de Infanteria Km 9 5 San Gabriel Industrial Park Carolina Puerto Rico 00985 Phone 787 750 4300 Fax 787 768 2910 WARRANTY SERVICE FOR PRODUCT OPERATION ASSISTANCE please contact Our Customer Care Centre Telephone 905 624 5505 1 800 1 800 561 5505 Fax 905 238 2360 Email link Contact Us on www panasonic ca FOR PRODUCT REPAIRS please locate your nearest Authorized Servicentre at www panasonic ca Link Servicentres locator under Customer support IF YOU SHI
11. ape E toes tape Note Do not mount the control unit in the following locations which could cause breakdowns Places exposed to water Places which could be stepped on e Dusty places Close to heater ducts or heat emitting objects e Places exposed to direct sunlight e Under the carpet or any other position that gets hot Wiring procedure Make connections and set and operate acct When connected to a Panasonic Car Monitor etc the image from the camera is automatically displayed in the screen when the shift lever is moved to reverse R For some combinations of vehicle type and device additional cords option may be required or connection may not be possible Consult your dealer or service center e For connection with products from other companies consult the manufacturer of each device Power connector POWER Always wear gloves for safety during wiring and mounting operations Camera input CAMERA IN iilnstallation procedure Disconnect the battery terminal O Make wiring connections e To avoid short circuit accidents do not connect the power cord connectors until all Video output VIDEO OUT Rear view camera control unit wiring is complete t Mount the components Yellow Reconnect the battery terminal Power cord 5m RCA cord 6 m Yellow Hj To camera image input terminal or video input terminal NTSC Only
12. ate of original purchase Serial warranty period at its option either a repair your product with new or No refurbished parts or b replace it with a new or refurbished product The Dealer s decision to repair or replace will be made by the warrantor No Categories Parts Labor Code Audio Components except items listed below One 1 Year One 1 Year A MXE Series Audio Components except items listed below Two 2 Years Two 2 Years Address Speakers One 1 Year Not Applicable Date of Defective Car Audio Speakers under warranty must be Purchase Panasonic Canada Inc 5770 Ambler Drive Mississauga Ontario L4W 2T3 PANASONIC PRODUCT LIMITED WARRANTY Panasonic Canada Inc warrants this product to be free from defects in materials and workmanship and agrees to remedy any such defect for a period as stated below from the date of original purchase CAR AUDIO PRODUCT ONE 1 YEAR PARTS AND LABOUR The labour to install or remove the product is not warranted ACCESSOIRES NINETY 90 DAYS IN EXCHANGE FOR DEFECTIVE ITEMS LIMITATIONS AND EXCLUSIONS This warranty does not apply to products purchased outside Canada or to any product which has been improperly installed subjected to usage for which the product was not designed misused or abused damaged during shipping or which has been altered or repaired in any way that affects the reliability or detracts from the performance nor does it cover any product which is used c
13. d Use of non specified parts can cause internal damage to the equipment and insecure mounting could allow it to fall off causing accident breakdown and fire L Mount the equipment securely so that it cannot come off and fall Wipe the mounting area clean of dirt wax etc then fasten the camera securely in place Re affixing adhesive parts or use of general purpose double sided tape could cause weak bonding that would allow the equipment to drop off while the vehicle is in motion causing accident or injury Check the state of bonding or mounting loose screws etc occasionally Troubleshooting If you suspect something wrong Check and take steps as described below If the described suggestions do not solve the problem it is recommended to take the unit to your nearest authorized Panasonic Servicenter The product should be serviced only by qualified personnel Please refer checking and repair to professionals Panasonic shall not be liable for any accidents arising out of neglect of checking the unit or your own repair after your checking Never take measures especially those other than indicated by jfalic letters in Possible solution described below because those are too dangerous for users to handle themselves A Warning e Do not use the unit in an irregular condition for example without sound or with smoke or a foul smell which can cause ignition or electric shock Immediately stop using the unit and co
14. door outside Fasten with cord clamps at key points then bring the cord in where the clearance from the edge of the door is wider Do not route the cord under the back door inside Tie band i The cord will be damaged if Tie to the harness cover AO pinched by the edge of the gt W j back door Car navigation etc 3 Rear view camera Rear view camera Gs control unit Cord rail Rubber water seal i Attached to rear peel off backing paper n camera Cut to the appropriate size Place against the rubber gasket and bring the cord into the interior io Z j Y Yeo 4 Rear view camera cord Cord clamp Sedan type Cord clamp Trunk lid Rear view camera Rubber gasket View with trunk lid closed Rubber water seal Attached to rear view camera Rubber water seal Attached to rear view camera Rubber gasket Attach the rubber water seal so that it is parallel with the rubber gasket when the trunk is closed Note e Open and close the back door or trunk lid slowly to check that the camera cord is not pinched or abraded by the door lid Moisture or water can enter through the damaged area of the cord and penetrate to the interior of the camera causing breakdowns e Route the camera cord as far as possible from the antenna cord It could cause noise in TV and radio signals e f AM radio broadcasts are affected by noise move the camera cord further from t
15. ews and that the camera bracket is not detached e Check that the rubber water seals where the cord enters the vehicle are parallel to the rubber gasket where they are in contact Do not display a direct view of the sun for long periods A burned image could remain on the screen Do not use a cellular telephone or wireless equipment close to the system Screen noise and malfunctions could result You are advised to use cellular telephone or wireless equipment away from this system Disclaimers e Any repairs to breakdowns or damage caused by fire earthquake third party action other accident actions of the user whether by accident or design incorrect operation or usage under other abnormal conditions will as a rule require payment of repair fees Not guaranteed when equipped in a commercial use vehicle buses trucks taxis goods vehicles etc Product servicing If the suggestions in the charts do not solve the problem we recommend that you take it to your nearest authorized Panasonic Servicenter The product should be serviced only by a qualified technician Replacing the Fuse Use fuses of the same specified rating 1 A Using different substitutes or fuses with higher rating or connecting the product directly without a fuse could cause fire or damage to this unit If the replacement of the fuse fails consult your nearest authorized Panasonic Servicenter for service Maintenance Caution on cleaning
16. g this unit CJ Always reverse slowly checking for safety with your own eyes The camera image is perceived differently from the actual distance The field of view which can be displayed is also limited Reverse slowly checking safety by eye rather than relying on the screen Reversing without checking safety can cause collisions with people and objects 1 Always use a fuse of the specified capacity Ask a specialist engineer to replace the fuse If the fuse used exceeds the specified capacity it can cause fire smoke ignition and other breakdowns Consult your dealer or service center to request fuse replacement or repair L Do not continue using the system when it has broken down or malfunctioned If there is a breakdown no image no sound etc or malfunctions a foreign object inside water on the components smoke comes out abnormal noise or odor etc immediately stop using it then consult your dealer or service center Continued use in that state could cause fire electric shock or accident A Caution Observe the following cautions when using this unit L Do not use this system for any purpose other than mounting on a road vehicle Non vehicular use such as use outdoors or on a pleasure boat could cause smoking generation ignition electric shock injury and breakdown 1 Do not use an automatic car washing machine to wash the vehicle Exposure to water from a high pressure hose or impact from a brush
17. he bolts then adjust the camera angle After adjusting tighten the s bolts securely Approx 103 Fender or the rear edge of the vehicle Approx 134 Memorandum
18. he vehicle wiring harness Mounting procedure Rear view camera Before mounting Wipe away all oil and dirt etc from the mounting surface Make connections and placement tentatively at first to check positions Repeated affixing weakens the adhesive e The screw holes to use and the possible angle adjustment vary according to the mounting position Adjust the angle and check that the required field of view is visible It is not possible to re affix components e Mount the camera so that it does not contact the vehicle body or rear wipers For secure mounting e Do not work outdoors in rainy weather e When the air temperature is low use the vehicle s interior heater or defogger or a dryer to warm the bonding area Use a dryer etc to thoroughly remove all moisture Dirt and moisture on the bonding surface reduce bond strength and could cause the camera to fall off e After mounting the camera do not expose it to rain or other water pull it or subject it to strong forces for 24 hours Note e The camera cannot be affixed to painted or glass surfaces which have been treated with fluoroplastics treatments which shed water droplets mud etc or to re painted surfaces Rear view camera control unit Before mounting Wipe away all oil and dirt etc from the mounting surface Mounting on carpet etc la on hard surfaces floor Rear view camera control unit Rear view camera control unit Velcro t
19. heck with the car manufacturer about operational cautions prior to attempting installation and perform the installation in a safe and proper manner Improper removal of the battery may result in a malfunction of a device or possibly death 24 Never use the security parts of the vehicle for mounting or grounding the system Use of the bolts or nuts of security parts steering brake systems fuel tank etc can cause brake failure fire or other accidents J Check positions of pipes tanks electric wirings in the vehicle when mounting Never interfere with or touch pipes tanks or electric wirings when opening holes in the vehicle body for installation Apply rust prevention and waterproofing treatments to the processed area as rust or water leakage may result in a fire an electric shock or other accident 24 Route cords so that they do not get in the way of occupants driving or getting into or out of the vehicle Route cords so that they do not tangle with the steering wheel shift lever brake pedals feet etc and bundle and fasten them appropriately Poorly arranged cords can cause accident and injury 2 Wire and mount the system as instructed Fire or accident could result if wiring and mounting do not properly follow the operating instructions _J Do not attempt to disassemble repair or modify the system Never attempt to disassemble repair or modify the system or to remove cord insulation to take power supply
20. inal and 6m connect to the clip connector How to disconnect locked cords How to attach a clip connector Insert the cord into the clip connector e Pulling strongly will break the cord e Check that the lock is released before disconnecting Vehicle side wiring cord Reverse lead of this unit r Power cord Rear view camera cord dh A Press the element into place Close the cover Attach the camera bracket to a glass or painted surface on the vehicle body Form the camera bracket to Peel the backing paper and press the camera fit the form of the mounting bracket firmly onto the surface surface Do not remove the backing paper e Do not touch the bonding ET surface with your hands Camera bracket ciii Donotre attach the adhesive Mount the camera body onto the camera bracket Bolt with washer E C Side view a The screw holes to use and the possible angle adjustment vary according to the mounting position Logo Logo Direction of forward motion Rear view camera Mount on the screw holes Side with logo on the side opposite uppermost the direction of forward motion X 45 Direction of forward motion Hexagon wrench Adjust the camera angle so that the fender or the rear edge of the vehicle appears at the bottom of the monitor Use the Hexagon wrench Camera field of view to loosen t
21. nsult your dealer e Never try to repair the unit by yourself because it is dangerous to do so Problem Possible cause Possible solution No image from the camera Incorrect settings or connection Check settings and cord connections e The fuse for the system or for equipment connected to it has blown Consult a Panasonic Servicenter Image is unclear s there dust or dirt on the camera Wipe the lens clean White lines vertical lines of light on the screen e f the camera is viewing the sun directly or a strong light reflection from a fender a headlight beam etc shines into it bright vertical lines can appear above and below the light source Smearing This is not a breakdown Noise on the screen When the area viewed by the camera is lit by fluorescent light or a similar light source noise can appear on the screen Flickering This is not a breakdown Screen display is hard to see e The screen display may become hard to see when it shows a dark area or an image that is bright in a small area or when the camera is hot This is not a breakdown Customer services directory USA CANADA Obtain Product Information and Operating Assistance locate your nearest Dealer or Servicenter purchase Parts and Accessories or make Customer Service and Literature requests by visiting our Web Site at http www panasonic com support or cont
22. ommercially Dry cell batteries are also excluded from coverage under this warranty This warranty is extended to the original end user purchaser only A purchase receipt or other proof of the original purchase date is required before warranty service is performed THIS EXPRESS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN NO EVENT WILL PANASONIC CANADA INC BE LIABLE FOR ANY SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES In certain instances some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or the exclusion of implied warranties so the above limitations and exclusions may not be applicable Check the contents Consult your dealer if any item is missing e Figures in are quantities Rear view camera Rear view camera Camera bracket Bolts with washer with Rubber water seal control unit Hexagon wrench Power cord RCA cord Clip connector Cord clamp Cord rail Tie band Velcro tape Double sided tape S gt 30 x 70 mm 1 E Accessories Operating instructions Owners information this manual card Cord routing example Route the camera cord so that it does not allow rainwater etc to penetrate Allow enough slack in the cord so that it is not pulled when the door is opened and closed Hatchback or Van type Route the cord above the back
23. provements in technology e Some figures and illustrations on this manual may be different from your product Panasonic Consumer Panasonic Sales Company Panasonic Canada Inc Electronics Company Division of Panasonic Puerto 5770 Ambler Drive Division of Panasonic Rico Inc PSC Mississauga Ontario Corporation of North America Ave 65 de Infanteria Km 9 5 LAW 2T3 One Panasonic Way Secaucus San Gabriel Industrial Park http www panasonic ca New Jersey 07094 Carolina Puerto Rico 00985 http www panasonic com http www panasonic com 2007 Matsushita Electric Industrial Co Ltd All Rights Reserved YEFM285995 F0207 0 Printed in Japan A Warning Observe the following warnings when installing T Use on a DC 12 V grounded vehicle This system can only be used on a DC 12 V O grounded vehicle It cannot be used in DC 24 V and other battery system large trucks diesel vehicles for use in cold regions etc Use on such vehicles would cause fire and breakdown A Disconnect the battery terminal during performing any wiring or installation work Wiring or installation work with the battery terminal connected could cause electric shock and injury from shorting 2 This system should be installed in a way so that operation of vehicle protective devices such as an air bag is not hindered Should this system be installed in a vehicle with a protective device such as an air bag or an anti theft system c

Panasonic CY-RC50KU Manual

Contents

Download Pdf Manuals

Related Search

Related Contents