EXTECH HDV600 English user manual
Contents
1. x 2 HDV600 EU EN V2 6 2 12 Description Monitor NO Ot BQ Nis co 10 11 12 13 14 Probe connector Camera button Video button Rotate image button Display Zoom buttons Light intensity buttons Power Button Scroll buttons Selection buttons USB connector Microphone SD card slot Video output jack 15 16 Reset button AC adaptor connector Articulating Probe q1 me OF oe oN Articulation knob Articulation tension knob Articulating camera Light intensity buttons Power button AC Adaptor and extension cable sockets Carrying strap Wireless Transmitter 1 oP OS Probe Connector Light Intensity buttons Power button AC Adaptor and extension cable sockets Carrying strap Probe accessories 1 Anti snag tip Magnet 45 Mirror Camera Shaft Monitor connector TA 11 12 13 14 1516 HDV600 EU EN V2 6 2 12 Setup Battery Charging and Status Indication Note A fully charged battery will allow approximately 5 hours of continuous use 1 Turn the meter off and then connect the AC adaptor to charge the meter 2 After several hours turn the meter on The battery icon will indicate either A Fully charged gt gt gt B Charge in progress 1 I T I TTL lt 3 Ifthe battery is charged remove the AC adaptor and observe that the fully charged 4 bar icon A Tl appears If the battery icon indicates le2. Disposal Follow the valid legal stipulations in respect of the disposal of the device at the end of its lifecycle 9 HDV600 EU EN V2 6 2 12 Specifications Monitor LCD Screen Interface Recording medium SD memory Compression format Still image format Video Recording Format Video output Format Receiver Frequency Receiver Sensitivity Video System Data Audio type Tripod mount Battery Power adaptor Operating Storage Temperature Operating Humidity Max Dimensions W x D x H Weight Transmitter Frequency Data Video System Battery Power adaptor Unobstructed Effective Range Operating Storage Temperature Dimensions W D H Weight approx 14 5cm 5 7 active matrix 640x480 pixels Mini USB 1 1 and AV out SD Card 2GB maximum MPGE4 JPEG 640x480 AVI 640x480 NTSC and PAL 2 4GHz 87dBm SNR 42dB Fmod 15kHz NTSC PAL Video Audio Stereo On rear Accepts standard tripod screw 3 7V rechargeable Li Polymer 100 to 240V input 5VDC output 10 to 60 C 14 to 140 F 40 to 80 C 40 to 176 F 80 24 1 x 17 8 x 7 0cm 9 5 x7 x2 75 1474g 3 25lb 2 4GHz Video Audio NTSC PAL 3 7V rechargeable Li Polymer 100 to 240V input 9VDC output 10m 10 to 60 C 14 to 140 F 40 to 80 C 40 to 176 F 7 5 x 2 75 x 2 5 19 x 7 x 6 35cm 0 95lb 431g 10 HDV600 EU EN V2 6 2 12 Camera Composite Video Imaging Sensor CMOS Video Format NTSC Brightness Control
3. Connect the probe to the monitor Press the Power button to turn the monitor on 3 Maneuvere the probe into position to view the area to be examined The probe can be bent into the shape of the area to be examined Optimum focus distance is 2 to 6cm 0 79 to 2 3 4 Optimum focus distance is probe dependent but the typical range is 2 to 6cm Zoom Press the a or a zoom buttons to increase or decrease the display resolution from 1X to 2X Light Intensity Press and release the a or 3 buttons to increase or decrease the camera LED light intensity Note the camera LEDs become warm when set to maximum intensity Taking a Picture Press the Es button to take and store a picture into memory The icon will appear on the display when a picture is taken Recording a Video REC Press the button to start recording a video The 2g icons will appear on the display when a video is being recorded Press the button to stop the recording Audio will be recorded on the video via the microphone on the bottom of the monitor Note The bottom access cover must be removed for audio recording A The IP67 waterproof rating does not apply when the bottom panel access cover is removed Display Rotation Press the button to rotate the display 90 degrees Installing probe accessories Three accessories mirror anti snag tip and magnet are supplied with each probe Attach the accessory by unscrewing the probe ring and screwing on the at
4. Manual Lamp Type LED Interface Waterproof Capacity IP57 Operating Temperature Probes and Cameras 20 C to 70 C 4 F to 158 F Articulation 240 20 manual tip articulation Accessories Mirror magnet and anti snag Ball excluding 25mm diameter cables Part Number Description OD Length Camera Focus Distance HDV TX1 Articulating Semi Rigid 6mm 1m 640x480 2 to 6cm HDV WTX1 Wireless Articulating Semi Rigid 6mm 1m 640x480 2 to 6cm HDV TX2 Articulating Semi Rigid Cable 6mm 2m 640x480 2 to 6cm HDV WTX2 Wireless Articulating Semi Rigid 6mm 2m 640x480 2 to 6cm HDV 4CAM 1FM Macro lens Flexible 4mm 1m 320x240 2 to 6cm HDV 5CAM 1FM Macro lens Flexible 5 5mm 1m 640x480 2 to 6cm HDV 5CAM 3F Long depth of field Flexible 5 5mm 3m 640x480 6 cm to o HDV 5CAM 3FM Macro lens Flexible 5 5mm 3m 640x480 2 to 6cm HDV 5CAM 10F Long depth of field Flexible 5 5mm 10m 640x480 6 cm to o HDV 5CAM 1RM Macro lens Semi Rigid 5 5mm 1m 640x480 2 to 6cm HDV 5CAM 3R Long depth of field Semi Rigid 5 5mm 3m 640x480 6 cm to o HDV 5CAM 3RM Macro lens Semi Rigid 5 5mm 3m 640x480 2 to 6cm HDV 25CAM 10G Fiberglass 25mm 10m 640x480 6 cmto HDV 25CAM 30G Fiberglass 25mm 30m 640x480 6 cm to o Copyright 2012 Extech Instruments Corporation a FLIR company All rights reserved including the right of reproduction in whole or in part in any form www extech com HDV600 EU EN V2 6 2 12
5. User Guide EXTECH INSTRUMENTS A FLIR COMPANY High Definition VideoScope Model HDV600 g High Definition MZA 77 HDV600 E A Introduction Congratulations on your purchase of this Extech HDV600 series Video Borescope This instrument is designed for use as a remote inspection device It can be used to peer into tight spots record and playback real time video and images Typical applications include HVAC inspection automotive inspection cable routing and automotive boat aircraft inspection The monitor is designed with dual left or right handed controls for maximum flexibility and is available with a full line of accessories This meter is shipped fully tested and with proper use will provide years of reliable service Models and Descriptions HDV600 HDV610 HDV620 HDV640 HDV640W VideoScope Monitor only VideoScope w 1m flexible cable 5 5mm diameter VideoScope w 1m semi rigid cable 5 8mm diameter VideoScope w 1m Articulating semi rigid cable 6mm diameter VideoScope w 1m Wireless Articulating semi rigid cable 6mm diameter Note Additional probe lengths and configurations are available A list is available at the end of this guide A Cautions A The IP67 waterproof rating does not apply when the bottom panel access cover is removed A For the Articulating Probe do not operate the articulation knob with the probe in a coiled configuration This will damage the articulation controls
6. buttons on the monitor not by the buttons on the transmitter VUUUUUVUUUUUU 7 HDV600 EU EN V2 6 2 12 Viewing a Stored Photo or Video in the Display 1 Press the A button to access the pictures or videos in memory Each button press will step through the files with the file number appearing on the screen i e IMGO0005 2 Pictures will appear with the photo icon on the display 3 Videos will appear with the film icon on the display 4 To play a video select a video file and press the button The gt play icon will appear during playback Press the button again to pause playback The m pause icon will appear Viewing an Image or Video on a PC There are two methods to transfer stored files to a pc 1 Remove the SD card from the monitor and insert it into the SD reader in the pc 2 Connect the monitor to the pc with a USB cable Images are saved in JPG format and videos saved in AVI format Lio Misc Deleting stored Images or Videos 1 Press the A button to access the pictures or videos in memory 2 When the file to be deleted appears press the OK button and the DELETE YES NO box will appear 3 Press the A button to highlight YES and then press the OK button to delete the file 4 Press the ESC button to exit at any time without deleteing the file Video Output 1 Turn the monitor on and select PAL or NTSC to match the video monitor to be used under the VIDEO OUTPUT selection in t
7. he MENU screen and press OK 2 Insert the video cable into the VIDEO OUT socket on the bottom of the monitor Connect the other end of the cable into the VIDEO IN jack of a TV or other monitor 3 The unit will output a high quality video image 8 HDV600 EU EN V2 6 2 12 Reset button If the monitor becomes unresponsive due to an EMI field or other magnetic event use a paper clip or other pointed object to press the RESET button located on the bottom panel Rear stand The rear stand can be set to three positions Lower stored middle position for bench viewing and upper position for hanging FCC Information This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Battery Replacement The charging circuit is designed only for the lithium battery included with the meter The meter should be returned to one of our repair facilities for replacement Non approved lithium battery could cause damage to the instrument or hazard to the users You as the end user are legally bound Battery ordinance to return all used batteries and accumulators disposal in the household garbage is prohibited You can hand over your used batteries accumulators at collection points in your community or wherever batteries accumulators are sold
8. se the outer knob tension 6 In this mode light intensity is controlled by the buttons on the monitor not by the buttons on the transmitter 6 HDV600 EU EN V2 6 2 12 Wireless transmitter The wireless transmitter is intended for use in areas that are difficult to access or in situations when is hard to maneuver the probe with the display attached The probe can also be connected directly to the monitor using the patch cord Note The battery must be fully charged for wireless operation A weak battery may result in meter shut down Wireless Mode 1 Direct Mode 1 Connect the AC adaptor to the transmitter and charge the battery Attach the probe to the transmitter Press and hold the Power button for 4 seconds to turn the monitor on then select WIRELESS under the INPUT SOURCE selection in the MENU screen Press and hold the Power button for 4 seconds to turn the transmitter on The camera video will be transmitter to the monitor display Connect the AC adaptor to the transmitter and charge the battery Attach the probe to the transmitter Connect the patch cord between the transmitter and the monitor probe input connector Press and hold the Power button for 4 seconds to turn the transmitter on Press and hold the Power button for 4 seconds to turn the monitor on then select DIRECT under the INPUT SOURCE selection in the MENU screen In the direct mode light intensity is controled by the
9. ss than 4 bars turn the meter off and continue charging 5 Always wait for a full fully charged indication to maximize operation time and to maintain battery health Note The battery will not properly charge if the meter is on during the charging cycle Startup Insert the SD card into the bottom SD slot 2 Press the Power button to turn the monitor on The battery icon will briefly appear indicating the battery condition 3 Press OK to open the setup MENU 4 Press the A or Y button to scroll through the ace MENU selections SS DATE TIME SETUP 5 Press OK to open the highlighted selection LANGUAGE Press the A or Y button to scroll through the VIDEO FORMAT items in an open menu item AUTO POWER OFF 7 Press the A or Y buttons to increase or INPUT SOURCE decrease the selected value 8 After there has been a change press the OK button to save the change or the ESC button to exit without the change Note After 10 seconds of inactivity the Setup menu will exit without storing changes MENU Description DELETE ALL Erase all stored pictures and videos DATE TIME SETUP Set the date year month day time hour minute second and display on off LANGUAGE Set the menu display to any one of 21 languages VIDEO FORMAT Set the video output to NTSC or PAL format AUTO POWER OFF Set the APO to 5 10 15 30 minutes or DISABLE INPUT SOURCE Set Direct or Wireless 4 HDV600 EU EN V2 6 2 12 Operation
10. tachment P ee ee 5 HDV600 EU EN V2 6 2 12 Articulating probe The articulating probe with adjustable tip angle is used for improved viewing angles and optimum inspection when the probe is inserted into the inspection location The articulating probe is available in a direct wired or A wireless version Wireless version Note The battery must be fully charged for wireless operation A weak battery may result in meter shut down 1 Connect the AC adaptor to the transmitter and charge the battery 2 Press and hold the Power button for 4 seconds to turn the monitor on then select WIRELESS under the INPUT SOURCE selection in the MENU screen 3 Press and hold the Power button for 4 seconds to turn the transmitter on The camera video will be transmitted j y to the monitor display y me Insert the probe into the area to be inspected 5 Turn the probe outer knob to adjust the camera tip to the viewing angle needed 6 Turn the upper knob to increase or decrease the outer knob tension Direct version 1 Connect the probe to the monitor using the supplied patch cable 2 Press and hold the Power buttons for 4 seconds to turn the probe and the monitor on 3 Insert the probe into the area to be inspected 4 Turn the probe outer knob to adjust the camera tip to the viewing angle needed 5 Turn the upper knob to increase or decrea
Download Pdf Manuals
Related Search