Home

Honeywell Dolphin 9700 Quick Start Guide

1. Replace the protective cover over the SIM socket 10 Install the battery and the battery door 11 Using the Scan Image Engine 12 Tap Start Demos Scan Demo Point the Dolphin s terminal at the bar code Project the aiming beam or pattern by pressing and holding the SCAN key one of the terminal s side buttons The red LED lights Center the aiming beam over the bar code see Aiming Options on page 13 When the bar code is successfully decoded the LED changes to green and the terminal beeps The bar code information is entered into the application in use Aiming Options 5300 Red High Vis Aiming Pattern T RS 5100 Green Aiming Beam Linear Bar Code S 2D Matrix Symbol Using the Color Camera Tap Start Demos prz Camera Demo 2 Adjust the camera settings using the menu at the top of the display screen fy Camera Demo Color 3 Pixels Brightness Flash Zoom 3 Point the terminal s camera Camera lens at the object you want Lens to capture The camera lens is located on the back panel of the terminal 4 Center the object in the Flash touch screen display 5 Press the ENT key 8 The terminal s red LED illuminates during picture capture Note Tap the green arrow a to review or edit your pictures Tap the green box o to exit the picture review edit screen 14 Soft Reset Warm Boot A soft reset re boots
2. contains the following items e Dolphin 9700 mobile computer the terminal Main battery pack 7 4V Li ion Quick Start Guide Note If you ordered accessories for your terminals verify that they are also included with the order Be sure to keep the original packaging in the event that the Dolphin terminal should need to be returned for service Front Panel Power Key Front Speaker Touch Panel Display Scan Key Indicator LED Microphone Volume Button Right Button VO Connector Navigation Keys Back Panel Battery Door St lus Slot y IRDA Port D Image Scan Engine Window Left Button Stylus Fastener Memory Card Socket Flashlight Camera Flash SIM Card Socket Battery Well Color Camera Available Keyboards 31 Key Numeric Keyboard 80 67 08 45 Key QWERTY Keyboard Install the Battery Pack The 9700 is shipped with the battery packaged separate from the unit Follow the steps below to install the main battery 1 Release the hand strap near the base of the terminal 2 Remove the battery door by releasing the door latch and pulling up with a hinging motion 3 Insert the battery into the battery well 4 Replace the battery door Apply pressure to engage the door latch Note The battery door must be installed prior to powering the unit 5 Reattach the hand strap 6 Connect the terminal to one of the 9700 series c
3. Honeywell Dolphin 9700 with Windows Mobile 6 5 Quick Start Guide Disclaimer Honeywell International Inc HII reserves the right to make changes in specifications and other information contained in this document without prior notice and the reader should in all cases consult Honeywell to determine whether any such changes have been made The information in this publication does not represent a commitment on the part of HII HII shall not be liable for technical or editorial errors or omissions contained herein nor for incidental or consequential damages resulting from the furnishing performance or use of this material This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated into another language without the prior written consent of HII Web Address www honeywellaidc com Trademarks Dolphin and HomeBase are trademarks or registered trademarks of Hand Held Products Inc or Honeywell International Inc Microsoft Windows Windows Mobile ActiveSync and the Windows logo are trademarks or registered trademarks of Microsoft Corporation Other product names or marks mentioned in this document may be trademarks or registered trademarks of other companies and are the property of their respective owners 2010 Honeywell International Inc All rights reserved Out of the Verify that the carton
4. The Dolphin s battery status is indicated at the top of the touch screen in the Navigation Bar The battery is charging The terminal is using an external power source The battery has full charge The battery has high charge The battery has a medium charge The battery has a low charge QAA Be The battery has a very low charge Charge the battery ActiveSync Communication To synchronize the host workstation and the Dolphin terminal ActiveSync 4 5 or higher must be installed and configured for the appropriate communication type on both devices Dolphin terminals ship with ActiveSync already installed Therefore you just need to connect the Dolphin terminal to the host workstation via Dolphin peripheral to initiate communication Note You can download the most current version of ActiveSync from www microsoft com We recommend use of Honeywell peripherals power N cables and power adapters Use of any non Honeywell peripherals cables or power adapters may cause damage not covered by the warranty Installing a Memory Card 10 Press the Power key to put the terminal in Suspend Mode Release the hand strap near the base of the terminal Remove the battery door and the battery Remove the protective cover over the memory socket Unlock the access door to the memory socket by sliding the door away from the serial number label located in the battery well Lift the door up to expo
5. harging peripherals to charge the main battery pack We recommend use of Honeywell Li lon battery packs N Use of any non Honeywell battery may result in damage not covered by the warranty Charging the Dolphin The initial charging time for the main battery pack is 6 hours and 8 hours for the internal backup battery Connect the terminal to one of the 9700 series charging peripherals to charge the main battery HomeBase AUX Battery Well Dock LED AUX Battery LED HomeBase Back Panel USB Port Serial Port DC Power Jack HomeBase LED Indicators Green The terminal is properly seated in the igi base Orange The auxiliary battery is charging Green The auxiliary battery has completed charging and is ready for use Serial Port Communication Red Serial data is being sent from the host device to the base Green Serial data is being sent from the base to the host device Orange Serial data is being sent in both directions at the same time USB Port Communication Green AUSBconnection is established with the host workstation Charging Communication Cable PowerAdapter Cable Host Device RS232 Connector LED Indicators The light emitting diode LED located at the top of the LCD display flashes and illuminates during resets scanning imaging and taking a picture This LED can be programmed by various software applications Battery Status Indicator
6. se the Socket Insert the microSD or microSDHC card into the socket Note Make sure the interface on the memory card is connected to the interface in the socket align the notch on the card with the notch of the socket Close and lock the access door by sliding the door toward the serial number label Replace the protective cover over the memory socket Install the battery and the battery door 11 Press and hold the RED TAB keys for approximately 5 seconds 12 The decode and scan LEDs flash for approximately three seconds as the terminal resets 13 When the reset is complete the Today screen displays Note Honeywell recommends formatting all SD cards before initial use 10 Installing a SIM Card 1 Press the Power key to put the terminal in Suspend Mode 2 Release the hand strap near the base of the terminal 3 Remove the battery door and the battery 4 Remove the protective cover over the SIM socket 5 Unlock the access door to the SIM socket by sliding the door away from the serial number label located in the battery well 6 Liftthe door up to expose the Socket 7 Insert the SIM card into the Socket Note Make sure the interface on the card is connected to the SIM Card interface in the socket align the beveled corner of the card with the beveled corner of the socket 8 Close and lock the access door by sliding the door toward the serial number label 9
7. the device without losing RAM data 1 Press and hold the RED TAB keys for approximately 5 seconds 2 The decode and scan LEDs flash for approximately three seconds as the terminal resets 3 When the reset is complete the Today screen displays Hard Reset Cold Boot A hard reset resets the operating system restores the terminal back to factory defaults and resets the terminal after a bootloader keyboard and kernel upgrade A 1 A hard reset erases all of the data stored in RAM memory and all RAM installed applications Press and hold the RED ENT keys for approximately 5 seconds The decode and scan LEDs light for approximately 3 seconds The terminal re initializes 15 Technical Assistance Contact information for technical support product service and repair can be found at www honeywellaidc com User Documentation Refer to www honeywellaidc com for detailed user documentation or for localized versions of this Quick Start Limited Warranty Refer to www honeywellaidc com warranty information for your product s warranty information 16 Honeywell Scanning amp Mobility 9680 Old Bailes Road Fort Mill SC 29707 www honeywellaidc com LATA 9 0

Honeywell Dolphin 9700 Quick Start Guide

Contents

Download Pdf Manuals

Related Search

Related Contents