EXTECH Pen Multimeter with Voltage Detector 381676 User Guide
Contents
1. lead is fully retracted 2 Disconnect the common negative test lead from the bottom of the meter a 3 Put the function switch to NCV position AD 4 Test the detector on a known live circuit eE J 5 Hold the top of the meter very close to the AD voltage source as shown 6 Adjust the sensitivity dial to the highest sensitivity position fully counter clockwise and then lower the sensitivity as required 7 If voltage is present the light at the top of the meter will flash and the alarm will sound 4 381676 V2 0 06 06 AC VOLTAGE MEASUREMENTS WARNING Risk of Electrocution The probe tips may not be long enough to contact the live parts inside some 240V outlets for appliances because the contacts are recessed deep in the outlets As a result the reading may show 0 volts when the outlet actually has voltage present Make sure the probe tips are touching the metal contacts inside the outlet before assuming that no voltage is present CAUTION Do not measure AC voltage if a motor on the circ g switched ON or OFF Large surges may occur that can damage the meter 1 Set the function dial to the V position 2 Use the FUNC button to select AC 3 Insert the black test lead banana plug into the negative jack at the bottom of the meter 4 Unscrew the retracting nut clockwise to draw out the positive test lead 5 Touch the black test probe tip to the neutral side of the circuit 6 Touch the posit2. AC 3 381676 V2 0 06 06 Operating Instructions WARNING Risk of electrocution High voltage circuits both AC and DC are very dangerous and should be measured with great care NOTE On some low AC and DC voltage ranges with the test leads not connected to a device the display may show a random changing reading This is normal and is caused by the high input sensitivity The reading will stabilize and give a proper measurement when connected to a circuit NOTE The supplied black test leads standard test lead and alligator clip probe have protective plugs that must be removed before being inserted in the bottom of the meter The protective apparatus must be removed from the end of the lead that plugs into the meter NON CONTACT AC VOLTAGE DETECTOR WARNING Test the AC voltage detector on a known live circuit before each use WARNING Before using the meter in the AC Voltage Detector mode verify that the batteries are fresh by confirming characters appear on the LCD when the function dial is turned to the voltage V position Do not attempt to use the meter as an AC Voltage Detector if the batteries are weak or bad With the function switch set to the NCV position this instrument can detect the presence of AC voltage from 50 to 600VAC simply by being held very near to a voltage source The NCV function works when the meter s function dial is placed in the NCV position only 1 Ensure that the retractable test
3. C to 60 C Max 80 up to 87 F 31 C decreasing linearly to 50 at 104 F 40 C lt 80 6560ft 2000meters operating 3 90z 110g 8 2 x 1 5 x 1 1 208 x 38 x 29mm For indoor use and in accordance with the requirements for double insulation to IEC1010 1 1995 EN61010 1 1995 Overvoltage Category III Pollution Degree 2 9 381676 V2 0 06 06
4. User s Guide EXT INSTRUMENTS Pen Multimeter with Voltage Detector Model 381676 C 40193130 JOVI OA WSLGWIET AN Nd Introduction Congratulations on your purchase of the Extech Model 381676 This instrument provides AC DC Voltage Resistance Diode amp Continuity testing plus a built in non contact Voltage Detector Proper use and care of this meter will provide many years of reliable service Safety damage to the meter Follow all safety guidelines presented in this manual and the usual safety precautions used when working with electrical circuits This meter has been designed according to IEC 1010 with respect to electronic measurement instrumentation with an overvoltage category CAT III 600V and pollution 2 Preliminary Safety When using the meter observe all normal safety rules concerning e Protection against the dangers of electrical current e Protection of the meter against misuse When the meter is delivered check that it has not been damaged in transit When checking voltage always test the meter on a known live circuit first Test leads must be in good condition Before use verify that the test lead insulation is intact and free from lead wire exposure or other damage Use only the supplied test leads WARNING Improper use of this device can result in electric shock or Safety During Use e Be sure to set the appropriate function and range before use e Never exce
5. d at the top of the meter clockwise to completely draw out the positive test lead probe 5 Touch the test probes to the diode under test 6 A good diode will indicate approx 0 3V germanium diodes to 0 7V silicon diodes for the forward test and OL for the reverse test re A shorted diode will indicate the same value of voltage in both the reverse and forward test directions An open diode will indicate OL in both test directions 6 381676 V2 0 06 06 DATA HOLD Button To freeze a displayed reading press the DATA H button The reading will freeze and the aH display icon will be visible on the LCD To release the display press the DATA H button again The DH indicator will switch off and the display will again show real time readings MAXIMUM HOLD Button To display only the highest reading press the MAX H button The uM display icon will be visible on the display while in the Max Hold mode Now the display will only change when a higher reading than the displayed reading is encountered To return to normal operation press the MAX H button again the MH display icon will switch off FUNC Function BUTTON The FUNC function button is used to select AC or DC while in the VOLTAGE V mode The FUNC button is also used to select diode Continuity or Resistance Q while in the Q mode RANGE Button The meter automatically selects the optimum range however the meter s ranges can be selected manuall
6. e indicates that the operator must refer to an explanation in the Operating Instructions to avoid personal injury or damage to the meter This symbol indicates that a device is protected throughout by double 1 insulation or reinforced insulation This symbol advises the user that the terminal s so marked must not be connected to a circuit point at which the voltage with respect to earth ground exceeds 600V C This symbol indicates compliance to the European Union directive 2 381676 V2 0 06 06 Controls and Jacks B Retractable positive test lead Test lead retracting nut Finger protection barrier Rotary function dial RANGE button FUNCTION button MAX HOLD button 10 DATA HOLD button O OSEO UT ron 11 Common negative test lead jack 12 LCD display Note The battery compartment is located on the rear of the instrument AC voltage detector and warning light Sensitivity adjustment for AC volt detector Display Symbols Audible Continuity V Volts gt Mo Da s d E T T Pt Diode function Q Ohms AG H fi fi kMQ Low battery DN Data Hold l LA LA LN nv m milli 10 volts DC Direct current k kilo 10 ohms AC Alternating current M Meg 10 ohms MJ Maximum Hold Max Input Limit Specification Measurement Input Limit Voltage DC or AC 200mV range 250VDC or AC All other ranges 6 00VDC or VAC Resistance Continuity and Diode 250VDC or V
7. ed the limits indicated in the specification table of this manual e Never touch probes test leads or alligator clip when connected to live circuit e Do not measure voltage on terminals that exceed 600V above earth ground e Always use caution when working with voltages above 60VDC or 30VACrms Keep fingers behind probe barrier when taking measurements e Never connect test leads across a voltage source while the rotary switch is in the resistance continuity or diode mode of operation e Never perform resistance continuity or diode tests on live circuits e When taking non contact voltage measurements ensure that the positive test lead is NOT exposed and that the negative common test lead is not connected to the bottom of the meter e Before changing functions using the rotary function dial be sure to disconnect the meter s test leads from any circuit under test e Never use the meter in an explosive environment or where dust dirt or steam exists e Never use the meter if the housing or battery compartment is open e Do not store meter in direct sunlight high temp humidity or condensation e If the equipment is used in a manner not specified by the manufacturer the protection provided by the equipment may be impaired e ALWAYS discharge filter capacitors in power supplies and disconnect the power when making resistance or diode tests Safety Symbols This symbol adjacent to another symbol terminal or operating devic
8. f the following guidelines are not followed the dependability of the meter can be compromised 1 KEEP THE METER DRY If it gets wet wipe it off and allow it to dry before use 2 USE AND STORE THE METER IN NORMAL TEMPERATURES Environmental extremes can shorten the life of the electronic parts and distort or melt plastic parts 3 HANDLE THE METER GENTLY AND CAREFULLY 4 KEEP THE METER CLEAN Wipe the case occasionally with a damp cloth Do not use chemicals cleaning solvents abrasives or detergents 5 USE ONLY FRESH BATTERIES OF THE RECOMMENDED SIZEITYPE 6 IF THE METER IS TO BE STORED FOR A LONG PERIOD REMOVE THE BATTERIES Battery Replacement WARNING To avoid electrical shock disconnect the test leads from any source of voltage before removing the battery cover Do not operate meter unless the batteries are in place The icon will appear when battery voltage is low Turn the Function dial to the OFF position Disconnect the negative common test lead from the meter Fully retract the positive test lead probe Remove the Phillips head screw at the rear center of the meter housing Remove the battery compartment cover to access the batteries Replace the two 2 1 5V AAA batteries observing polarity 8 Secure the battery compartment cover Warranty EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and workmanship for one year from date of shipment a six month limited warran
9. g 3 digits Resistance 2009 0 10 1 0 of reading 3 digits open circuit 2kQ 0 001kQ voltage 0 25V 20kQ 0 01kQ 1 09 ing 1 digi 00K 0 1kO 1 0 of reading 1 digit 2MQ 0 001MQ 20MQ 0 01MQ 1 0 of reading 5 digits Accuracy Notes Accuracy specifications consist of two elements e reading This is the accuracy of the measurement circuit e digits This is the accuracy of the analog to digital converter Accuracy is stated at 65 F to 83 F 18 C to 28 C and less than 75 RH General Specifications Diode Test Continuity Check Display Input Impedance Over range indication Auto Power Off Polarity Measurement Rate Low Battery Indication Batteries Operating Temperature Storage Temperature Operating Humidity Storage Humidity Operating Altitude Weight Size Safety Forward DC bias Current 1mA approx Reverse DC bias voltage 1 5V approx Overload protection 250VDC or ACrms Audible signal will sound if the resistance is less than 50Q Open circuit voltage 0 5V Overload protection 250VDC or AC 2000 count 0 to 1999 LCD 10MQ AC amp DC Voltage OL is displayed After 15 minutes approx of inactivity Automatic no indication for positive readings Minus sign for negative readings 2 times per second nominal I 41 is displayed to alert battery replacement Two 2 1 5V AAA batteries 41 F to 104 F 5 C to 40 C 4 F to 140 F 20
10. ing nut located at the top of the meter clockwise to completely draw out the positive test lead probe 5 Touch the test probe tips across the circuit or part under test It is best to disconnect one side of the part under test from the circuit so the rest of the circuit will not interfere with the resistance reading 6 Read the resistance on the display The meter automatically selects the optimum range or the user may manually select a range using the RANGE button AUDIBLE CONTINUITY CHECK WARNING To avoid electric shock never measure continuity on circuits that have a voltage potential 1 Set the function switch to the Q Pposition 2 Use the FUNC button to select the audible continuity mode 3 Insert the black test lead banana plug into the negative jack at the bottom of the meter 4 Carefully turn the test lead retracting nut LE located at the top of the meter clockwise to aoe completely draw out the positive test lead probe 5 Touch the test probe tips to the circuit or wire under test If the resistance is less than approximately 50Q the audible tone will sound If the circuit is open the display will indicate OL DIODE TEST Set the function switch to the Q Ptposition 2 Use the FUNC button to select the diode function gt t 3 Insert the black test lead banana plug into the negative common jack at the bottom of the meter 4 Carefully turn the test lead retracting nut locate
11. ive test probe tip to the hot side of circuit 7 Read the voltage on the display The meter automatically selects the optimum range or the user may manually select a range using the RANGE button DC VOLTAGE MEASUREMENTS CAUTION Do not measure DC voltages if a motor on the circuit is being switched ON or OFF Large voltage surges may occur that can damage the meter 1 Set the function dial to the V position 2 Use the FUNC button to select DC 3 Insert the black test lead banana plug into the negative jack at the bottom of the meter 4 Carefully turn the positive test lead retracting nut located at the top of the meter clockwise to completely draw out the positive test lead probe 5 Touch the black test probe tip to the negative side of the circuit 6 Touch the positive test probe tip to the positive side of the circuit 7 Read the voltage on the display The meter automatically selects the optimum range or the user may manually select a range using the RANGE button 5 381676 V2 0 06 06 RESISTANCE MEASUREMENTS WARNING To avoid electric shock disconnect power to the unit under test and discharge all capacitors before taking any resistance measurements 1 Set the function switch to the Q position 2 Use the FUNC button to select the resistance mode Q 3 Insert the black test lead banana plug into the negative jack at the bottom of the meter 4 Carefully turn the test lead retract
12. ty applies on sensors and cables If it should become necessary to return the instrument for service during or beyond the warranty period contact the Customer Service Department at 781 890 7440 ext 210 for authorization or visit our website at www extech com A Return Authorization RA number must be issued before any product is returned to Extech The sender is responsible for shipping charges freight insurance and proper packaging to prevent damage in transit This warranty does not apply to defects resulting from action of the user such as misuse improper wiring operation outside of specification improper maintenance or repair or unauthorized modification Extech specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and will not be liable for any direct indirect incidental or consequential damages Extech s total liability is limited to repair or replacement of the product The warranty set forth above is inclusive and no other warranty whether written or oral is expressed or implied NO OP ONE 8 381676 V2 0 06 06 Specifications Function Range Resolution Accuracy Non contact AC 50 to 600V NA Voltage detector NCV DC Voltage 200mV 0 1mV VDC 2 000V 1mV 20V 0 01V 0 7 reading 2 digits 200V 0 1V 600V 1V AC Voltage VAC 200mV 0 1V 40 400H2 2 000V Am 0 8 reading 3 digits 20V 0 01V 200V 0 1V 600V 1V 1 0 readin
13. y When using the RANGE button to manually select a range start with the highest range and then select successively lower ranges until the desired range is reached The decimal place will move with each press of the RANGE button Automatic Power OFF The meter is equipped with an automatic power off feature to preserve battery energy After 15 minutes of inactivity the meter will automatically turn off To turn the meter on again simply rotate the function switch to the desired function Support line 781 890 7440 Technical support Extension 200 E mail support extech com Repair amp Returns Extension 210 E mail repair extech com For the latest version of this User s Guide Software updates and other up to the minute product information visit our website www extech com For up to the minute product information visit our website www extech com Extech Instruments Corporation 285 Bear Hill Rd Waltham MA 02451 Copyright 2006 Extech Instruments Corporation All rights reserved including the right of reproduction in whole or in part in any form 7 381676 V2 0 06 06 Maintenance WARNING To avoid electrical shock disconnect the test leads from any source of voltage before removing the back cover or the battery cover WARNING To avoid electrical shock do not operate the meter until the battery cover is in place and fastened securely This meter was designed to provide years of dependable service However i
Download Pdf Manuals
Related Search
EXTECH Pen Multimeter with Voltage Detector 381676 User Guide