Panasonic NI-350S electric iron Manual
Contents
1. steaming action will stop NOTE Do not use the steam buiton unless the iron is sufficiently hot enough to produce steam otherwise water will leak out through the vents instead HOW TO USE AS A DRY IRON 1 Press the steam button down to the dry position 2 Place the iron vertically set the selector dial to OFF 3 Plug in the iron 4 Set the temperature selector dial to the desired position Refer to the Fabric Ironing Chart in this manual on page 10 5 Preheat the iron until the indicator light goes out usually about 1 2 minutes HOW TO USE THE SPRAY FEATURE Before using the spray feature check the garment label for ironing instructions because some fabrics may spot or stain with moisture The spray feature is particularly helpful for removing stubborn wrinkles and where extra dampening is needed The spray may be used with steam or dry ironing 1 Simply pump the spray button when spray Lb pT PAA is desired If the spray doesn t work DALA immediately just keep pumping till it does E This picture is m 2 To get a finer spray pump the button vigorously To get coarser spray pump the button more slowly For best results use a quick full stroke 6 Electronic 3 Way AUTO SHUT OFF FUNCTION NI 552R 553R 560R R20NR R15NR R16NR Only 1 When the iron is left unmoved with its soleplate facing down or on its side for approx 1 minute the iron will automatically shut off power to the heater by itself 2 When2. the iron is left unmoved on its heel rest for approx 10 minutes the iron will automatically shut off power to the heater by itself 3 To turn the iron back on to resume ironing simply move the iron in any way Reheat the iron until the indicator light goes out if you have left the iron in its auto shut off mode for 10 minutes or more 1 O minutes to OFF NOTE 1 The Auto shut off system works regardless of position of the temperature selector dial even at OFF position 2 When you finish ironing always unplug the iron X Licensed under U S patent No 4 686 352 and foreign counterparts HOW TO USE THE JET OF STEAM FEATURE The jet of steam feature gives extra steam which goes deep into the garment and is helpful for removing stubborn wrinkles The jet of steam feature can be used only in the amp indication area of the temperature selector dial when steam or dry ironing if used at lower setting water spotting will occur because the iron is not hot enough to change water to steam If you have not used the Jet of Steam feature for a long time it is necessary to clean the inside of the iron before using this feature on any clothes to be ironed Simply test the Jet of Steam feature several times away from the ironing board and clothes to be ironed This will prevent brown spotting or water spotting on the clothes A _ Fill the iron as described in HOW TO FILL 2 Set the iron vertically and make sure
3. the temperature selector dial is set to OFF Plug the AC cord into the electrical outlet 3 Set the temperature selector dial to the lt gt indication area 4 Preheat the iron until the indicator light goes out usually about 1 2 minutes 5 Simply pump the jet of steam button when it is desired But pump the jet of steam button several times before using for the first time at each ironing session 6 Allow at least 5 seconds between uses of jet of steam to G g picture prevent water spotting Use a press cloth if necessary ey is NI S60R VERTICAL STEAM NI 560R Only To get better results when using vertical Jet of steam hang the garment on a clothes hanger Curtain and drapes may also be steamed once they re hung Hold the iron away from your body close to but not touching the fabric Pull the fabric tight with your free hand and pump the Vertical steam button Jet of Steam Button at 5 second intervals as you pass the iron over the wrinkled fablic WARNING Never iron clothes on the body or point your iron at anyone when steaming Keep hands and body away from steam areas while using vertical steam feature With the self cleaning feature you can flush out mineral residues from the steam generating chamber and the steam vents refreshing your iron each time for a longer steaming life It is very important to operate the self cleaning feature after each steam ironing to prevent mineral accumulations from h
4. Electric Steam Iron Operating Instructions Model No NI 350S N 350R NI 552R NI 553R NI 560R NI A20NAR NI R1SNA NI RIGNR pEr pomik Please read these instructions carefully before using this product and save this manual for future use For assistance please call 1 800 214 PANA 7262 or send e mail to cosumerproducts panagonic cam or visit Us at Www panasonic com U S A For assistance please call 787 757 4300 i or visit us at www panasonicpr com Puerto Rico IMPORTANT SAFEGUARDS When using your flatiron basic safety precautions should always be followed including the following 1 Read all instructions 2 Use iron only for its intended use 3 To protect against a risk of electric shock do not immerse the iron in water or other liquids 4 The iron should always be turned to OFF before plugging or unplugging from outlet Never yank cord to disconnect from outlet instead grasp plug and pull to disconnect 5 Do not allow cord to touch hot surfaces Let iron coo completely before putting away Loop cord loosely around iron when storing NI 350S Only Wind cord into cord reel unit when storing NI 350R 552R 553R 560R R20NR R15NR R16NR Only 6 Always disconnect iron from electrical outlet when filling with water or emptying and when not in use 7 Do not operate iron with a damaged cord or if the iron has been dropped or damaged To avoid a risk of electric shock do not disassemble the iron tak
5. R CORD NI 350R 552R 553R 560R R20NRA R15NR R16NR Only 1 When retracting power cord always grasp the plug with one hand while pressing the cord wind button with the other hand 2 If cord does not retract completely pull it out slightly and wind it again while guiding it into the ree 3 Unwind the power cord in the amount of length you need before plugging it to the wall outlet 4 If the power cord seems hard to unwind due to an improper winding pull firmly until it is released 5 Do not allow small children to handle the retractive power cord as this may cause the cord to whip and cause injury GENERAL HINTS BEFORE USING YOUR Panasonic IRON Read this instruction book to become familiar with the iron and its features Most ordinary tap water can be used in this iron In extremely hard water areas distiled or demineralized water should be used Do not use water processed through home water softening systems because this water contains minerals that may be harmful to the iron itis best to start ironing garments requiring lower temperature settings first This will help to avoid damaging garments If you are not sure of the fabric content first test the temperature of the iron on an area of a garment where it will not show HELPFUL IRONING TIPS The Temperature Selector Dial of the Panasonic iron has dots on it in addition to numbers and color indications This makes it easy to adjust the iron for steam more or les
6. TALLICS SUEDE NYLON ANTORON CAPROLAN SILK PERM PRESS RAYONS POLYESTER DACRON FORTREL KODEL TRIACETATE ARNEL W n W COTTON Trademarks of Fiber Manufacturers WOOL VELVET Dry iron on wrong side or use a press cloth on top of fabric Don t sprinkle water directly on fabric to avoid spots To iron suede cover ironing board with brown paper and use it as a press cloth Dry iron on wrong side Dry iron on wrong side To touch up collars cuffs pockets etc iron lightly on right side Steam ironing is suggested Never iron completely dry To iron velvet steam iron holding the slightly above the fabric Steam ironing is suggested Sprinkle water on the fabric depending on its thickness Iron dark fabrics on wrong side to avoid unwanted sheen Steam ironing is suggested Iron dark fabrics on wrong side to avoid unwanted sheen Panasonic Consumer Electronics Company Division of Matsushita Electric Corporation of America One Panasonic Way Secaucus New Jersey 07094 Panasonic Sales Company Division of Matsushita Electric of Puerto Rico Inc PSC Ave 65 de Infanteria Km 9 5 San Gabriel Industrial Pack Carolina Puerto Rico 00985 consumerproducts panasonic com i82006 6K36A 10
7. ardening 1 Check water level Water level should be at the 1 2 full When water level is below 1 2 full fill with water according to the instructions in How to Fill 2 Preheat at 6 setting in about 1 2 minutes Make sure that the steam button is in the Dry position 3 Set the dial to off and remove the AC plug 4 Hold the iron horizontally over the sink 5 Pump the Jet of Steam button quickly at least 3 times per second about 20 30 times While self cleaning pitch the iron up and down slowly to help clean the entire inside and let the water drip out of the sole plate vents D This picture is NI 560R 8 7 Check that all water and steam thoroughly stop coming out of the sole plate vents After self cleaning is finished dump any remaining water out of the iron 8 Iron on a towel to remove any drops of water remaining on the bottom of iron 9 Cool as usual and store the iron on its heel rest Never store an iron on its soleplate or with water in it NOTE If water still remains inside the sole plate after self cleaning operation then dry out the iron by vaporizing the remaining water setting the iron on the 6 setting And follow the instructions under AFTER EACH USE HOW TO CARE FOR YOUR IRON AFTER EACH USE 1 Turn iron off and unplug 2 Empty iron immediately after using Don t store the iron with water in it 3 Depress the steam button down into the dry position 4 Wait until the iron
8. e it to a qualified serviceman for examination and repair Incorrect reassembly can cause a risk of electric shock when the iron is used 8 Close supervision is necessary for any appliance being used by or near children Do not leave iron unattended while connected or on an ironing board 9 Burns can occur from touching hot metal parts hot water or steam Use caution when you turn a steam iron upside down there may be hot water in the reservoir SPECIAL INSTRUCTIONS 1 To avoid a circuit overload do not operate another high wattage appliance on the same circuit 2 If an extension cord is absolutely necessary a 10 ampere cord should be used Cords rated for less amperage may overheat Care should be taken to arrange the cord so that it cannot be pulled or tripped over SAVE THESE INSTRUCTIONS 1995 Matsushita Electric industrial Co LTD All rights reserved 2 COMPONENTS IDENTIFICATION NI 350R 552R 553R R20NR This picture is NI 350R Spray Button Handle Jet of Steam Button Cord Wind Button Steam Button CL Sui Cord Reel Unit AC Power Cord Water Fill Cover Spray Nozzle Thermostat Operating Indicator Light Temperature Select Indicator Soleplate Plug Water Level Indication Water Reservoir Temperature Selector Dial Water window NI 560R NI R15NR R16NR NI 350S rm Jet of Steam Butto Heel Rest Vertical Steam Button CAUTION DURING USE OF RETRACTIVE POWE
9. has cooled before storing it and always set it on the heel rest to protect the soleplate from scratching corroding or staining 5 After letting iron cool completely push the cord wind button to wind the cord Store iron vertically in a safe place after winding cord completely NI 350R 530R 552R 553R 560R R20NR R15NR RI6NR Only MAIN BODY After unplugging and cooling the iron simply wipe off with a damp cloth and if necessary use a mild detergent NEVER USE ANY HARSH CLEANERS SOLEPLATE Starch and other residue may be easily removed from the soleplate with a damp cloth To avoid scratching the finish never use a metallic pad to clean the soleplate and never place the iron on a rough surface If synthetics are ironed at too high a temperature not only is the fabric usually ruined but the iron soleplate is often covered with the melted remains of the synthetic fabric The best way to remove synthetic residue from the soleplate is to heat the iron and to iron over an old cotton rag CAUTION Never use steam iron cleaners in the iron since they may damage the inside of the iron 9 FABRIC IRONING CHART NOTES 1 Check garment for specific ironing instructions Always follow manufacturer s instructions 2 Iron blended fabrics at setting for lower temperature fiber or for the highest percentage fiber 3 Use caution some synthetics may melt at high temperature ACRYLIC ACRILAN CRESLAN ORLON ACETATE ME
10. s steam and any other temperature setting desired The dots are international fabric protection symbols for various temperature ranges N a Q3 Low Temperature Medium Temperature High Temperature Many garments are labeled with these dots as a guide for selecting the proper ironing temperature For general information about ironing temperatures refer to the handy fabric guide on the iron For more specific information use the Fabric Ironing Chart found on page 10 As a guide to the international Textile Care Labeling code the following symbols are noted for your information INTERNATIONAL TEXTILE CARE amp LABELING CODES mnu ao O Washing Bleaching Ironing Ory Cleaning A symbol crossed out indicates that the article of clothing must not be subjected to the particular treatment EXAMPLE DO NOT BLEACH X 4 Before ironing sort the garments according to the different heat settings required Iron fabrics that need a lower temperature first Do not touch plastic buttons with a hot iron because they may melt Be careful around zippers and similar items to prevent the soleplate from scratching HOW TO FILL 1 Be sure the iron is unplugged from the electrical outlet before filling gt with water Push the steam button down hold the iron open ai Water Fill Cover and slowly fill the iron with water see NOTE up to MAX indication about 5 6 ounces 160ml 2 Do not overfill Check the correct water le
11. vel with the iron in the vertical position 3 Close the Water Fill Cover NOTE Most ordinary tap water can be used in this iron In extremely hard water areas distilled or demineralized water should be used If distilled water is used the iron must be seasoned by using tap water for the first four times After that tap water should be used once a month This is necessary to coat the steam chamber for proper performance HOW TO USE AS A STEAM IRON Fill the iron as described in HOW TO FILL 2 Set the iron vertically and make sure the Temperature Selector Dial is set to OFF Plug the AC cord into the electrical outlet 3 Set the temperature selector dial to the lt gt or g3 steam zone lt zone Low steam for thin or delicate fabrics requiring a small amount of steam e9 Zone High steam for fabrics requiring a lot of steam i e thick materials items with stubborn wrinkles Preheat the iron until the indicator light goes out usually about 1 2 minutes This light will go on and off during ironing to indicate the temperature chosen by the selector dial is being maintained 5 Hold the iron horizontally and press the steam button into the steam position Steam button is regulated as follows _ D 5 NOTE 3 position steam button fan fi fh Dry Low steam High steam Button UP for High steam MED for Low steam Now steam ironing can begin 6 Anytime the iron is set vertically the
Download Pdf Manuals
Related Search
Panasonic NI 350S electric iron Manual