Panasonic AKHRP900P Manual
Contents
1. Tally LED TALL Y It is lighted red when tally signal is input to the tally signal input terminal Controls and their Functions Q Menu operation switch MENU Operation switch for camera menu Item selection or data change can be done by turning this switch When this switch pushed the item and data are settled Q Menu ON switch MENU ON Used to turn the camera menu ON OFF Preset memory switch MEMO Preset memory can be done up to 5 points with respect to lens zoom focus and iris position when iris select switch is at MANU When using the preset memory first set the lens focus zoom and iris Next push this switch then the switch is lighted Subsequently push the desired preset position select switch With the data stored in the memory the switch is lighted Preset position select switch PRESET It calls the lens zoom focus and iris settings previously stored in the memory and brings the lens into preset operation Speed change switch SPEED High speed operation is obtained when the zoom operation lever and the focus adjust lever are operated while pressing this switch The switch is lighted while being pressed D Zoom operation lever ZOOM TELE WIDE Used for zoom operation of the lens The zoom speed changes with the shifting angles of the lever With the zoom operation lever direction change switch set at NOR when the lever is shifted to TELE the zoom operates in a telescopic mode a2. erating nstructions Camera Controller Model AK H HP900P Panasonic Before attempting to connect operate or adjust this product please read these instructions completely and save this manual for future use For Your Safety CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and main tenance servicing instructions in the literature accompanying the appliance For CANADA This class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada l 12 Volt Class II Power Supply Only For Example AW PS505P L 1 is the safety information FCC Note This device complies with Part 15 of the FCC Rules To assure continued compliance follow the attached instal lation instructions and do not make any unauthorized modifications This equipment has been tested
3. their Functions MRear panel CAMERA 1 F eo OO Id ank 206 DC 12V IN i O oec eO O Camera connector CAMERA I F Connected to the camera AK HC900P with the attached cable Sean Pin No Signal Pin No Signal 94594491391211 O10 O40 040 0 9 0 1 Y signal output 8 Y signal GND a Pb signal output 9 Pb signal GND 8 Pr signal output 10 Pr signal output 4 Syncsignalinput 11 SyncsignalGND 58 pew 12 DCGND 6 FrameGnD 13 TXD 7 Tom 14 Rx 5 XD TXD Data from camera to remote controller RXD Data from remote controller to camera Swivel stand control signal input connector P T CONT RJ 45 Connects the swivel stand control signal output of the pan tilt control panel AW RP301 Monitor signal output connector Y G Pb B Pr R BNCx3 Outputs the analog signal from the camera The output can be changed to R G B Y Pb Pr by the camera menu setting Synch signal input connector G L IN BNC x 1 Inputs the sync signal to the camera Input 3 value SYNC as the synch signal Tally signal input connector TALLY IN 2 pin connector block Connected to the tally connector from the system When the HOT connector is at GND level the tally LED is lighted Controls and their Functions Breaker BREAKER DC power breaker The breaker operates to cut off the power in case of
4. 5 spec lens E HD SDI Coaxial cable 5C FB Multi purpose digital camera AK HC900P eeu DOETE bbe CRIARI LI t zoom focus control cable AC adapter AW PS505P Multi cable 17ft AK HDMLTCAO05 HD monitor E AW PH300A z AC adapter AC adapter AW PS505P AW PS300 Swivel stand control is possible for AW 00000 ooooo000001 O 90000085 Bi B O Swivel stand controller AW RP301 PH500 PH600 as well Camera controller AK HRP900P AC adapter AW PS301 16 Communication Speed Setting The communication speed is factory adjusted to 38 4Kpbs In case it does not match the communication speed of multi purpose camera AK HC900P the alarm LED is lighted Remove the rear panel and change the DIP SW on the board and adjust it to the communication speed of the camera amp Yd O E nai eL n PT Remove the t screw and open the bottom enon iga ii plate then DIP CC ILI SW can be seen i 3 E A MS 7 in there 5 8 2341 3 ik 2 3 125Kbit Sec it E O 12345678 SW3 Change the communication report by the combination of SW3 No 1 and No 2 on ROP CPU board 38 4Kbit Sec O 9600Kbit Sec 10 17 Example of Rack Mount How to rack mount Install the main body on the rack as shown below Remove the rack mount bracket screw when
5. CHNICAL SUPPORT Emergency 24 Hour Service 800 222 0741 Panasonic Canada Inc 5770 Ambler Drive Mississauga Ontario LAW 2T3 905 624 5010 Panasonic de Mexico S A de C V Av angel Urraza Num 1209 Col de Valle 03100 Mexico D F 52 1 951 2127 Panasonic Sales Company Division of Matsushita Electric of Puerto Rico Inc San Gabriel Industrial Park 65th Infantry Ave Km 9 5 Carolina Puerto Rico 00630 787 750 4300 Printed in Japan P VQTOA79 F0902H D
6. PH300A AW PH500 AW PH600 and an adapter suited for the swivel stand When no swivel stand is used connect both of the motor driven zoom lens iris control cable and remote zoom focus cable to the camera see page 13 When a swivel stand is used connect the iris control cable to the camera and the remote zoom focus cable to the swivel stand see the illustration below For the connection system of each unit refer to pages 14 to 16 Connect the motor driven zoom lens iris control cable to the camera and the remote zoom focus control cable to the swivel stand If the motor driven zoom lens remote zoom focus control cable is connected to the camera the lens cannot be controlled 12 Remote zoom focus control cable Iris control CONTROL IN 1394 _IPIRP DU iN To iris connector To lens interface connector How to Connect llLens connection in the case of no swivel stand lHow to mount the lens e A lens of any makers can be used provided that it is a bayonet type B4 mount lens of 2 3 inch standard Turn the lens fixing ring knob counterclockwise and remove the lens mount cap 2 Mount the lens and completely secure it by turning the lens fixing ring knob clockwise Connect the iris control cable to the lens connector Connect the remote zoom focus control cable to the zoom focus connector on the rear panel Note that some lenses are uncontrollable wit
7. and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are de signed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equip ment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARNING TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE CAUTION TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE USE THE RECOM MENDED ACCESSORIES ONLY The serial number of this product may be found on the bottom of the unit Contents FOL Y OUb45 diei seattle PES qut phis Qoae ee MI aiuta 2 OUE se inea E e nia on dco a tea aida 4 Check the Accessories iaia 4 PC CAUMOMNS TOUSE CR NETTEN TIE TORT DIU a a 4 Controls and their Functions a 5 3 4a m dcs Ee ee dca sc dp ee rae SR oa 5 I Op ration pariel siccit 5 EGG Re TRARNE 9 BE Front panel csc suo RIdRTdAIBRI NE NDA gePGheu aan ai 11 FIOW LO COMMCCE c ua ua venite oes era iva 12 B Lens connection in the case of no swivel stand ee 13 Multi purpo
8. ect lens iris auto manual select indication change zoom operation lever direction change focus adjust direction change Adjusting function Iris lens iris zoom focus R B gain master pedestal H B pedestal Connection cable Multi cable 1 pc Cable max extension distance 33 ft 10m Operating temperature range 32 F to 104 F 0 C to 40 C Dimensions 8 5 16 W x3 1 2 H x6 15 16 D inch 210x88x176 mm Weight Approx 3 3 Ibs 1 5kg Finish AV ivory coating Munsell 7 9Y 6 8 0 8 approx color Weight and dimensions shown are approximate Specifications are subject to change without notice 21 Memo 22 Memo 23 Panasonic PANASONIC BROADCAST amp TELEVISION SYSTEMS COMPANY UNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office One Panasonic Way 4E 7 Secaucus NJ 07094 201 348 7000 EASTERN ZONE One Panasonic Way 4E 7 Secaucus NJ 07094 201 348 7621 Southeast Region 1225 Northbrook Parkway Ste 1 160 Suwanee GA 30024 770 338 6835 Central Region 1707 N Randall Road E1 C 1 Elgin IL 60123 847 468 5200 WESTERN ZONE 3330 Cahuenga Blvd W Los Angeles CA 90068 323 436 3500 Government Marketing Department 52 West Gude Drive Rockville MD 20850 301 738 3840 Broadcast PARTS INFORMATION amp ORDERING 9 00 a m 5 00 p m EST 800 334 4881 24 Hr Fax 800 334 4880 Emergency after hour parts orders 800 334 4881 TE
9. erature range of 32 F to 104 F 0 C to 40 C If used at a temperature below 32 F or higher than 104 F it may cause bad influences to the component parts e Turn off the power before connecting or disconnecting the cable When connecting or disconnecting the cable be sure to turn off the power switch of the unit beforehand e Avoid using the unit outdoors e Install the unit 3 3 ft 1 m away from the monitor e Maintenance Pull out the power cord plug and clean the unit with dry cloth If it is hard to clean moisten the cloth with a diluted neutral detergent solution and squeeze it well and lightly wipe the unit Precautions e Do not use volatile solvents such as benzene or thinner e When using a chemical mop carefully read the instructions Controls and their Functions llOperation panel I Canf ra Controller Sc NE OPERAT AL nM P B PRE m B B qu ii lp CLEAR a Wm oO i i sw L 00 0 co o 0 ESS 7 11 6 op OFF me se O oo Q s Q 3 a9 Q Power indication LED POWER It is lighted green when the power control switch is ON It goes out when the power control switch is OFF Power control switch POWER ON OFF With this switch turned ON the unit and the camera connected are simultaneously turned on With it turned OFF both of the unit and the camera are turned off SD card slot SD CARD With an SD card inserted the camera setting data can be recorded on the SD card
10. h respect to zoom and focus function Remote zoom focus control E C ab l e Panasonic 200M Connect the cable to the swivel stand when used 5d Iris control cable to lens connector Lens fixing ring knob 13 Multi purpose digital camera control system configuration 1 Remote zoom focus control cable HD SDI Coaxial cable 5C FB D SUB 15 pin Remote Multi purpose digital control ae AK HC900P spec lens Multi cable 17ft AK HDMLTCA05 HD monitor EJ AC adapter B AW PS505P Ext sync signal 3 value SYNC 7 vorri i i di DC power cable D SUB 15 pin Camera controller AK HRP900P 14 Multi purpose digital camera control system configuration 2 Remote control spec lens HD SDI Coaxial cable 5C FB Remote zoom focus control cable Multi cable 17ft Multi purpose digital camera AK HDMLTCA05 AK HC900P AC adapter AW PS505P HD monitor Swivel stand Dl AW PH300A AC adapter AW PS505P Ext sync signal 3 value SYNC J Swivel stand control is possible for AW 00000 ooooo00000 O 900000085 Bi B O Swivel stand controller AW RP301 PH500 PH600 as well Camera controller AK HRP900P AC adapter AW PS301 15 Multi purpose digital camera control system configuration 3 Remote Multi cable 1 7ft control AK HDMLTCA0
11. installing Rack mount bracket Coupler N Attached screw Coupler fitting holes 18 Example of Rack Mount lHow to change the rear panel position a Remove the three screws on the Install the rear panel on the bottom with bottom to remove the blank panel the three screws 2 Remove the three screws on the rear Install the blank panel on the rear side panel to remove the rear panel with the three screws When installing take care so that the internal wires are not caught by the panel 19 Appearance and Dimensions 20 Panasonic ON OFF POWER o TALLY on MENU ZOOM NOR zer nev ILL SD CARD 8 G L IN TALLY IN OPERATE ILI 5 16 ALARI o 210 MODE CAM BAR TEST ELE amera Controller SCENE PRE USERI USER2 rc ATO WHITE BLACK mm 5 8 14 5 6 15 16 176 Specifications Power supply DC 12V XLR 4 pin connector Power consumption 5 W camera controller only lis the safety information Swivel stand control input Control signal RJ 45 8P modular jack System tally input Tally signal 2P connector block Switch function Power control preset memory preset position select speed polarity change menu ON OFF menu operation operation panel active scene file select mode select auto white start auto black start ND filter select CC filter select gain select shutter sel
12. nal With the switch set to BAR TEST the color bar signal and the test signal are output from the monitor signal output terminal of this unit With it set to CAM the picture taken by the camera is output D Auto white start switch AUTO WHITE With this switch pressed the white balance is automatically adjusted During the operation WHTE LED blinks and it goes out when the adjustment is normally finished In case of NG it lights up for a while and then goes out Note It does not operate when the mode is BAR Auto black start switch AUTO BLACK With this switch pressed the lens is automatically closed and the black balance is adjusted During the operation BLACK LED blinks and it goes out when the adjustment is normally finished In case of NG it lights up for a while and then goes Out D R B gain adjust volume GAIN Used to adjust the R B signal gain of the camera D R B pedestal adjust volume BLACK Used to adjust the R B signal pedestal level of the camera ND filter select switch ND FILTER Used to select the optical filter ND of the camera CC filter select switch CC FILTER Used to select the optical filter CC of the camera Controls and their Functions Gain select switch GAIN Used to select the master gain of the camera It changes in the order of OdB 9dB 18dB S1 Super gain 1 S2 3dB 0dB Note For super gain setting check with the camera menu Shu
13. nd when shifted to WIDE it operates in a wide angle mode With the zoom operation lever direction change switch D set to REV the zoom can be operated in the opposite direction Focus adjust lever FOCUS FAR NEAR Used to adjust the lens focus The focus can be controlled in speed variable fashion by regulating the shifting angle of this lever With the focus adjust direction change switch amp set at NOR when this lever is shifted to FAR the focus is adjusted to a far distance and when shifted to NEAR the focus is adjusted to a near distance With the focus adjust direction change switch amp set to REV the focus can be adjusted in the opposite direction D Operation panel active switch OPERATE This is an active switch for panel function It can be operated when the switch is lighted It does not work when the switch is not lighted Controls and their Functions Alarm indication LED ALARM It lights up when an alarm is generated in case of fan stop wrong communication speed etc Note In case of wrong communication speed change the DIP SW position in the unit to match the camera and communication speed so that the alarm goes out D Scene file select switch SCENE Used to select the scene file previously set on the camera Note With PRESET selected it results in the factory adjusted setting D Mode select switch MODE Used to select the camera color bar signal test signal and camera picture sig
14. over current DC12V input connector DC12V IN XLR4 pin Connects the AC adapter We recommend that the AW PS505P option is used 10 Controls and their Functions WFront panel Zoom operation lever direction change switch ZOOM REVERSE Used to change the direction of the zoom operation lever With this switch set at NOR when the zoom operation lever is shifted to TELE the zoom operates in a telescopic mode and when shifted to WIDE zooming is made in a wide angle mode With this switch set to REV it can be operated in the opposite direction Also with this switch set to REV the operating direction does not match the indication on the panel In that case use the attached seal for proper indication Focus adjust direction change switch FOCUS REVERSE Used to change the direction of the focus adjust lever With this switch at NOR when the focus adjust lever is shifted to FAR the focus is adjusted to a far distance and when shifted to NEAR the focus is adjusted to a near distance With this switch set to REV focusing can be made in the opposite direction Also with this switch set to REV the operating direction does not match the indication on the panel In that case use the attached seal for proper indication 11 How to Connect Make the connection with power supply to the unit turned off Use AW PS505P option as the AC adapter for control panel Use a swivel stand AW
15. se digital camera control system configuration 1 14 Multi purpose digital camera control system configuration 2 15 Multi purpose digital camera control system configuration 3 16 Communication speed setting llli 17 Example Gr Rack MODI s use Y awe poked eri nu 18 BN How TO ACK MOURNE icona B ates n eoo carded 18 l8 How to change the rear panel position 19 Appearance and DIMENSIONS 20 SPEGHICA MAS uasa ucc sn avs Dudas qn quce xi dient aud lieti 21 Outline e his unit is a camera controller for multi purpose camera AK HC900P This unit is connected to a multi purpose camera with one multi cable and capable of transmitting and receiving various camera and lens control signals analog picture signals of cameras and generator lock signals 3 value SYNC e he extension distance between this unit and the camera is 33 ft 10m max e t is possible to control the swivel stand from the pan tilt control panel AW RP301 by using the swivel stand control input connector Check the Accessories COUDIIFIC inps 1 pc OCISCIOWS oix ence abo ics utis tio 8 pcs Multi cable 1 pc M4x8mm 4 pcs Seal 42x2 freie La eats Rd 1 pc M5x8mm 4 pcs Precautions for Use e We recommend that the AC adapter AW PS505P is used for power supply e Handle the unit with care If dropped or given a strong shock it may cause a trouble or accident e Use the unit in a temp
16. tter select switch SHUTTER OFF STEP SYNCHRO Used to select the electronic shutter of STEP and SYNCHRO set on the camera Note For electronic shutter setting check with the camera menu Indication change switch CHECK Used to change the indication item Indicator It indicates the F value of iris Master pedestal adjust volume M PED Used to adjust the pedestal setting of Y luminance signal of the camera Lens iris auto manual select switch IRIS AUTO Used to select the lens iris adjusting method With the switch set to AUTO the lens is shifted to auto iris mode and the iris is automatically adjusted according to the amount of light coming into the lens With the switch set to MANU the lens iris can be moved in the range from close to open by turning the lens iris adjust VR volume When storing the lens iris in the preset position select switch by using the preset memory switch set to MANU mode It does not work in AUTO mode Iris adjust volume IRIS When the lens iris auto manual select switch is set at MANU the lens iris can be moved in the range from close to open When the lens iris auto manual select switch is set at MANU press the preset position select switch to call the preset memory then the lens iris position is set to the preset memory position irrespective of the VR volume position After that when the VR is turned the lens iris returns to the value of VR Controls and
Download Pdf Manuals
Related Search
Panasonic AKHRP900P Manual