SHARP HT-SL70 HT-SL75 Operation Manual
Contents
1. 4 Screw the wall mount angle to the wall as shown in the illustration Total screw is 4 pieces Wall mount angle screws x2 N lt 2 Wall surface screws x 2 Uy team lt Wall mount angle Uy 1 Fix the pattern paper to the wall in horizontal position as below Wall surface Pattern paper 2 Make a hole on the wall following the screw point marks on the pattern paper by using a drill 1 1 4 32 mm 3 8 8 9 mm Wall surface 3 Fix a wall mount plug not supplied into the hole using a hammer until it is flush with the wall surface 1 1 4 32 mm 3 8 8 9 mm co Wall surface Note Make sure all screws are fully tightened screws are not supplied Hi Installing the sound bar 1 Align the wall mount slot at the sound bar to the wall mount angle 2 Slot the sound bar into the wall mount angle 3 Fix them securely Wall surface Falling prevention Safety wires not supplied are useful to prevent the sound bar from falling off the table Loop the safety wires not supplied into each hole as shown and tie the safety wires to the LCD TV stand Placing the system Installation image Notes As the sound from the system is omni directional you can place the speaker anywhere you like However it is recommended to place it as close to the TV as possible The front panel of the speaker is not2. 5 16 160 mm Rated input 100 W Weight 3 75 Ibs 1 70 kg each power Impedance 4 ohms HT SL70 Dimensions Width 4 1 2 115 mm For 46 TV Width 6 5 16 160 mm Height 16 5 8 422 mm Dimensions Height 27 13 16 706 mm Depth 12 1 16 307 mm Depth 6 5 16 160 mm Weight 9 92 Ibs 4 50 kg Weight 2 09 Ibs 0 95 kg each For 52 TV Width 6 5 16 160 mm Dimensions Height 30 13 16 782 mm Depth 6 5 16 160 mm Weight 2 09 Ibs 0 95 kg each E 15
3. TV eo tv oF SE eo 3 J 70 Tv ot ee Groove to Grooya to neatly arrange _ _ ran ike the wire in Se ge QE Va wire in 1O oa lt Slotin the wire inside the groove or slit for better Wire arrangement E 3 To mount the sound bar on the wall 1 Fix the brackets to the holes as shown Model HT SL75 for 60 and 70 TV Model HT SL70 for 52 TV Suggestion of the sound bars and LCD TV arrangement Caution 4 Be careful not to d fix the bracket Ea upside down P w System preparation continued Caution Bevery careful to prevent the sound bar from falling when mounting on the wall Before mounting check the wall strength Do not put on the veneer plaster or whitewashed wall The sound bar may fall If unsure consult a qualified service technician Mounting screws are not supplied Use appropriate ones Check all wall mount angle screws for looseness Select a good location If not accidents may occur or the sound bar may get damaged SHARP is not responsible for accidents resulting from improper installation Do not let children dangle on the sound bar once it is attached on the wall as it can cause damage and injury E Driving screws SHARP designed the sound bar so you may hang them on the wall Use proper screws not supplied See below for size and type 1 8 3 2 mm 3 8 9 mm gt 7 8 Min 22 mm Fixing wall mount angle
4. manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus A When a cart is used use caution when moving the cart apparatus combination La to avoid injury from tip over Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Additional Safety Information 15 16 Power Sources This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company For product intended to operate from battery power or other sources refer to the operating instructions Overloading Do not overload wall outlets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock 17 Object and Liquid Entry Never push objects of any kind 18 19 20 21 22 23 24 E 3 gt gt gt gt into this product through openings as they may touch dangerous voltage points or short out pa
5. supplies and consumable if any items Where to Obtain Service At a Sharp Authorized Servicer located in the United States To find a location of the nearest Sharp Authorized Servicer call Sharp toll free at 1 800 BE SHARP What to do to Obtain Service Ship prepaid or carry in your Product to a Sharp Authorized Servicer Be sure to have Proof of Purchase available If you ship the Product be sure it is insured and packaged securely TO OBTAIN SUPPLY ACCESSORY OR PRODUCT INFORMATION CALL 1 800 BE SHARP SHARP ELECTRONICS CORPORATION Sharp Plaza Mahwah New Jersey 07495 1163 Precautions E General Please ensure that the equipment is positioned in a well ventilated area and ensure that there is at least 4 10 cm of free space along the sides top and back of the equipment 4 10cm 4 10 cm 4 10 om ya 10 cm Use the unit on a firm level surface free from vibration Keep the unit away from direct sunlight strong magnetic fields excessive dust humidity and electronic electrical equipment home computers fax machines etc which generate electrical noise Do not place anything on top of the system x Do not expose the unit to moisture to temperatures higher than 140 F 60 C or to extremely low temperatures If your system does not work properly disconnect the AC power cord from the AC outlet and replug In case of an electrical storm unplug the unit for safety Hold the
6. If problem occurs during operation When this product is subject to strong external interference mechanical shock excessive static electricity abnormal supply voltage due to lightning etc or if it is operated incorrectly it may malfunction If the unit is not restored in the previous operation unplug and plug in the unit again or unplug all component connected and plug in again Maintenance Hi Cleaning the cabinet Periodically wipe the cabinet with a soft cloth Caution Do not use chemicals for cleaning gasoline paint thinner etc It may damage the cabinet finish Do not apply oil to the inside of each component It may cause malfunctions Specifications As part of our policy of continuous improvement SHARP reserves the right to make design and specification changes for product improvement without prior notice The performance specification figures indicated are nominal values of production unit There maybe some deviations from these values in individual unit E General Hi Soundba r speaker Type Full Range speaker system 7 8 x 4 1 2 2 2 x 11 5 cm Full Range Power source AC 120 V 60 Hz Power consumption 40 W Output power RMS Total 200 watts RMS Front Left Right 50 watts per channel into 3 ohms at 1 kHz 10 total harmonic distortion Subwoofer 100 watts per channel into 4 ohms at 100 Hz 10 total harmonic distortion FTC F
7. J iG Notes Connecting via this method may disable TV internal speakers Insome cases a small background noise could emit from the sound bar when you use the headphone connection with a TV Set In such case please change the connection to the HDMI ARC or RCA connection This effect depends on the used TV Brand model and age and it is not a quality matter from the sound bar 2 Method 2 TV To audio output terminal RCA cable Subwoofer Audio signal To AUDIO IN TV input terminal Note To control the volume some setting in the TV MENU is needed For details refer to the operation manual of the TV Example Go to the Setting Menu of the TV select AUDIO OUT and choose VARIABLE However if this does not work please use method 1 General Control Make sure to enable the HDMI CEC when making HDMI connection For details refer to the operation manual of the TV E To turn the power on Plug the AC power cord into a AC outlet the stand by indicator turns RED This unit will automatically power on if 1 TV or similar component which supports HDMI CEC is turned on 2 Audio signal is detected from Audio input The stand by indicator will turn BLUE if TV signal is detected Notes HDMI input will override the Audio input signal Audio input will function only when there is no signal from HDMI input A slight audio delay after TV is turned ON does not mean t
8. REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE FOR YOUR RECORDS For your assistance in reporting this unit in case of loss or theft please record below the model number and serial number which are located on the rear of the unit Please retain this information Model number Serial number Date of purchase Place of purchase NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance wi
9. removable Caution Do not change the installation direction when the unit is turned on Hi Placing the stand Place the stand as shown BD Player DVD player Place the system as shown Remove the protective film covering the sound bar and subwoofer before using the system System connections Make sure to unplug the AC power cord before making any connections Subwoofer Sound Bar ae AC outlet AC 120 V 60 Hz CAUTION TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE SLOT FULLY INSERT Hi Speaker connection Connect the wire without insulation tube to the minus Do not make a mistake when terminal and the wire with red and white insulation tube to connecting the right and left lt the plus terminal speakers The right speaker is the one on the right side when you face un Cautisn the unit lt auton Do not let the bare speaker wires Ez Use speaker with an impedance of 3 ohms or more as touch each other lower impedance speaker can damage the unit i Donotallow any objects to fall into or o to be placed in the bass reflex duct INCORRECT Do not stand or sit on the subwoofer soun
10. AC power plug by the head when removing it from the AC outlet as pulling the cord can damage internal wires The AC power plug is used as a disconnect device and shall always remain readily operable Do not remove the outer cover as this may result in electric shock Refer internal service to your local SHARP service facility This unit should only be used within the range of 41 F 95 F 5 C 35 C Warnings The voltage used must be the same as that specified on this unit Using this product with a higher voltage other than that which is specified is dangerous and may result in a fire or other type of accident causing damage SHARP will not be held responsible for any damage resulting from use of this unit with a voltage other than that which is specified To prevent fire or shock hazard do not expose this appliance to dripping or splashing No object filled with liquids such as vases shall be placed on the apparatus Controls and indicators Hi Sound bar FRONT VIEW REAR VIEW The spec label illustration may gt be different from the actual 4 5 label used OR eee cl j x LoLe SHARP moer no HT SL70 H E r i a i SOUND BAR HOME THEATER ATE
11. M e AT FULLRANGEKA 8 J SHARP CORPORATION TSPC BA7SAWZZ MADE IN MALAYSIA FABRIQUE EN MALAISIE 1 Left Front Speaker 2 Right Front Speaker 3 Bass Reflex Duct Reference page 4 Right Front Speaker Terminal Red Black 10 5 Left Front Speaker Terminal White Black 10 L Subwoofer FRONT VIEW Reference page 1 Stand by Indicator 2 Bass Reflect Duct 3 Woofer 4 HDMI TV ARC Output Terminal REAR VIEW The spec label illustration may be different from the actual label used N Reference page 5 HDMI Input Terminal 0 005 11 6 AC Power Cord 00 cece eee eee 10 7 Speaker Terminal 00 0000 eeeueee 10 12 8 Audio In TV Terminal System preparation Make sure to unplug the AC power cord before installing the unit or changing the position Select from three installation methods according to the preferred position 1 Using stand horizontal arrangement For 52 60 or 70 TV sound bar assembly Use Sound bar cover joint short 369 mm For model for 60 TV HT SL75 Use Sound bar cover joint long 594 mm for 70 TV For model Use Sound bar cover joint long 188 mm HT SL70 for 52 TV 1 Pull out both joint covers as below Sound bar joint 2 Place the two sound bars near to each other and slot in the sound bar joint and its covers as below F
12. SHARP MODEL HT SL70 HT SL75 SOUND BAR HOME THEATER SYSTEM OPERATION MANUAL Thank you for purchasing this SHARP product To obtain the best performance from this product please read this manual carefully It will guide you in operating your SHARP product HT SL70 and HT SL75 Sound Bar Home Theater system consisting of Sound Bar and Subwoofer ENERGY STAR HUM HIGH DEFINITION MULTIMEDIA INTERFACE Notes This product is recommended for flat panel TV LCD and plasma For HDMI connection this product only supports PCM Pulse Code Modulation signals This product is controlled via HDMI CEC Consumer Electronics Control specification therefore for HDMI connection your TV s CEC must be enabled For detail refer to the operation manual of the TV For TV without HDMI CEC headphone or RCA variable output analogue connection is available For TV without HDMI headphone or RCA variable output connection is required This unit supports HDMI which enables Audio Return Channel ARC Recommended Connection TV Type CEC FUNCTION CONNECTION CONNECTION METHOD HDMI HDMI IN with ARC MUST BE ENABLED ARC Page 11 Method 1 with HDMI MUST BE ENABLED HDMI IN Page 11 Method 2 HDMI TV without HEADPHONE OUT Page 12 Method 1 CEC amp ARC or non NONE RCA HDMI TV VARIABLE OUT Page 12 Method 2 MOA Pinte in Malesia TINSZB042AWZZ SHARP CORPORATION 11K R MWA Acce
13. d bar You may be injured System connections continued Hi Connecting to TV with HDMI Caution Turn off all other equipment before making this connection Set the TV at low volume before turning on the system Notes This unit supports HDMI which enables ARC Audio Return Channel To enable ARC make sure to use High Speed HDMI cable with ARC This ARC feature requires TV that supports ARC Refer the operation manual of the TV to determine which terminal supports ARC To listen to the sound from a non ARC compatible TV connect the audio output from TV to this system s AUDIO IN TV terminal refer page 12 This unit can be operated power on off or volume up down via a TV or similar component which supports HDMI CEC Consumer Electronics Control If this does not work it does not mean this system is faulty Refer to the operation manual of the respective component on how to activate the CEC Example Go to the Menu of the component to search and enable the CEC Different brands may have different naming for the CEC For Sharp LCD TV it is named as AQUOS LINK To listen to the sound from this system you will need to adjust settings within the TV menu For details refer to the operation manual of the TV If you are unable to select external speaker setting from the TV menu E g For Sharp LCD TV it is named as AQUOS AUDIO SP turn the CEC OFF and ON again Make sure the LCD TV Audio output setting is s
14. d described herein on behalf of Sharp The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser Correction of defects in the manner and for the period of time described herein shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product and shall constitute full satisfaction of all claims whether based on contract negligence strict liability or otherwise In no event shall Sharp be liable or in any way responsible for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage Some states do not allow the exclusion of incidental or consequential damages so the above exclusion may not apply to you THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE Model Specific Section Your Product Model Number amp Description HT SL70 HT SL75 Sound Bar Home Theater System Be sure to have this information available when you need service for your Product Warranty Period for this Product One 1 year parts and labor from the date of purchase Additional Item s Excluded from Warranty Coverage Non functional accessories
15. et to PCM not other formats such as Dolby Digital DTS etc To enjoy 3D images this system must be connected to a 3D compatible TV and components 3D BD player etc via High Speed HDMI cables Put on the 3D glasses otherwise 3D images may not be viewed properly Select from the 2 methods below 1 Method 1 This connection is for HDMI TV with ARC Audio Return Channel TV Subwoofer 1 DVD BD player or similar ToHDM f ARC e terminal To HDMI output terminal To HDMI output terminal Notes Refer to the operation manual of the equipment to be connected Fully insert the plugs to avoid fuzzy pictures or noises 2 Method 2 This connection is for HDMI TV without ARC Audio Return Channel Subwoofer DVD BD player To HDMI terminal TV or similar M i m To audio output terminal Ss TO HDMI HDMI OUTPUT input terminal f Notes To HEADPHONE terminal To listen to sound via TV turn off your connected DVD player or BD player or similar component Connecting via this method may disable TV internal speakers E 11 System connections continued Hi Connecting a TV with AUDIO IN TV Connect to the TV using an audio cable 1 Method 1 TV To HEADPHONE terminal os Audio cable Subwoofer E dD n 2 ke Ea Eu To AUDIO IN TV input terminal
16. harp brand product the Product when ship in its original container will be free from defective workmanship and materials and agrees that it will at its option either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period s set forth below This warranty does not apply to any appearance items of the Product nor to the additional excluded item s set forth below nor to any Product the exterior of which has been damaged or defaced which has been subjected to improper voltage or other misuse abnormal service or handling or which has been altered or modified in design or construction In order to enforce the rights under this limited warranty the purchaser should follow the steps set forth below and provide proof of purchase to the servicer The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD S FROM THE DATE OF PURCHASE SET FORTH BELOW Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein or to extend the duration of any warranties beyond the time perio
17. hat the system is faulty This is normal AQUOS speaker is enabled message will be displayed if SHARP LCD TV does not detect HT SL70 HT SL75 during power on However the message AQUOS audio with AQUOS LINK is enabled will be displayed soon as HT SL70 HT SL75 is detected These messages may vary for other TV model HM Audio Return Channel ARC Audio Return Channel submenu The Audio Return Channel ARC enables an HDMI ARC capable TV to send the audio stream to the HDMI OUT terminal of the receiver To use this function your TV must support the ARC Make sure the LCD TV Audio output setting is set to PCM not other formats such as Dolby Digital DTS etc For details refer to the operation manual of the TV E Volume Volume can only be controlled from your TV E Power Off This unit will automatically go to stand by mode indicator turns RED if 1 TV or similar component which supports HDMI CEC is turned off 2 No signal from Audio input is detected after 20 minutes Troubleshooting chart Many potential problems can be resolved by the owner without calling a service technician If something is wrong with this product check the following before calling your authorized SHARP dealer or service center E General Symptom Possible cause Nosound is heard Is the input signal selection set properly Is HDMI compliant equipment being used Is the HDMI cable con
18. nected correctly Is the HDMI cable of the correct type being used with ARC Does the sound input support PCM signal Do not connect or disconnect an HDMI cable while power is on This may lead to operation problems Noise is heard Move the speaker away during playback from any computers or mobile phones The power is not Is the unit unplugged turned on The protection circuit may be activated Unplug and plug in the power cord again after 5 minutes or more Volume cannot be Check if the HDMI CEC is controlled enabled For headphone or RCA TV setting VARIABLE is required 3D images not Depending on the TV and displayed on the TV Video component 3D images may not be displayed Check the operation manual of the respective component Background noise Please change to HDMI appears when ARC or RCA Output connecting with terminal from TV Set This headphone output of effect may occur TV Terminal depending on your used TV Brand model and age and it is not the sound bar problem Hi Condensation Sudden temperature changes storage or operation in an extremely humid environment may cause condensation inside the cabinet Condensation can cause the unit to malfunction If this happens leave the power on until normal playback is possible about 1 hour Wipe off any condensation on the transmitter with a soft cloth before operating the unit E
19. ng be sure to install the product according to the method recommended by the manufacturer Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal Protective Attachment Plug The product is equipped with an attachment plug having overload protection This is a safety feature See Instruction Manual for replacement or resetting of protective device If replacement of the plug is required be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug Stand Do not place the product on an unstable cart stand tripod or table Placing the product on an unstable base can cause the product to fall resulting in serious personal injuries as well as damage to the product Use only a cart stand tripod bracket or table recommended by the manufacturer or sold with the product When mounting the product on a wall be sure to follow the manufacturer s instructions Use only the mounting hardware recommended by the manufacturer For U S customer only CONSUMER LIMITED WARRANTY SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this S
20. properly handled This product has been engineered and manufactured with the highest priority on safety However improper use can result in electric shock and or fire In order to prevent potential danger please observe the following instructions when installing operating and cleaning the product To ensure your safety and prolong the service life of this product please read the following precautions carefully before use 10 11 12 13 14 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the
21. ront Left Right Minimum 35 watts per channel into 3 ohms at 200 Hz to 20 kHz 1 total harmonic distortion Subwoofer Minimum 93 watts per channel into 4 ohms at 100 Hz 1 total harmonic distortion Output HDMI with Audio Return Channel terminal output audio video support to 1080p x1 Input Analog input Audio in terminal Stereo mini jack 3 5 mm Input impedance 33 kohms HDMI input audio video support to Maximum 100 W CH input power Rated input 50 W CH power Impedance 3 ohms CH 4 pieces parallel HORIZONTAL SETTING HT SL75 For 60 TV Width 54 17 32 1385 mm Dimensions Height 1 26 mm Depth 1 31 32 50 mm Weight 2 74 Ibs 1 25 kg For 70 TV Width 63 3 8 1610 mm Dimensions Height 1 26 mm Depth 1 31 32 50 mm Weight 2 95 Ibs 1 34 kg HT SL70 For 46 TV Width 40 3 16 1071 mm Dimensions Height 1 1 32 26 mm Depth 1 31 32 50 mm Weight 2 54 Ibs 1 15 kg For 52 TV Width 47 13 32 1204 mm Dimensions Height 1 1 32 26 mm Depth 1 31 32 50 mm Weight 2 65 Ibs 1 20 kg VERTICAL SETTING 1080p x 1 HT SL75 For 60 TV Width 6 5 16 160 mm imensions Height 34 27 32 mm Mm Subwoofer Depth o EA i Type Subwoofer system Weight 3 75 Ibs 1 70 kg each 6 5 16 16 cm woofer Eor eA Hegn A A r Depth 6
22. ront side of the sound bar For 46 TV sound bar assembly For model HT SL70 1 Sound bar joint short Use Sound bar cover joint short 55 mm for 46 TV Pull out the joint cover as below E 7 2 Place the two sound bars adjacent to each other and slot in the sound bar joint and its cover as below Front side of the sound bar To fix the sound bar stand 1 Peel off the double sided tape separator and attach the sound bar stand cushion at the bottom surface of the sound bar stand Sound bar stand cushion Sound bar stand Double sided tape separator Hook 2 Fix the sound bar stand as shown Note Sound bar stand can be removed by pulling it off backward from the sound bar Suggestion of the sound bars and LCD TV horizontal arrangement System preparation continued 2 Using stand vertical arrangement For model Use sound bar stand cover 10 2 16 257 mm HT SL75_ Use stand base 13 7 32 336 mm For model Use sound bar stand cover 6 3 32 155 mm HT SL70 Use stand base 6 15 16 176 mm 1 Pull out the cover of sound bar stand as below Sound bar stand cover 2 Slot in the sound bar into the sound bar stand and fix its cover as shown 3 Slot in the sound bar to the base stand according to your TV size For model HT SL70 For model HT SL75 ag Tvd F 52
23. rts that could result in a fire or electric shock Never spill liquid of any kind on the product Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the AC cord or plug is damaged b If liquid has been spilled or objects have fallen into the product c If the product has been exposed to rain or water d If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation e If the product has been dropped or damaged in any way and f When the product exhibits a distinct change in performance this indicates a need for service Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards Safety Check Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition Wall or ceiling mounting When mounting the product on a wall or ceili
24. ssories The following accessories are included This product has no remote control RCA to Headphone Subwoofer Stand x2 Audio Cable x 1 HDMI Cable x 1 Wall Mount Cable 1pin 2 pins x 1 GITAUA004AW01 QCNWGA062AWPZ QCNWGAO065AWPZ Bracket x 2 QCNWGA064AWPZ LHLDZA267AWSA LY eS U amp I Sy SSS Wall Mount Pattern Paper Speaker Wire Sound Bar Stand x 2 Screw for Sound Bar Stand Angle x 2 For HT SL75 only For HT SL75 only GITAUA012AW01 Brackets x 6 Cushion x 2 LANGKA225AW01 TCAUHA028AWZZ QCNWHA046AW01 XEBY830P08000 PCUSSA190AWZZ For HT SL70 only For HT SL70 only TCAUHA027AWZZ QONWHA043AW01 For HT SL75 only D eO A 14 45 El e s 32 G g E a bl fe L j i g amp R o z A ej jal a 8 8 N o 8 o i Q Q m Sound Bar Cover Joint Sound Bar Cover Joint Stand Cover x 2 Stand Base x 2 for 60 TV short x 1 for 70 TV long x 1 GCOVAA330AW01 GDAI A016AW01 GCOVAA331AW01 GCOVAA333AW01 For HT SL70 only aE oF Ss BE on TR ot Sound Bar Cover Joint Sound Bar Cover Joint Stand Cover x 2 Stand Base x 2 for 46 TV short x 1 for 52 TV long x 1 GCOVAA306AW01 GDAI A013AW01 GCOVAA300AW01 GCOVAA302AW01 The illustrations printed in this operation manual are for the model HT SL70 Special Notes CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO
25. th the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help WARNING FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user s authority to operate this equipment ENERGY STAR Program Information Products that have earned the ENERGY STAR are designed to protect the environment through superior energy efficiency ENERGY STAR ENERGY STAR is a U S registered mark HDMI the HDMI Logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries Important Safety Instructions Electricity is used to perform many useful functions but it can also cause personal injuries and property damage if im
Download Pdf Manuals
Related Search