Home

Infocus TD61 user manual

1. White Level gain All 130 Red O 126 Green C 131 Blue 130 set RGB levels manually display a black picture from the source puter Select Black Level and adjust it until one of the three colors just touches the 0 value Then adjust the other two colors until they just touch 0 also Do not push this value lower than 0 because the number will not change but the picture will get worse Now display a white picture from the source computer Select the White lev els and adjust them until the value just touches 255 Do not push them higher than 255 because the number will not change but the picture will get worse When the source is Analog 1 or 2 and has YPbPr colorspace See 3 3 What Does Colorspace Mean on page 34 If a color bar pattern is available in YPbPr turn on Blue Only and adjust Saturation by matching the two outer color bars adjust Hue by matching the inner two bars Input Levels Contrast P 9 Saturation 0215 125 Hue 133 Blue Only Restore Factory Defaults 61 Input Levels Digital Sources Picture Main Menu When the source is Digital and the colorspace is RGB See 3 3 What Does Colorspace Mean on page 34 1 The digital level controls are not often used because most digital sources don t need them Reset is a button that will return the system to the default values for digital sources
2. Warning The power cord and cables associated with this product contain lead a chemical known to the state of California to cause birth defects or other reproductive harm Wash hands after handling Warning This product has a lamp which contains a very small amount of mercury Dispose of it as required by local state or federal ordinances and regulations For more information see www elae org Contents 1 Introduction 3 1 1 About the TD61 4 1 2 Accessories for TD61 6 1 3 Using the Remote Control 8 1 4 Your Safety is Important 10 2 Installation 13 2 1 What You Will Do 14 2 2 Unpacking the TD61 16 2 3 Installing the TD61 18 2 4 Connecting Source Cables 20 2 5 Connecting 5232 5485 Cables 22 3 Adjusting 23 3 1 Aligning the Image 24 3 2 Adjusting TD61 To Its Source 28 3 3 What Does Colorspace Mean 34 3 4 Color Balancing TD61 36 3 5 Scaling and Cropping 38 3 6 Saving Your Work and Recalling a Memory 40 4 Operating 43 4 1 Normal Start Up 44 4 2 Reading the Aloha Numeric Display 4 3 Controlling TD61 with Remote 48 4 4 Controlling TD61 with RS232 R5485 Maintenance 51 5 1 Changing a Lamp 52 5 2 Changing the Air Filter 54 Reference Section 55 6 1 Remote Control Functions 56 6 2 Menus Structures 60 6 3 TD61 Drawings 84 6 4 Connector Wiring 86 6 5 Regulatory Information 88 6 6 Specificat
3. 1 77 The effective resolution of the TD61display i e the number of pixels visible on the screen is about 1232x693 pixels but may vary slightly from unit to unit The aspect ratio of a TD61 is 1 77 16x9 When the source picture s aspect ratio is not the same as the TD61 you have to do something to make the picture fit You have three basic choices Fill the area both ways This will produce some distortion in the picture Circles will not be round Put the picture in without distortion crop the top and bottom Put the picture in without distortion and fill the extra space with black A picture with an aspect ratio of 1 33 is shown Scale Mode Normal Video 4x3 Justify Center Overscan 0 Aspect Ratio Justify Center Overscan 0 38 Same picture Scale Mode Fill All Justify Grayed out Overscan 0 Aspect Ratio Overscan 0 Scale Mode determines how the picture will be made to fit the display e Fill All means that the picture will touch the bor ders of the display all around even if this means stretching and distorting the picture in one direction Letterbox Pillarbox means expand the picture until the first edges top bottom or left right touch the border of the display then fill in the other sides with black Crop means expand the picture until the second edges touch the border and let the other edges of the picture fall outside the display and get cropped Wi
4. 20 Connecting RS232 RS485 Cables 22 2 1 What You Will Do This is an overview of the entire installation and setup process The numbers in parentheses are page numbers in this User Guide where more detailed information is available Installation 1 Unpack the TD61 carefully 16 2 Hang the TD61 on a wall or optional stand 16 DO NOT lay the TD61 on its back or face 3 Connect the source cables Data Video Audio 20 4 Connect control cables if needed RS232 RS485 22 Connect Power 20 Turn on power switch 24 Press the on button on the remote control 44 CON WB Press the source button to select source 56 Configuration 1 Align the image 24 2 Adjust data input levels 30 3 Adjust frequency and phase 31 4 Adjust for video source 32 5 Adjust the image size 38 6 Save your settings 40 15 2 2 Unpacking the TD61 To avoid damaging the TD61 during unpacking it is advisable to read this section carefully 1 Remove the plastic plugs on either 2 Open the box top and find the accessories side of the bottom of the box inside Remove the accessories and the car board accessory holder You may want to install the wall mounting bracket from the accessory kit on a wall or optional stand before unpacking the rest of the way This would provide a safe place for the TD61 once 4 Slide the box sleeve up and off of the TD61 5 Lift the TD61
5. 709 Effective Resolution 1241 x 698 Engine Resolution 1280 x 720 Main Menu Picture Position Aspect Ratio Memory Audio Diagnostics y cw vw Program Information Advanced Options Color Balance b Miscellaneous Options gt Lamp Settings b Serial Port Settings Auto Setup Options Menu Options Image Alignment Pan Image Shrink Grow Resetto Default O Illuminate Border d 1 27 3 2 Adjusting TD61 To Its Source The source picture from computer video DVD is variable and does not always conform exactly to a standard TD61 has a way to compensate for this Connections The TD61 has 3 computer sources analog 1 ana log 2 and digital Analog 2 and digital sources share a connector This is an M1 connector Because they share a connector they also share a chip for EDID Extended Display Identification Data EDID is what tells a computer the type of monitor it is attached to It is the mechanism that allows Plug and Play moni tors to work Most of the time Plug and Play will work just fine but every once in a while EDID can get in the way of smooth operation TD61 has 2 user controls that deal with EDID Plug and Play Enable turns on EDID for both analog 1 and analog 2 digital Unchecking this box causes the host computer to ignore it The other user control allows the user to choose whether the EDID information on the M1 connector is for an analog monitor or a digital moni
6. contact 1 InFocus 2 a service facility authorized by InFocus or 3 the place of original purchase InFocus Customer Service 1 503 685 8888 or visit www infocus com service Warranty service will be provided at an InFocus authorized repair facility The purchaser must either deliver the Product to an authorized repair facility freight and all fees prepaid or pay for any travel and or transportation costs the service center may charge to and from the purchaser s location InFocus or the service facility authorized by InFocus will return the repaired replaced Product freight prepaid to the purchaser Products returned for Warranty service must be accompanied by a written letter that i explains the problem ii provides proof of date of purchase iii provides the dealer s name and iv provides the model and serial number of the Product Upon request of InFocus Corporation or an authorized repair center for InFocus proof of legal import must accompany the warranty repair Product otherwise the Product must be returned to the place of original purchase to the manufacturer Purchaser must bear all tax duty and freight or the Purchaser must bear charges for the warranty repair No repair or replacement of Product or part thereof shall extend the Limited Warranty period as to the entire Product Warranty on the repair part and workmanship shall only be effective for a period of ninety 90 days following the repair or replacement of that part or
7. the same memory location Color balance is the same for all sources When adjusting WHITE BALANCE ALL you may not see all three of the red green and blue numbers decrement or increment This because the ALL choice adjusts the colors in proportion to each other so that the color remains constant as you adjust the brightness For example if you have the color set at Red 100 Green 80 and Blue 40 and adjust down 10 clicks you will wind up with Red 90 green 72 and Blue 36 The color has remained the same and only the brightness has changed Green and blue did not change on every one of the ten clicks TD61 has a feature that allows a boost in the whites When this is on Color Balance will become more difficult but will allow for brighter whites lt The TD61 has a gamma control which allows the user to choose between Video and Film gamma in the color balance menu 100 Bright Changes in the White value moves this end point 0 0 Changes in the White values E affect the Gray values 5 0 2 Dark Black Writ Input Signal Changes in the Gray values do not affect the White values 2 E D 5 2 Changes in the Gray value move this mid point Input Signal 37 3 5 Scaling and Cropping Sometimes the picture does not fit the display The aspect ratio of the TD61 is 1 77 16x9 the same as HDTV amp The aspect ratio of a picture is its width divided by its height 1280 720
8. 1 Grade Scale Typical lt 0 2FL lt 20 24 Bits 100 0 305 0 335 0 650 0 330 0 320 0 640 0 145 0 080 6500 2 Grade Scale Notes Internal Black field test pattern Internal Black field test pattern Internal R G B field test pattern Total image non linearity is defined as a maximum of 5 pixels due to optical engine tolerances and 4 pixels due to chassis screen tol erances IFC Focus Pattern 2 meters from screen 9 locations 3 inputs to handle any selected source Buffered output of currently selecte input to drive headset or external amplifier 10W channel Environmental Specification Maximum Temperature operating 30 C 95 F non operating 50 C 122 F Altitude barometric pressure 10 000 ft Humidity 85 R H 92 Minimum 0 C 32 F 20 4 F 20 R H Typical Notes All performance specifications are maintained within this tempera ture range Above sea level or equivalent baro metric pressure 40 C non condensing Index Numbers 9 pin to RJ45 adapter 22 A AC power requirements 91 adapter RJ45 22 adapter RJ45 to 9 pin 22 address definition of 78 adjusting levels 30 levels manually for computer sources 61 levels semi automatic for computer sources 61 to computer sources 30 adjusting to computer source 30 adjusting to digital source 32 adjusting video with color bars 32 adjusting with color
9. ASCII Response Type Symbolic ASCII Response Terminator CR LF Baud Rate Terminate RS 485 19200 Baud rate Each display s baud rate must be set to the com puter or controller s baud rate The baud rate is not automatically established as it is in modems Terminating the series The displays in a group should not usually need termination however if you are experiencing prob lems try terminating the last display by going to MAIN MENU gt ADVANCED OPTIONS gt SERIAL PORT SETTINGS and checking the TERMINATE RS485 box at the bottom of the menu 5 Maintenance 5 1 Changing a Lamp 52 5 2 Changing the Air Filter 54 51 5 1 Changing a Lamp You will need a slot head screwdriver for this procedure TD61How to change the lamp 1 If you are changing the lamp for any other reason than it is dead use the remote control to turn off the lamp and allow it to cool down Allow the lamp to cool down for 15 minutes before remov ing 2 Turn off the AC power switch underneath the sig nal input panel on the back left of the TD61 and remove the power cord 3 Remove the right access panel by removing two 6x32 screws at the bottom of the panel and slid ing it to the right 4 Use screwdriver to loosen the captive screw hold ing the lamp in place 52 amp Note Guide pins are provided to insure the proper alignment of the lamp and the optical engine 6 Slide the new lamp into place a
10. COOL ING DOWN and a 45 second countdown will com mence At the end of the 45 seconds the lamp will turn on and the lamp fans will start if AUTO LAMP is on It shortens lamp life to turn it on when it is hot so the fans run for a minute or so to be sure it is cool If you have turned off the lamp using the remote control the TD61 will start a 45 second cool down During this time you cannot turn the lamp on At the end of the cool down period the alpha numeric display will say READY and you can now light the lamp using the remote control ON button The TD61 will then lock on to the last selected source To search for another source press the source button on the remote control After this cooling down period you can turn on the lamp Lamp Settings Lamp Saver Lamp Saver Timeout 2hr Lamp Saver Timeout Omin Shut down sequence When you turn off the lamp the fan will continues to run for a few minutes to cool the Lamp A CAUTION It is bad practice to turn off the TD61 by turn ing off the AC power The lamp does not cool properly This may shorten lamp life 44 45 4 2 Reading the Aloha Numeric Display The Alpha Numeric Display provides information on the status of the TD61 including failure informa tion in case the unit should not operate properly The Alpha Numeric Display is an LCD panel located on the bottom left of the TD61 It is an excellent resource for troubleshooting as well as providing sta tus i
11. Hz Horizontal Frequency 43 38 kHz Pixel Frequency 55 02 MHz Horizontal Resolution 1024 1 Vertical Resolution 768 3 Frequency 1344 ES Phase 4 29 34 Sharpness Sharpest Input Levels b This diagram shows the difference between the RGB and YPbPr signals or waveforms It is not nec essary to completely understand these waveforms However it should be clear that if the T D61 is set for one type say RGB and the signal is of the other type YPbPr the TD61 would process the color information incorrectly Picture t Colorspace YPbPr Component Video 2 2 Separate Vertical Frequency 60 Hz Horizontal Frequency 43 38 kHz Pixel Frequency 65 02 MHz F Horizontal Resolution 1024 1 Vertical Resolution 768 Frequency 1344 ES Phase 0 22 5 34 Sharpness Sharpest Input Levels b 35 3 4 Color Balancing TD61 3 4 Color Balancing TD61 Color Balancing can be done before or after Input Levels The object of color balancing is to make individual units show the same colors If we have more than one TD61 in a room we would like them to look the same When we see a red car on one of the TD61s it would be nice if it were the same shade of red on the other The displays naturally have slightly different colors from one display to the next because of slight varia tions in the optics This cannot be avoided but we can compensate for it with color balancing Color balancing is subjective
12. Input Levels When the source is Digital and the colorspace is YPbPr See 3 3 What Does Colorspace Mean on page 34 Input Levels amp For Analog Sources see page 61 amp For Video Sources see page 63 62 Inout Levels Video Sources Picture Main Menu When the source is Composite or S Video Input Levels The top items in the Input Levels menu when the source is video correspond to similar controls on television receivers although PAL and SECAM receivers do not use a hue control The Blue Only check box is for adjusting the picture with color bars from the source See 3 2 2 Adjusting to Video Sources on page 32 lt For Digital Sources see page 62 amp For Analog Sources see page 61 63 Position Main Menu 7 From the Main Menu select Position to Picture b access the Picture Position menu Aspect Ratio Memory Audio Diagnostics Advanced Options gt p gt gt 4 Program Information Picture Position Lise arrow keys to move image lt Horizontal Position 234 SOURCE PICTURE Vertical Position 34 CURTAIN SSIZE POS SAVE SETUP eei Press the SIZE POS to access the Position menu directly proie MONITOR MUTE VOLUME ag spl i MENU PREV ENTER Aspect Ratio 65 Main Menu Pict A Aspect Ratio Position b __ AspectRatio M Justify Audio Diagnos
13. It may seem strange at first but it gets easier with practice Fortunately you don t have to match all the colors you only have to match whites and grays When you make the displays look the same with White and Gray all the other colors will look the same It is not necessary to achieve a perfect white or a perfectly colorless gray It is only necessary that the displays look alike when they display white and gray amp Note Never try to match the colors of the display units with the Black and White Level controls or with the Video Controls You will not like the results if you do Color Balancing 1 Turn on the displays and let them warm up for at least five minutes The lamps must be thoroughly warm before you color balance 2 For each display access the color balance menu by pressing MENU on the remote control then select ing ADVANCED OPTIONS COLOR BALANCE 3 If color temperature is important you should first set the color temperature If it is not important start with the default 6500K which yields the brightest display At 6500K all the white balance values are set to 100 Once you start adjusting the color temperature will automatically change to custom 4 Set GAMMA at the bottom of the menu to either Video or Film but be sure this is the same for all displays 5 Set WHITE BOOST to OFF 6 Set TEST PATTERN to WHITE 36 amp Always use the internal Test Patterns for color balancing not an extern
14. a wall 1 Install wall mounting bracket bar on wall Make sure the wall mounting bracket is straight and level If the wall is uneven use shims to insure the wall mounting bracket is straight Be sure to attach to studs in the wall 2 Hang the TD61 on the wall mounting bracket bar Make sure the holes in the TD61 wall mounting bracket slot mate with the pins on the hangar bar eee 557 Wall mounting bracket installed Inset shows one of the two pins that mate with the holes in the slot in the back of the TD61 Back of TD61 showing wall mounting bracket slot Inset shows one of the two holes that mate with the pins on the wall mounting bracket Wall mounting bracket on wall TD61 being lifted in to place on the wall The slot fits over the wall mounting bracket and is fitted onto the mating pins Installing the Lower Retaining Bracket The lower retaining bracket is not designed to hold the weight of the display Its function is to hold the bottom of the display securely to the mounting surface and to allow adjustment of the display to insure perpendicu larity Attach the lower retaining bracket to the bottom of the display with the side of the angled bracket with the 4 slotted holes against the bottom of the display and the other side between the display and the mounting surface Mark on the mounting surface to locate the bottom and ends of the retaining bracket Remove the retaining
15. bracket from the display Remove the display from the mounting bracket Install the Lower retaining Bracket to the mounting surface with appropriate hardware and slots Locate the bracket on the mounting surface using the locating marks made when it was on the display Hang the display on the mounting bracket Secure the display to the lower retaining bracket leave the screws a little loose to allow for adjust ment Use the hardware provided Do not push or pull the display to align it with the slotted holes in the lower retaining bracket If the holes do not align remove the retaining bracket and repeat the steps to locate the bracket on the mount ing surface Use a level or plumb bob to determine perpendicu larity Move the bottom of the display either in or out till the display hangs perfectly straight Tighten the screws on the lower retaining bracket Lower retaining bracket installed on the bottom of the TD61 The adjustment slot is shown in the blow up picture Lower retaining bracket attached to mounting surface 19 2 4 Connecting Source Cables All of the TD61 signal inputs are on input modules housed in an electronic cage assembly accessible from the left side of the TD61 Analog and Digital Connectors There is one analog 15 pin VGA type connector and one standard M1 connector as data inputs to the TD61 The M1 connector also doubles as a second analog connector when used with a VGA to
16. image Horizontal een 234 VOLUME Vertical Position a4 Moves the image on the MONITOR MUTE VOLUME screen Main Monu PREV ENTER zi Y f Picture 00 Position Memory OD Audio gt Program Information gt 56 Display Status TD61 573 2200 Rev 1 0 Optical Engine SN 41034400100342 ID Tag PS Fan On Eng Fans On Lamp On Interlock ok Temperature 38 C Fault Override is On Mode ID 77 HPer 1742 Vines 806 Last Fault Interlock 0175 05 Serial Part Status RS 232 Press entiers 16 clear Commands Received 24 Replles Sent Last Packet Operation Last Packet Address This cube Bytes Received 231 Bytes Sent 25 UART Framing Errors 0 UART Overflow Errors 0 Group 0 Unit O 19200 Baud Mosi Recent D Serial Port Status RS 485 Press enter to clear Commands Received 24 Replies Sent 3 Last Packet Type Operation Last Packet Address This cube Bytes Received 231 Bytes Sent 25 UART Framing Errors 0 UART Overflow Errors 0 Group 0 Unit 0 19200 Baud Not Terminated Most Recent 0 Test Patterns Starts the process of scanning the input connectors for the next available source VOLUME proa MUTE VOLUME PREV ENTER None m Custom color gt White MC Gray Scale Grid M Red Red Scale Alignment Dashes e Green Green Scale 4x4 Checkerboard Blue K3 Bl
17. out of the box and remove the plastic Be sure that you have a safe place to stand the unit up It cannot be placed on its back or on its face 16 17 2 3 Installing the 61 The TD61 is meant to be installed on a wall or on an optional stand It is not designed to sit on its own Introduction The TD61 can be attached to a wall or to an optional stand Hardware for mounting is provided in the accessory kit Included in the accessory kit are two mounting bars The larger of the two is the main wall mounting bracket The smaller one is used as a spacer to keep the TD61 vertical when mounted on a wall or attached to a stand Mounting on a wall The TD61 weighs about 106 pounds 48 08kg The mounting method that you use must be able to support five times this weight 530lbs 240 4kg Make sure that the wall can support it Dry wall may not be sufficient to handle the weight The illustration on the right shows the wall mounting bracket installed on a wall The wall mounting bracket is firmly attached to the studs in the wall prevent the wall mounting bracket from bending due to the weight of the TD61 there must be bolts placed within 7 5 inches from each end The inset on the illustration highlights a pin on the main wall mounting bracket that mates with a hole in the slot on the back of the TD61 ZN CAUTION Do not lay the TD61 on its face or on its back It must be kept upright at all times Mounting TD61 on
18. that is black then one that is pure white With these you can quickly and automatically make the display learn what this computer means by black and white The result Good pictures using all the dynamic range of color coming from the computer amp For Input Levels you must use black and white coming from the computer you will use for the program You don t make this adjustment with your work laptop and then switch to another computer for the display s program of pictures What does Color Balance do Color balancing matches the colors between sev eral TD61 s Displays differ from one another because of very small differences in the color of the light produced by the lamp and by differences in the dyes used to make the color in a DLP optical engine In color balancing you use the display s internal test patterns of white then gray The internal pattern assures that a pure white is used 29 3 2 Adjusting TD61 To Its Source 3 2 1 Adjusting to Computer Sources Digital sources do not normally need adjustment The best way to adjust levels is the semi automatic method Adjusting levels semi automatically This is quick and easy if you can get a black pic ture and a white picture from the source computer 1 Display a black picture from the source This must come from the computer source that will be used for the program It does no good to use your laptop for this adjustment then connect to a dif ferent com
19. the background to change color Press MONITOR four times to open the Test Patterns menu E Focus Logo Custom Test Pattern Custom Test Pattern Color None when you are finished _ O x images These block any incom 71 72 Diagnostics Setup Summary Main Menu Diagnostics You cannot change anything in this menu It is for refer ence only The Setup Summary menu looks different for digital or video sources Slot is only visible when the current settings are exactly the ones in a numbered memory slot Setup Summary Diagnostics Ballast Ballast menu provides information only You cannot change anything from this menu Ballast Fault None Voltage 93 Y Temperature Zone 5 Pulse Plateau Ratio 2 81 Software Version 1544 Status Lamp on Pulse Syne Ballast Ballast Not Communicating Fault If a fault condition occurs the lamp will shut down However you will be able to query the ballast via RS232 to obtain the fault condition There are 9 fault conditions None Lamp over voltage Mains over voltage Temp too high Asymmetry detected voltage waveform to the lamp is asymmetrical Lamp under voltage Mains under voltage NTC defective temperature sensor for the ballast electronics e Sync frequency outside limits Voltage Plateau voltage to the lamp Temperature Zone There are 7 temperature zones reported by the ballast Driver shut
20. the slot selected To change the Name of a memory slot highlight Name and press ENTER A bar appears below the name which indicates character position Use the arrows to move the yellow highlight in this bar Use the up down arrows to change the character at that position There are 24 character spaces available The default name is an abbreviation of the memory con tents connector used resolution Save 117 Ll25 L 33 Mio 18 L126 O 34 111 119127 35 Press SAVE twice to M12 CI 20 O 28 36 open this menu 113 O 21 0 29 37 directly Ot 0 22 138 115 023 031 039 116 24 32 40 ENTER Save Save to Slot 1 Name AN1 1024x768 Source Analog RGB 1 Colorspace RGB Resolution 1024 x 768 Scale Justify Widescreen Center Position 328 4 Frequency Phase 1344 0 Sharpness Normal Black Level 52 50 104 O White Level 178 131 135 Volume Treble Bass 46 48 53 Mute Speaker Input O Channel 1 Balance Line Out Balance 50 50 Save Save to Slot 2 Save Now Source Analog RGB 1 Resolution 1024 x 768 Colorspace RGB Resolution 1024 x 768 Scale Justify Widescreen Center Position 328 4 Frequency Phase 1344 10 Sharpness Normal Black Level 52 50 104 O White Level 178 131 135 Volume Treble Bass 46 481 53 Mute Speaker Input O O Channel 1 Bal
21. the solder side These diagrams look at the outside of the connec tor as the cable sees it not the wiring side RS232 adapter DB15 standard VGA connector The wiring shown for this adapter is correct for straight thru network Black wire 2 cables Yellow wire 3 Green wire 5 1 DEL CNN CINC s eee RJ45 looking into the socket This little 9 pin to RJ45 adapter is available unwired from many computer or electronic stores Get one with a female 9 pin connector The RS232 cable must be wired straight thru You m SDA DDC can tell if a cable is wired straight thru by looking at 12 sap its two ends side by side 1 Hold the cable ends next to each other both ends dn TTL Vertical Sync pointing away from you Have the clips on both connectors pointing down so you can t see them SCL DDC 2 If the color of the wires on the two connectors is the same left to right the cable is straight thru The order of the colors doesn t matter as long as they are both the same 86 M1 Connector TMDS Data2 TMDS Data TMDS Data2 4shield NC NC DDC Clk DDC Data Analog VSync TMDS Datal TMDS Datal TMDS Data 1 3 Shield NC NC 5V Power 10 ci ED o S Video Connector Ground luminance Ground chrominance Luminance 1 V including sync ohms Chrominance 0 3 V burst 75 3 75 ohms Ca GND 5V Hsync Vsy
22. via an RJ45 RS485 output Display Technology The display technology is single chip DLP Service The TD61 is completely serviceable from the front All parts replacement should be performed at the module level by a qualified service technician 1 2 Accessories for TD61 The accessory kit for the TD61 contains the following items Each TD61 comes with quantity AC power cable 1 cable 1 e 8 32x3 8 Pan Head Phillips 2 screw 4 Wall Mounting Bar 1 Lower Retaining Bracket 1 Remote Control with batteries 1 Quick Start Card e T25 L Key Torx Wrench Removable I O cover Customer furnished parts If you will be controlling the TD61 via RS232 or RS485 you will need CAT 5 cables with straight through wiring and RJ45 connectors on each end oe ee 5 Wall Mounting Bracket Lower Retaining Bracket VGA Cable T 25 L Key Torx Wrench Remote Control Removable I O Cover Power Cable DB9 RJ45 Adapter 1 3 Using the Remote Control Most original setup operations are performed with the remote control Later RS232 control may be used The remote control shown below lets you control the TD61 and get it setup and adjusted initially For a complete description of remote control func tions See 6 1 Remote Control Functions on page 56 SOURCE PICTURE CURTAIN SIZE POS SAVE SETUP VOLUME Pie MONITOR MUTE VOLUME MENU PREV ENTER a E ety
23. 1 oe aa ect Dp p r v T 3 de Ss Ti INPUT 2 INPUT 3 LINE CUT EXTERNAL ET UST en Fr 03 Zu k Ta little f i ANALOG 1 D GITALIAHALOG 2 5232 RS4551M Rad s our A 1 i Lc 4 LA 4 p i d 1 ru i S x ge s z Lad i e i i hl LI 4 Left Side View TD61 Signal Input Panel EXTERNAL thru Control Inputs and Loop Audio Inputs and Outputs 21 2 5 Connecting RS232 RS485 Cables With serial control you can control one TD61 or several TD61s at the same time Connect to the computer Connect the TD61 to the serial out port of a com puter or another type of controller such as a video controller Connect with twisted pair computer serial cable such as Cat 5 using straight thru cable An RJ45 DB9 adapter is included in the accessory kit If you lose or need extras you can convert the 9 pin serial port to RJ45 with an adapter which you can buy in most electronic stores Wiring the adapter To go from 9 pin D sub serial connector on the back of the ccomputer to an RJ45 connector use a standard RJ45 to 9 pin adapter Wire it internally as shown The wiring shown for this adapter is correct for straight thru cables Straight thru cables are wired 1 to 1 2 to 2 etc Yellow wire 3 Black wire 2 Green wire 5 If you are connecting to more than one TD
24. 1adapter The TD61 will accept a wide range of computer resolutions up to UXGA 1600x1200 These connec tors are also used for RGB video with separate H amp V sync composite sync or sync on green and HDTV Video Connections The TD61 has three video inputs Composite video on a yellow RCA connector S Video on a 4 pin DIN connector and Component video on red Pr green Y and blue Pb RCA connectors All three are compatible with NTSC PAL and SECAM Audio Connections There are three stereo audio inputs using RCA connectors There is one stereo audio line out out put using RCA connectors and one pair of switchable 3 5mm monaural audio connectors for external speakers When external speakers are used the inter nal speakers are switched off Control Connections There is one RS232 input and one RS485 input for controlling the TD61 There is one RS485 loop through output that is used as the loop through for both RS232 and RS485 Power Connection AC power is connected to the TD61 at the bottom left side of the display An AC power cord is provided in the accessory kit 20 U 4 2 qu C gt ibid un ne nn 3 gt ag L Yi he am 8 d M As 8 A 72 e D un A 5 sh gt E a E ES ir INPUT 1 INPUT 2 INPUT 3 LINE OUT Video Inputs AAN OMPOSITE S VIDEO
25. 61 con nect from the computer or controller to the first TD61 It doesn t matter which unit this is Connect this first TD61 s RS485 Out to the next unit s RS485 In Start with RS232 and loop all the rest with RS485 22 The last display in a group should not usually need termination however if you are experiencing prob lems try terminating the last display by going to MAIN MENU ADVANCED OPTIONS gt SERIAL PORT SETTINGS and checking the TERMINATE RS485 box at the bottom of the menu 3 Adjusting 3 1 3 2 3 3 3 4 3 5 3 6 Aligning the Image 24 Adjusting TD61 To Its Source 28 3 2 1 Adjusting to Computer Sources 30 3 2 2 Adjusting to Video Sources 32 What Does Colorspace Mean 34 Color Balancing TD61 36 scaling and Cropping 38 Saving Your Work and Recalling a Memory 40 23 3 1 Aligning the Image Aligning the image will probably not be necessary However should there a be a slight misalignment it is important that you do this before you use the Position controls Adjust the image so that it covers the entire screen What is effective resolution The TD61 is the thinnest rear projection DLP product available This thin technology comes with some trade offs The ultra wide angle lens that allows it to be so thin causes the image to be distorted and undisplayable at the edges As a result the native 1280x720 engine resolution is not viewable on the screen The effective re
26. 9 FCC regulations 88 fill all 65 firmware revision number of 83 freq phase button 59 frequency max min 91 G global 70 Go Bright 76 go bright 76 Go Bright when fault 76 gray balance 75 Green in Color Balance 37 group ID 78 93 memory H position 82 current data in 67 heat from displays 91 number of 67 Hide menu 36 overwriting a 67 hours recalling a 66 lamp 74 saving to a 67 running time 74 slots 66 67 system time 74 menu auto setup options 79 color balance 75 ID definition of 78 Color Balance hide 36 Illuminate Border 24 diagnostics 71 Image Bowing 26 H position 82 input amplitude 90 lamp settings 77 input levels 28 menu options 82 computer sources 61 miscellaneous options 76 digital sources 62 picture 60 video sources 63 recall 66 interlock electrical 10 save 67 serial port settings 78 J serial port status 70 Justily 65 setup Summary 72 K test pattern 71 keys arrow 58 59 timeout 82 V position 82 L misc menu chain 57 lamp Miscellaneous Options 76 count 77 miscellaneous options menu 76 hours 74 mode ID 69 on off button 56 mode table analog saver 77 horizontal resolution 84 settings menu 77 mode ID 85 status 69 monitor menu chain 57 Lamp Hours 74 most recent fault 70 Lamp Saver 77 mullion last fault 69 glass mm 90 last packet address 70 width 90 last packet type 70 Mute 68 letterbox 65 mute 68 levels N adjus
27. CABLE TO THIS PRODUCT ALL OTHER WARRANTIES EXPRESS OR IMPLI ED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE ARE DISCLAI MED THERE NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF AND THE FOREGOING WARRANTY SHALL NOT BE EXTENDED ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY INFOCUS SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY MAY LAST SO SUCH LIMITATIONS MAY NOT APPLY TO YOU Limited Warranty Period The Limited Warranty periods hereof commence on the date of purchase by the end user customer These Limited Warranty provisions shall apply only to the end user purchaser first person or entity that purchased a new Product for personal or business use and not for the purpose of distribution or resale SOME JURISDICTIONS MAY GRANT YOU CONSUMER RIGHTS WITH MINIMUM WARRANTY DURATION THAT DIFFER FROM THE DURATIONS PROVIDED HEREIN AND INFOCUS WILL HONOR ALL SUCH CONSUMER RIGHTS To Be Eligible For Limited Warranty Coverage Any person exercising a claim under this Limited Warranty must establish to the satisfaction of nFocus both the date of purchase and that the Product was purchased new The sales receipt or invoice showing the date of purchase of the Product is the proof of the date of purchase To Obtain Warranty Service During the Limited Warranty period to exercise this Limited Warranty the purchaser must first
28. E 1 4 Your Safety is Important The TD61 produces UV ultra violet radiation internally and some parts are very hot For your con tinued health and safety we strongly suggest you read this section carefully The fully assembled display weighs about 106 lb When shipping these parts do not use styrofoam 48 08kg When unpacking and installing the TD61 peanuts These carry static electricity and can you will need two people to handle it damage the parts Use an anti static bag or if that is not available wrap the electronics module in aluminum foil AN WARNING The lamp gets very hot Allow it to cool for 15 minutes before removing it AN VVARNING Hot surface located behind the TD61 on the lower right side next to the exhaust vent Do not touch during operation A WARNING There is no electrical interlock on the screen Removing the screen does nofturn off the high voltage to the lamp SD WARNING Possible UV exposure Use protective eye wear while operating with viewing screen removed A CAUTION There are no user serviceable parts inside Refer all repair and maintenance to a qualified service technician AN WARNING There are protective electrical interlocks behind the left and right access panels Removing the access panels will cause the lamp to turn off Defeating these interlocks will risk exposure to UV Static electricity can damage sensitive electronic com ponents Always use a gr
29. M Program Information Serial Port Status RS 485 Press enter to clear Commands Received 24 Replies Sent 3 Diagnostics Last Packet Type Operation Last Packet Address This cube Bytes Received 231 Display Status 2 2 Bytes Sent 25 UART Framing Errors 0 RS485 Port Status b UART Overflow Errors 0 Group 0 Unit 0 19200 Baud Not Terminated Test Patterns gt Most Recent Setup Summary 2 dE HL me s ES Rs Lamp Ballast p ASES TS AE A A SS A SS E Hours P Commands Received is the number of commands that have passed through this TD61 whether or not they were addressed to it Replies Sent is the number of replies this display sent Last Packet Type will be most commonly an Event or an Operation You might also see Bad CRC or Bad Header if the packet were sent incorrectly Last Packet Address might be Global a command meant for all displays or a command meant for a group of which this display is a member such as a command addressed to 3 when this display s group ON SOURCE PICTURE ID 3 CURTAN SZEPOS Not This display a command meant for one or more other displays in this circuit but not this one such as d E Press MONITOR twice addressed to 45 or 4 or 6 when this display s ID is 37 to open the RS 232 This display Alone a command address exclusively to Jl Serial Port Status this display such as addressed to 37 and this display s ID jd menu Push three is 37 times to open the RS Bytes R
30. O SETUP OPTIONS menu and check DO BLACK WHITE LEVELS You can check the other items too particularly FREQUENCY and PHASE Now press TD61 looks for the darkest pixel and the brightest pixel in the picture and adjusts itself so that these are the truly the darkest and brightest When the BLACK WHITE LEVELS item is checked the TD61 will do this automatic level adjustment when ever a completely new source is displayed What is a completely new source TD61 remembers all the values in the last 10 pic tures If a new picture comes from a different source such as from a different computer and that picture has almost exactly the same resolution number of active lines number of blanking lines etc the TD61 will assume that this is a source it has seen before and use the remembered setup values This is a dif ferent sort of memory from the 40 numbered memo ries described in 3 6 Saving Your Work and Recalling a Memory on page 40 On the other hand if the new source is sufficiently different TD61 will engage all the checked processes in the AuTO SETUP OPTIONS menu When a saved memory is recalled from the RECALL menu TD61 does not do any auto setup Which is best Manual Semi Auto or Auto The manual and semi automatic methods are more accurate The automatic method works well for the BLACK LEVEL but it is sometimes not accurate enough for the WHITE LEVEL The good news is that you should only ha
31. Replacement lamps purchased after the time of Product purchase shall have a 90 day or 500 hours usage Limited Warranty Period from the date of replacement lamp purchase whichever comes first Accessory Product Limited Warranty Period one 1 year from date of purchase WARRANTY LI MI TATI ON AND EXCLUSI ON THIS WARRANTY SETS FORTH INFOCUS MAXI MUM LIABILITY FOR ITS PRODUCT THIS WARRANTY EXTENDS ONLY TO PRODUCTS PURCHASED FROM INFOCUS OR AN INFOCUS AUTHORIZED RESELLER nFocus shall have no further obligation under the foregoing Limited Warranty if the Product has been damaged due to abuse improper ventilation fire water disaster mispackaging shipping lightning or other acts of nature misuse neglect smoke exposure cigarette or otherwise accident unusual physical or electrical stress and or power surges unauthorized modifications including use of an unauthorized mount tampering alterations service other than by InFocus or its authorized agents or failure caused other than from ordinary use or failure to properly use the Product in the application for which said Product was intended In addition failure of the end user to follow maintenance procedures as outlined in the product s user guide where a schedule is specified for regular cleaning of certain parts based on usage and environment and the end user has failed to follow such schedule will not be covered under the Limited Warranty Finally InFocus shall have no further
32. Uniformity Uniformity Contrast Full Field ANSI Blackness Maximum Minimum _ Typical 85 Hz 56 Hz 91 1 kHz 31 47 kHz 165 MHz 132 VAC 190 VAC 110 VAC 254 VAC 200 VAC 230 VAC 63Hz 47 Hz 2 7A 1 35 A 1 23 4A 250 W 4 A 850 Notes 45 65 Hz auto ranging power factor corrected Notes 12 degree DMD Maximum Minimum _ Typical InFocus Stingray Thin Rear Projection Engine 0 8 HD2 1280 x 720 6 segment RGB spinning up to 5X display frame rate 1280 720 1232 693 115FL 135FL 90 40 55 1000 1 150 1 Pixels Pixels Pixels Pixels DNP Screen 150W WP 10 Internal White field test pattern DNP Screen 150W WP 10 Internal White field test pattern DNP Screen 150W WP 10 Internal White field test pattern ANSI 13 Internal uniformity test pat tern ANSI 13 Internal uniformity test pat tern Screen type SCN 5010 AG Internal Black White test pattern ANSI Contrast pattern 91 Optical Specification Maximum Luminance Non Uniformity Color Display Color Bit Depth Saturation EBU Color Point White Color Point Red Color Point Green Color Point Blue Color Matching of Primaries 0 030 Color Temperature Geometry Image Position 1 pixel Image Rotation 1 pixel Image Keystone 2 pixels Image Linearity 9 pixels Focus Focus Quality 3 Grade Scale Audio Audio inputs Line Out Speaker output Minimum 0 030 1 pixel 1 pixel 2 pixels 9 pixels
33. al pattern Color Balance C White Balance Red 6 Gv 4 76 100 Green EHE 84 100 Blue OJ G 92 100 OD Gray Balance All Red O E 68 7 7 Green 6 Ga 7 7 Blue 0m 3 amp 7 7 IM Test Pattern Off Hide Menu E Copy to Clipboard Recall From Clipboard Reset to Defaults Gamma Video White Boost Off 7 The white balance values will depend on the color temperature selected Those color temperature values will provide the starting point for the color balance procedure The gray balance values should all start at 7 8 Select HIDE MENU and press ENTER on each display This will remove all the menus so you can see the whole screen on each display To re open the Color Balance menu press ENTER for that display 9 Look at the displays together Stand far enough away from them so you are looking almost squarely at each of them Pay attention to the large central area not the edges 10 Determine which is the darkest display This is the baseline display Do not change this one 11 Go to the brighter display turn on the Color Bal ance menu by pressing ENTER Be close to the dis play to do this so only this display has the Color Balance menu showing 12 Match the brightness of brighter display to the darker display 13 Match brightness first Move the selector arrow to White Balance All e With the left key reduce the brightness until it matches the bas
34. ance Line Out Balance 50 50 67 Audio 68 Main Menu Picture Position Aspect Ratio Memory Diagnostics Advanced Options Program Information Volume use the keys on the remote to adjust volume Mute turns off the volume Treble use the keys on the remote control increase or decrease the treble response Bass use the keys on the remote control increase or decrease the bass response Speaker Enable disables both internal and exter nal speakers It does not affect line out Balance use the keys on the remote control to adjust the balance between both internal and external speakers Line Out Balance use the keys on the remote control to adjust the balance between inputs to an external amplifier Use Channel 1 2 3 for selected source allows you to select which audio input that will be used for the selected source Use the keys on the remote control to select the audio inputs 1 2 or 3 Mute Treble A 52 Bass Balance E 4 62 UE T y KA Speaker Enable 11 o Bae e Line Out Balance Use Channel 1 for 1 j i ANAQOU 7 Diagnostics Display Status Diagnostics Main Menu RS232 Port Status b Picture RS485 Port Status b Position gt Test Patterns Aspect Ratio __ Setup Summary Mama Lamp Ballast b Audio gt 4 Advanced Options b Program Information b The Display Status menu shows the status
35. bars 32 ambient operating temperature 92 amplitude video input 90 analog mode table horizontal resolution 84 mode ID 85 arrow buttons 58 59 audio 68 Audio Channel Select 68 auto lamp on 77 auto setup options menu 79 B Balance 68 Bass 68 Black Level 36 black level manual adjusting 30 blue only 63 Blue in Color Balance 37 Bowing 26 brightness specification for 91 buttons arrow 58 59 bytes received 70 bytes sent 70 C cables for RS232 straight thru 86 center point 30 certifications 88 clearance rear 90 Color Balance Hide menu 36 color balance menu 75 color balancing 28 36 color bars adjusting video with 32 colorspace 34 61 62 commands received 70 computer source adjusting to 28 30 computer sources adjusting to 30 connector diagrams 86 crop 65 current data in memory 67 current maximum 91 curtain 58 76 Curtain Pattern 76 D diagnostics menu 71 diagram connector wiring 86 diagrams of connectors 86 Digital 76 digital levels 62 dimensions 90 display status 69 DLP optical engine 28 do black level while level 79 do black white levels 30 do frequency 79 do phase 79 do position 79 dot clock 91 DVI 76 E EDID 28 76 EDID for DVI Analog 76 effective resolution 24 electrical specifications 90 Electronic alignment 27 enter button 59 environmental specifications 92 failed lamp indication 69 fan status 6
36. before The TD61 will recognize that it has seen this source before or at least a source with these characteristics and will recall the SVGA settings you established before This kind of recall includes Input Levels Position and Frequency Manually saving to memory slots The TD61 has 40 numbered memory slots and this is the best way to save Recall is fastest from memory slots First set up the TD61 the way you want it includ ing all the adjustments listed in this section Then press the SAVE button twice This opens the Save grid Navigate to an unchecked slot number or to a checked slot if you want to overwrite what s already saved Press ENTER This menu shows all the data that will be saved You can t change anything but the name in this menu save immediately press ENTER The appear ance of this menu is somewhat different for digital and video sources reflecting what is saved for them To change the name of the memory slot The default name is an abbreviated description of the contents In this case the name tells you that the source is connected to Analog 1 which is an XGA picture If you need a more descriptive name select the NAME line and press ENTER Use the left right arrow keys to navigate along the line Use the up down keys to change the character at that point Press PREV when finished Then select Save Now and press ENTER again 40 How to recall a memory slot 1 Press SAvE once to open the R
37. ce to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate receiving antenna ncrease separation between equipment and receiver Connect equipment to an outlet on a circuit different from that to which the receiver is connected e Consult your dealer or an experienced radio TV technician EN 55022 Warning This is a class A product In a domestic environment it may cause radio interference in which case the user may be required to take adequate measures The typical use is in a conference room meeting room or auditorium Note Any changes or modifications to the display not expressly approved by InFocus Corporation could void the user s authority to operate this equipment Use of a shielded interface cable is required to comply with the Class A limits of Part 15 of FCC rules Cther Certifications UL CUL CE FCC Class A 88 89 6 6 Specifications for TD61 Mechanical Specification Maximum Minimum Typical Notes Outside dimensions Width 54 9 139 45 cm Height 46 116 8 cm Depth 6 25 15 86 cm Pedestal height 14 75 37 47 cm Weight fully assembled 106 Ib 52 62 kg Shipping weight Orientation 10 Tilt or rotation Forward tilting may result in screen bowing and sub sequent image distortion Chassis color Bobcat Gray Ventilation requirement Rear clearance S
38. creen size Aspect ratio 16x9 Diagonal 61 154 94 cm Wiath 53 15 135 001 cm Height 29 922 76 002 cm Mullion 0 75 1 905 cm Electrical and Heat Specification Maximum Minimum Typical Notes Video input amplitude Component YPbPr Input 1 0 V p p 714 Vp p 05Vp p 75 ohm termination Conforming to standards 480i 480p 720p 1080i Composite analog 1 0 V p p 0 714 0 5 V p p 75 ohm termination Conforming to standards NTSC PAL SECAM TTL H and V sync 5 0 V 2 5 V 3 5 V TTL at 330 ohm termination Input connectors VGA 15 pin D sub female Analog 1 M1 Digital DVI standard shared with Analog 2 RCA female Composite video 4 pin DIN femal S Video RJ45 RS232 In amp RS485 In and Out RCA female Audio source 1 2 and 3 and Audio line out RCA female Component Video YPbPr 3 5mm stereo switchable external speaker connec tion 90 Electrical and Heat Specification Frequency vertical Frequency horizontal Dot clock AC requirements Line voltage 115 VAC range 230 VAC range Line frequency Line current Current draw 90VAC Current draw 100 120VAC Current draw 200 240VAC Current draw 254VAC Power Input AC fuse rating Heat BTUs per hour Optical Specification Optical Engine Imaging Device Native Resolution Color Wheel Resolution Resolution Horizontal Native Resolution Vertical Native Resolution Horizontal Viewable Resolution Vertical Native Brightness Peak Center Peak Bottom Center ANSI Uniformity
39. creen to moved out or in to compensate for the bowing The images at the right show the location of these screws 1 Loosen the three screws at the top of the screen 2 Grip the edge of the screen at the top and eIf the image is bowed down pull the top of the screen forward Ti the image is bowed up push the top of the screen back 3 Tighten the screws 26 Screen adjust ent screws Close up of screw showing elongated slot to allow adjustment Aligning the Image continued Electronic Alignment Once the initial alignment adjustments are com pleted you can touch up the edges by accessing the IMAGE ALIGNMENT menu Follow the menu path on the right to open the Image Alignment menu In the Image Alignment menu select TEST PATTERN Use the right and left arrows on the remote control to select GRID In the IMAGE ALIGNMENT menu select PAN IMAGE A Pan Image adjustment box I will open as shown below When Pan Image is selected remote control arrow keys will move the image up and down or left and right allowing you to center the image In the IMAGE ALIGNMENT menu select SHRINK GROW The SHRINK GROW adjustment box will open The remote con trol arrow keys will cause the image to grow or shrink The aspect ratio is locked so the image will shrink or grow in all directions uniformly Pan Image 19 1260 709 Effective Resolution 1241 x 698 Engine Resolution 1280 x 720 Shrink Grow 11 19 1260
40. de screen means force the aspect ratio to 1 77 the standard for many DVD movies Normal Video means force the aspect ratio to 1 33 the standard for television One to One means show the picture without any scaling If it is larger than the display s native res olution it will be cropped if it is smaller it will be shown with a black border This is most useful for 1280x720 resolution in order to show the image with no scaling artifacts and only a slight loss of pixels around the edges Justify determines how the picture will be placed on the screen f the picture is too wide for the display and is cropped on the sides you can choose LEFT CENTER Or RIGHT f the picture is too tall for the display and is cropped top and bottom you can choose MID DLE or BOTTOM Overscan Our rear projection technology is capable of showing every pixel of the incoming image Historically CRT televisions especially cheaper sets could not reliably show all the pixels without distortion Television industry standards allow a television set to chop off up to 2096 of the image This is known as overscan Some video content assumes that this overscanning is taking place and may not have picture information all the way out to the edges When shown on our dis play you may see black bars lines of white or other non picture information on the edges of an image Use the overscan setting to avoid seeing this Video inputs and YPbPr colo
41. down e 2 Temperature out of spec Temperature critical 4 7 Temperature ok Pulse Plateau Ratio Current to the lamp consists of alternating negative and positive plateau s each followed by a pulse Software Version Version of firmware embedded in the ballast Not to be confused with the firm ware version of the TD61 Status Can be queried via RS232 should the lamp be off Ballast Not Communicating If the ballast stops communicating with the electronics module the ballast menu will change as shown The electron ics module will lose all control of the ballast and the ballast voltage will go to maximum At maxi mum voltage the lamp life is significantly short ened 73 Diagnostics Hours Main Menu Picture 4 Position b Aspect Ratio b Memory b Audio b avanced Options FUCHS _ Program Information gt RS232 Port Status 1 RS485 Port Status Test Patterns Setup Summary b Lamp Ballast System Time is the number of hours and minutes the Tee electronics module has been running that is how long it has had power applied to it Sem M 02543 23 Running Time is the amount of time the optics have the lamp on that is how long light has gone cae heit PE through the optical parts of the TD61 E 22 Lamp is supposed to be the amount of time the lamp Reset LampHours has been on but it may be only the amount of time since this meter vvas last reset Running Time 01988 24 To r
42. e edges Overscan As with many rear projection televisions the InFocus TD61 uses overscan to ensure image quality For video images overscan is used to hide video artifacts such as the second audio channel or the sync information that is transmitted in the vertical interval Sometimes this vertical interval will appear as interference at the top of the screen Overscan allows you to adjust this out of the picture area For computer data overscan defaults to 096 Overscan E 1 Center 12 u 0 u u 8 a Crop o Letterbox Pillarbox T Widescreen 16x9 Normal Video 4x3 to One Memory Recall Memory Main Menu o Real 0 gt Picture p Save b Delete gt Memory 00 Diagnostics P Advanced Options gt Recall Program Information b In the Recall grid menu use the arrow keys to navigate through the memories that have something stored in them The empty memory slots are grayed out and you can t land on them Press ENTER to open the Recall detail menu The detail menu shows what will be recalled when you press ENTER again When Current appears in the Slot to Recall line it means that the TD61 is already doing exactly what this slot would tell it to do MET CURTAIN SIZE POS Press SAVE once to open the Recall grid VOLUME directly Fite VOLUME MONITOR MUTE PREV Ms 0170250133 M
43. ecall grid 2 Navigate to the slot you want to recall You can only land on slot numbers that have checks Press ENTER to open the Recall detail menu If this slot number has exactly the same settings are cur rently being used a Current message appears on the top line 3 The only line you can select is Recall Now Press ENTER The best practice is to recall settings from memory Slots It is faster Main Menu Memory Recall Memory i E amenn Recall 2 5 41 42 4 Operating 4 1 4 2 4 3 4 4 Normal Start Up 44 Reading the Alpha Numeric Display 46 Controlling TD61 with Remote 48 Controlling TD61 with RS232 RS485 50 43 4 1 Normal Start Up Start up sequence When AC power is turned on using the orange toggle switch on the electronics cage it seems that nothing happens for a few seconds The electronics module is starting up and initializing itself Next the alpha numeric display on the left front of the unit will display the message STARTING If the unit has not been turned on for a while and the optical engine is cool the message will say SEARCHING FOR SIGNAL and the lamp will start if AUTO LAMP ON has been checked in the lamp settings menu If not press ing the ON button on the remote control or sending an on command via RS232 will start the lamp If the lamp has recently been turned oft and the optical engine is still hot the message will read
44. eceived counts bytes received whether addressed to 485 Serial Port Sta this display or not tus Bytes Sent counts bytes this display sent out Most Recent shows the last several bytes decimal equivalent of the ascii hex value and the actual text of all commands received by this display whether addressed to it or not It does not show bytes or text sent 70 Diagnostics Main Menu Picture Position Aspect Ratio Memory Audio Advanced Options Program Information Test Patterns None White Red Green Blue Black Gray SOURCE PICTURE CURTAIN SIZE POS SAVE SETUP VOLUME ELLO MUTE VOLUME PREV ENTER deno Test Patterns La Gray Scale e Red Scale Green Scale B Blue Scale The Test Pattern menu turns on a variety of internally generated test ing picture Be sure to choose P 4 Diagnostics gt d Display Status 4 testing Diagnostics RS232 Port Status b RS485 Port Status y Test Patterns sD Setup Summary b Lamp Ballast b Hours g Grid 8 Alignment Dashes 4x4 Checkerboard Uniformity al Colors m Color Bars To set a custom test pattern color select Custom Color from the Test Pattern menu The Custom Test Pattern Color menu will appear on a neutral gray background Using the left and right arrows on your remote control to move the slider bars in the menu will cause
45. ed to our display you can try disabling Plug and Play and rebooting the computer to see if it acts any better Normally Plug and Play should be enabled EDID for Digital Analog 2 allows you to set up whether you have an Analog or a Digital source attached to the second connector This connector shares a single EDID line between the two sources so some graphics cards may not work cor rectly unless this is set to the appropriate choice Status Display Light adjusts the brightness of the status display readout Go bright when fault turns the status display readout to full brightness when a fault occurs Advanced Options Lamp Settings Main Menu Picture Position Aspect Ratio Memory Audio Diagnostics Program Information b Advanced Options YT YT YF Color Balance Miscellaneous Options Serial Fort Settings Auto Setup Options Image Alignment T T vi Y Menu Options Auto Lamp On when checked turns on the lamp shortly after AC power is restored When not checked the TD61 waits for a Lamp On com CUSPESINURS NS mand from the remote or from RS232 Rem ut RUM S Lamp Saver N CAUTION Lamp Saver Timeout 2hr The lamp must cool down for about Lamp Saver Timeout Omin one minute before lighting again A rapid on off on sequence may Lamp Settings reduce lamp life Also the lamp Before shutting down due to a missing should be allowed to heat up for at source TD61 will search each of the least f
46. eferred to as Product as appropriate purchased from InFocus an InFocus distributor or an InFocus reseller will conform to InFocus specifications and be free from defects in material or workmanship for the respective Limited Warranty period provided below InFocus does not warrant that the Product will meet the specific requirements of the end user customer If the Product while subject to this Limited Warranty is defective in material or workmanship during the warranty period then InFocus at its option will REPAIR or REPLACE the Product All exchanged parts and Products replaced under this Limited Warranty will become property of InFocus nFocus sole obligation is to supply or pay for all labor necessary to repair the Product found to be defective within the Limited Warranty period and to repair or replace defective parts with new parts or at the option of InFocus serviceable used parts that are equivalent or superior to new parts performance Limited Warranty periods are as follows e Product Limited Warranty Period Excluding Lamps 1 year from date of purchase Lamp Product Limited Warranty Periods From the date of Product purchase the original installed lamp shall have a 90 day or 500 hours usage Limited Warranty Period whichever comes first Replacement Lamps purchased at the time of Product purchase will have a 90 day or 500 hours usage Limited Warranty Period from the date of installation whichever comes first
47. eline display Select the individual colors and adjust the amounts of Red Green and Blue to achieve the best match in color and brightness to the baseline display 14 When each display matches in white change TEST PATTERN to Gray so the displays show an internal gray pattern The gray values range from 0 to 15 and they are all now set at 7 Therefore gray can be adjusted up and down Choose which dis play has a middle brightness and that has very little color in gray This is the display you will match to It does not have to be the same as the display chosen for white bal ance 15 When the displays match in gray turn off the test pattern on each display with the top item in the COLOR BALANCE menu COPY TO CLIPBOARD will save all the current settings to a temporary memory You can then make more adjustments to see if it gets better or worse RECALL FROM CLIPBOARD will restore these saved settings The clipboard is only for testing These values are not saved when AC power is off While color balancing change the White value by a lot not just one step It s difficult to see one step in White A large change will tell you if you are heading in the right direction If you can t decide which way to go or how to get this display closer to the others try any change If it is the wrong change it will be quickly obvious and you can go back Use the clipboard Color balance values are saved for all input sources in
48. em MONITOR MUTE VOLUME PREV 81 Advanced Options Menu Options Main Menu Picture Position A t Rati speci Ratio Advanced Options Memory Audio Color Balance i Diagnostics Miscellaneous Options d Lamp Settings b Program Information P Serial Port Settings Auto Setup Options FT T YT YT YT YF Image Alignment H and V Position move the location of the menus on the screen Menu Options the menu on indefinitely 82 Program Information Main Menu Program Information The middle section shows the native resolution of the TD61 and the Revision number of the firmware 83 6 3 1D61 Drawings Dimensions in inches 54 870 31 654 46 049 T FRONT SERVICE A REMOVABLE PANELS 3 PLACES nn AA A REMOVABLE FEET L FRONT INTERNAL SPEAKERS 5 PLACES 2 PLACES TD61 Front View 84 cS Pr 2 755 ELECTRONICS I O REMOVABLE COVER NOT SHOWN Left Side View 10 065 DETAIL A SCALE 1 2 Signal Input Panel WALL OR PEDESTAL 7 MOUNTING BRACKETS lt NOT SHOWN V REAR INTERNAL SPEAKERS 2 PLACES Rear View REMOTE CONTROL IR POWER ON LED STATUS INDICATOR DETAIL B SCALE 1 4 AND DIAGNOSIS DISPLAY LCD Display 85 6 4 Connector Wiring These are connector diagrams with pin designations All connectors on these pages are shown looking at them from the outside not from
49. em all one at a time to that one For more information on Color Balance see 3 4 Color Balancing TD61 on page 36 Color Balance Color Temperature 5500K Medium Warm Red GE r 28 26 6 a 9 8 24 24 Blue 20 29 21 23 3 Gray Balance All Red 5 qa__ 8 41 441 8 2 9 7 9 Blue q__ 10 12 IM Test Pattern White A Hide Menu Copy to Clipboard Recall From Clipboard Reset to Defaults Gamma Film White Boost Off 75 Advanced Options Miscellaneous Options 76 Main Menu Picture Position Aspect Ratio Memory Audio Diagnostics Program Information Advanced Options Color Balance b Lamp Settings Serial Port Settings Auto Setup Options Image Aliqnment T T YT YT Y Menu Options Miscellaneous Choose pattem for lt CURTAIN gt key Plug and Play EDID Enable EDID for DVI Analog 2 Status Display Light CX 128 Go bright when fault Curtain Pattern is a choice of any of the solid color test patterns or the logo This is displayed when you press CURTAIN Plug and Play enables the Extended Display Identification Data EDID that is used by many computers to determine the capabilities of the monitor This is a compli cated standard and not all video card drivers and operating systems act the same If you are having trouble getting your video card to output a picture when attach
50. eset lamp hours select one of the Confirm Lamp Hours Reset resets press ENTER press the left arrow press ENTER again Are you Sure Yes N Confirm Lamp Hours Reset Are you Sure Yes Advanced Options Color Balance Main Menu Picture Position Aspect Ratio Memory Audio Diagnostics Program Information T T YT YT YT Y 4 Advanced Options Miscellaneous Options Lamp Settings serial Port Settings Auto Setup Options Image Alignment Menu Options cw 099 Match the whites Use color balance to match all the displays in a group Reset values on all displays to numbers shown in top illustration with white test pattern Match all displays to least bright display Change the Blue value as little as possible When adjusting WHITE BALANCE ALL you may not see all three of the red green and blue numbers decrement or increment This because the ALL choice adjusts the colors in proportion to each other so that the color remains constant as you adjust the brightness For example if you have the color set at Red 100 Green 80 and Blue 40 and adjust down 10 clicks you will wind up with Red 90 green 72 and Blue 36 The color has remained the same and only the brightness has changed Green and blue did not change on every one of the ten clicks Match the grays Adjust the grays using the gray test pattern again matching all displays to each other Choose one display that has a neutral gray and match th
51. ging If it doesn t need changing after six months inspect again in a year As long as the environment doesn t change you can build an appropriate schedule in this way If new construction occurs in the vicinity of the InFocus displays watch out New construction usu ally means DUST Changing the Filter 1 Turn off the lamp and wait 15 minutes till the lamp cools down The display status readout on the front of the TD61 will tell you when the cool down period is over usually about 45 seconds Turn off the AC and unplug the AC cord 4 This is the TD61 filter in its holder Remove the foam filter from the filter holder 5 Install new filter in the filter holder and insert the new filter in the filter housing 54 6 Reference Section 6 1 6 2 6 3 6 4 6 5 6 6 Remote Control Functions 56 Menus Structures 60 TD61 Drawings 84 Connector Wiring 86 Regulatory Information 88 Specifications for TD61 90 55 6 1 Remote Control Functions The next four pages explain the actions of the remote control Picture Source Anattog tt Colorspace RGB Sync Type Separate H amp V Vertical Frequency 60 Hz Horizontal Frequency 43 38 kHz Pixel Frequency 65 02 MHz FA Horizontal Resolution 1024 i Vertical Resolution 768 Frequency 1344 Phase CHEO 9 22 5 A Sharpness Sharpest Input Levels LS Turns the lamp on and off On SOURCE PICTURE Picture Position 50 arrow koys lo move
52. i 018025034 17 015023031039 Cle 0 02 132 1 40 l Recall Slot to Recall 1 Name AN1 1024x768 2x2 1 2 Source Analog RGB 1 Colorspace RGB Resolution 1024 x 768 Scale Justify Widescreen Center Position 328 4 Frequency Phase 1344 0 Sharpness Normal Black Level 52 50 104 White Level 178 131 135 Volume Treble Bass 46 48 53 Mute Speaker Input E Channel 1 Balance Line Out Balance 50 50 66 Memory Save Memory Main Menu Recall Picture b Save Position p Aspect Ratio b Audio Diagnostics Advanced Options T YT YF Program Information In the Save grid use the arrow keys to cycle through the available memories As you navigate through all 40 memories Save Now will show Overwrite as shown here For each empty memory the Name of the memory is the default name for this slot You can change this name as described below Many lines are grayed out because you can t change anything here except the name of the memory The lines in this menu are different for saving different modes video or digital Overwrite appears if the Save to Slot number currently has something saved in it To save highlight Save Now and press ENTER A Current notice will appear in Save to Slot to indicate that the save was successful and that the slot now con tains exactly what the TD61 is doing now Everything shown in the Save menu is saved in
53. iage return LF line feed Baud Rate is 2400 4800 9600 or 19200 Terminate RS 485 adds electrical termination to the RS485 Should not normally be needed Advanced Options Auto Setup Options Main Menu Picture Position Aspect Ratio Memory Audio Diagnostics Program Information T T YT YTF YT YF Advanced Options Color Balance Miscellaneous Options Lamp Settings Serial Port Settings Image Alignment Menu Options The checked events occur when e the input changes say from XGA to UXGA anew source is selected you press the SETUP button Retry on lost signal when checked means the TD61 will try again to detect the mode if the sync is lost or momentarily disrupted If you have a noisy signal you want to turn this off to avoid dis ruption in the image However if this is unchecked the system will not correctly set up the signal if you change resolutions Do Black White Levels automatically adjusts the lightest and darkest pixels to be white and black This fully automatic method is prone to small errors in the white level Semi automatic level adjustment is better v Auto Setup Options INE E IU Retry on 5st signal Do Black White Levels NA Do Frequency vf Do Phase NA Do Position Do Frequency and Do Phase automati cally adjust the electronics module to the frequency and phase of the selected picture Do Position puts the upper left pixel of the picture in
54. ice Many resources are available on our website Some examples are e Frequently Asked Questions about general projector usage and technical issues e E mail Support e Online product registration e Product data sheets e Optional accessories e Technical specifications InFocus USER S GUIDE InFocus Corporation 27700B SW Parkway Avenue Wilsonville Oregon 97070 9215 1 800 294 6400 503 685 8888 Fax 503 685 8887 http www infocus com In Europe InFocus International BV Strawinskylaan 585 1077 XX Amsterdam Corporate Sales Review The Netherlands Phone 31 20 579 2000 Fax 31 20 579 2999 In Asia 238A Thomson Road 18 01 04 Novena Square Singapore 307684 Telephone 65 6334 9005 Fax 65 6333 4525 071 0002 00 010 0567 00
55. if they are not grayed out lighted function will do or what it is used for Vertical Resolution 768 i Sharpness harpest Clicking in the Source item opens a drop down menu that allows you to choose a source Inout Levels Analog Sources Main Menu Position Aspect Ratio Memory Audio Diagnostics Advanced Options YT YF Program Information For Digital Sources see page 62 For Video Sources see page 63 When the source is Analog 1 or 2 and has RGB color space See 3 3 What Does Colorspace Mean on page 34 To set levels semi automatically display a black picture from the source computer Choose Auto Black Level and press ENTER Then display a white picture from the source choose Auto White Level and press ENTER The TD61 is now adjusted to the brightest and darkest picture this one source can produce If you change the computer to a different one or change the video card in the computer you should do this adjust ment again Picture C3 Source Analog 1 Colorspace RGB Sync Type Separate H amp V Vertical Frequency 60 Hz Horizontal Frequency 43 38 kHz Pixel Frequency 65 02 MHz Horizontal Resolution 1024 1 Vertical Resolution 768 CJ Frequency 1344 Phase 225 Sharpness Sharpest Input Levels Auto White Level gain Center Point 2 1 4 x Black Level offset All 9 55 Red C 68 67 Blue 69
56. ings Serial Port Settings Auto Setup Options Menu Options Image Alignment Pan Image Shrink Grow Reset to Default O iluminate Border Remove screws To access the adjustments on the small mirror remove two screws under the center access panel and remove the panel yx u Small mirror showing three image adjustment screws If initial inspection shows that the image is square skip this section and go to Electronic align ment on page 27 Squaring the image is be done by adjusting the small mirror behind the center access panel Use the supplied Torx wrench to make the adjust ments Loosening all three screws exactly the same amount will make the image bigger Adjusting them in will make it smaller Adjusting screws 2 and 3 the same amount will adjust the width of the top of the screen Adjusting screw 1 will adjust the width of the bot tom of the screen Loosen screw 1 to widen the bottom of the image Loosen screws 2 and 3 to widen the top of the image Adjust screw 3 to square up the top Adjust screw 2 out to square up the top left Aligning the Image continued Bowing Because the screen is so large there is a certain degree of flexibility in the screen that can cause bowing at the top of the image There are three screws in the top of the screen that are adjustable When loosened they allow the s
57. ions for TD61 90 46 50 1 Introduction 1 1 About the TD61 4 1 2 Accessories for TD61 6 1 3 Using the Remote Control 8 1 4 Your Safety is Important 10 1 1 About the TD61 The InFocus TD61 is a 61 rear projection display in a native 16x9 format designed to outperform large format plasma displays It combines ultra thin 6 5 deep rear projection DLP technology and rugged reliable design for outstanding performance in digital signage applications Scale TD61 will up sample resolutions up to a resolu tion of 1280 x 720 720p and will downsample reso lutions up to 1600 x 1200 Video inputs A standard 15 pin VGA connector accepts com puter pictures up to 1600 X 1200 It also accepts video RGB with separate H amp V Sync composite sync and sync on green An M1 connector accepts computer images as well as Digital Video An S Video input is available using a standard 4 pin Din connector A component video input is available as Y Pb Pr on three RCA connectors color coded green blue and red A composite video input is available on a yellow RCA connector Audio There are three stereo audio inputs using RCA connectors There is an output connection for exter nal stereo speakers as well as a line out to be used as an input to an external stereo amplifier Communication Communicating with the TD61 will be done via an RJ45 RS232 input or an RJ45 RS485 input Loop through from either source will be
58. isplayed In these instances the alpha numeric display will provide the information shown below e TEST e LOGO e CURTAIN 47 4 3 Controlling TD61 with Remote You can control TD61 with the remote control or with RS232 commands Remote control The remote control projects a series of IR infra red pulses to the TD61 for control Aim the remote control at the bottom left of the screen and press MENU The main menu should be visible if the lamp is on When the TD61 receives a signal from the remote control and the signal is accepted a solid block will appear as the last character of the LCD dis play If the signal is not accepted or understood an X will appear SOURCE PICTURE CURTAIN SIZE POS SAVE SETUP VOLUME EI MONITOR MUTE VOLUME ee MENU PREV MEM For a complete list of all remote actions see 6 1 Remote Control Functions on page 56 If the remote doesn t work The batteries in the remote are dead or installed wrong The remote was not aimed at the screen Something is blocking the IR receiver in the TD61 A The remote control has a large spread of its IR radiation If you find you are having a difficult time controlling the T D61 move closer and aim the remote at the lower left corner of the display 48 49 4 4 Controlling TD61 with RS232 R5485 Connect the RS232 In to the computer Loop thru with RS485 Remote control with serial commands is a good way to cont
59. ive minutes before turning other connectors for an active source If them off another source is not found Lamp Saver if checked will turn off the lamp after a specified length of time When shut down starts TD61 displays the message below Lamp Saveris On Shutting Down 77 Advanced Options Serial Port Settings 78 Main Menu Picture Position Aspect Ratio Memory Audio Diagnostics Advanced Options T T YT YT YT F Color Balance b Mi LI Opti Program Information gt Iscellaneous Options Lamp Settings Auto Setup Options Image Alignment Menu Options 2 Group ID can be 0 9 A Z caps only Unit ID can be 0 9 A Z caps only In combination this gives 1296 unique IDs serial Port Settings The ID is the identification of the individual Group display The address is the part of an RS232 Unit that specifies which display or displays should ASCII Response Type Symbolic execute the command Put another way the ID ASCII Response Terminator CR LF is the number on your house the address is Baud Rate 19200 the number on the envelope that tells the letter 7 Terminate RS 485 carrier where to take it ASCII Response Type determines whether the response comes back as text Symbolic or an command numbers with the display ID Numeric or with the numeric data only Data ASCII Response Terminator determines what non printing character s are sent at the end of each message CR carr
60. nc Hot Plug Detect IK PU TMDS Data TMDS DataO TMDS Data05 shield NC NC TMDS CLK shield TMDS CLK TMDS CLK Analog Red Analog Green Analog Blue Analog HSync Analog Gnd 87 6 5 Regulatory Information Declaration of Conformity Manufacturer s Name InFocus Corporation Manufacturer s Address 27700B SW Parkway Avenue Wilsonville Oregon 97070 9215 declares that the product Model Number TD61 Product Options All conforms to the following EU Directives and the standards stated Safety UL60950 Safety of Information Technology Equipment Electromagnetic Compatibility Directive 89 336 EEC and amendments EN 55022 CISPR 22 Radiated and Conducted Emissions from Information Technology Equipment EN 55024 CISPR24 Information Technology Equipment EN610000 3 2 Harmonic Emissions EN610000 3 3 Voltage Fluctuations and Flicker Emissions FCC Regulations This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in an installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interferen
61. nd tighten the cap tive screw 7 Replace the access panel Resetting the lamp hours It is a good idea to reset the lamp hours to zero when you install a new lamp If you are replacing a lamp under warranty you will be asked how many hours were on the lamp when it failed The following menu train will lead you to Reset Lamp Hours Main Menu Diagnostics Hours 53 5 2 Changing the Air Filter Clean cool air is essential to proper operation of the TD61 When should I change the air filter 2 Remove the left access panel by removing the two When it gets dirty change it 6x32 screws at the bottom of the panel and slid Unfortunately there is no absolute rule about ing the panel to the left when to change an air filter For some installations the environment has clean dust free air such as a corporate lobby The air filter may be good for a year or more In other environments airports subway termi nals the air is full of dust and dirt all the time The air filter might have to be changed every month Of course it also depends on how many hours per day or per week the lamp is on and the fans are run ning Filter How to determine a changing schedule Remove and inspect the air filter after three months of operation Make a note of the air filter s condition Then check it again after six months of operation These two inspections will give you some idea of how often the filter needs chan
62. nformation about the TD61 It provides infor mation on failure modes active source source status format if video TD61 Alpha Numeric Display The first line of the Alpha Numeric Display con tains the following information Failure modes modes that cause the lamp not to light are prefixed with 46 Door Open either of the interlocks on the front access panels is open Fan Stopped high voltage power supply fan has stopped Engine Fan Stopped either the DMD fan or the lamp fan has failed HV Power Supply ballast voltage to the lamp has failed Opt Engine Com optical engine is no longer communicating with the electronics module Lamp Failed lamp not striking Cooling Down xx xx is a countdown of the num ber of seconds starting at 45 until it is ok to light the lamp Lamp Saver Active see page 77 Ready it is ok to light the lamp Turning on lamp Running OK The second line in the display contains the active source and its status Analog 1 Analog 2 Digital component S Video Composite Status is one of Adjusting No Signal xxxx yyyy horizontal and vertical resolution If the source is video instead of resolution it will have the video format NTSC NTSC 60 443 PAL 50 358 PAL YPbPr 60Hz YPbPr 50Hz SECAM If a curtain or test pattern is being displayed it is sometimes difficult to understand why the source input is not being d
63. obligation if the Product was subjected to operating conditions outside of the range specified in the user s guide or in this warranty Normal operating conditions are defined as use not in excess of 16 hours continuously per day with a minimum 8 hour period of continuous rest in the powered off state If a claimed defect cannot be identified or reproduced in service you will be held responsible for the costs incurred This Limited Warranty excludes Product cleaning removal or installation of the product repair or replacement of plastics or glass due to cosmetic damage and damage as a result of normal wear Product repair outside of the terms of the Limited Warranty will be on a time and materials basis InFocus will not be liable for any rental costs incurred in the event of a failure The warranty does not apply to cartons carrying cases shipping cases external cabinets accessories used in connection with the product or cosmetic parts knobs or batteries The Accessory Product Limited Warranty covers the accessory item only and excludes normal wear The Lamp Product Limited Warranty excludes expected lamp degradation Remanufactured Products and Software Products are exempt from the foregoing Limited Warranty Please refer to the appropriate Remanufactured Product Limited Warranty or Software Product Limited Warranty for applicable Warranty information DI SCLAI MER OF UNSTATED WARRANTIES THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLI
64. of the lamp and fan 573 is the firmware number For TD61 it will be 573 2201 Display status Fan On when running When a fan fails the lamp will TD64 not turn on and you can t see this 573 2200 Rev 1 0 Lamp when the lamp fails you can t see this Optical Engine SN 41034400100342 menu ID Tag PS Fan On Eng Fans On Lamp On Interlock ok Temperature 38 C SOURCE PICTURE Fault Override is On pia Mode ID T HPer 1742 VLines 806 SAVE Last Fault Interlock 0175 05 VOLUME Mode ID Each mode has a number and this is the VOLUME number of the one used now For XGA for instance there are several each with a different vertical fre quency number of active lines total number of lines Press MONITOR once to open the Last Fault Shows the last event that caused the lamp to display Status menu go off and the elapsed system time not clock time in hours minutes since that happened Time is in 5 minute increments and does not update while the menu is open 69 Diagnostics Serial Status Serial Port Status RS 232 Press lt enter gt to clear Main Menu Commands Received 24 Replies Sent 3 Last Packet Type Operation Picture 4 Last Packet Address This cube Position P Bytes Received 231 z Bytes Sent 25 Aspect Ratio UART Framing Errors 0 p UART Overflow Errors Group Unit 19200 Baud Audio p Most Recent PA Options RE
65. ounding strap when handling the electronics module or the optical engine if there are exposed components Can shock burn or cause death Disconnect power cord before High intensity light Do not look into the projection lens when the viewing screen Hazardous voltage inside is removed Possible UV Exposure Use protective eye wear while operating with viewing screen servicing this unit removed 334 0077 00 Refer to service manual for details No user serviceable parts inside Refer all service to qualified serviceman h a34 0100 00 Hot Surface N AX A WARNING AVERTISSMENT WARNUNG TURN OFF E SWITCH PEE OPENING COVER M C HANDLE BULB WITH CARE SEE USER S MANUAL FOR LAMP REPLACEMENT COUPER L ALIMENTATION ELECTRIQUE AVANT OUVERTURE DE LA FACE AVANT ATTENTION LA LAMPE EST CHAUDE LAISSER REFROIDIR AU MOINS 15 MINUTES AVANT SON REMPLACEMENT RISQUE D EXPLOSION MANIPULER L AMPOULE AVEC PRECAUTION SE REFERER AU MANUEL DE L UTILISATEUR POUR TOUT REMPLACEMENT DE LA LAMPE DEM OFFNEN DES DENKELS STROM ABSCHALTEN VORSICHT EXPLOSIONS GEFAHR LAMPE IST HEIR WARTE WENIGSTENS 15 MIN F R DIE LAMPE ZUM ABK HLEN VORSICHT MIT DER LAMPE BEIM HANTIEREN FOLGE ANWEISUNGEN F R DEN LAMPEN WECHSEL IM REPARATUR MANUAL 334 0078 00 2 Installation 2 1 2 2 2 3 2 4 2 5 What You Will 14 Unpacking the TD61 16 Installing the TD61 18 Connecting Source Cables
66. puter for the program Nor can you use the TD61 black test pattern Hint Make a black screen from Windows Paint program 2 In the INPUT LEVELS menu select AUTO BLACK LEVEL and press ENTER 3 Display a white picture from the source 4 Select AUTO WHITE LEVEL and press ENTER That s all there is to it The TD61 is now adjusted to the black and white levels of this computer using this video card If you change computers or video output cards in the computer you must do this again Adjusting levels manually 1 Display an all black picture from the source com puter 2 Press PICTURE on the remote to open the PICTURE menu 3 Select LEVEL at the bottom of the menu 4 Select BLACK LEVEL and adjust it up and down with the keys to make the three CENTER POINT values go to zero If they do not all touch zero at the same time use the individual colors under BLACK LEVEL to adjust them Do not go beyond the point where the Minimum just goes to zero The idea is to just touch the zero level 5 Display an all white picture from the source com puter 6 Select WHITE LEVEL and adjust the levels until the CENTER POINT values just touch 255 adjusting the individual colors as necessary amp Itis not a good idea to use the levels to make the displays match each other That should be done with the COLOR BALANCE menu 3 4 Color Balancing TD61 on page 36 30 Adjusting levels completely automatically Open the AUT
67. rol a TD61 while it is operating It s also an easy way to control TD61s during initial setup using a control program Display IDs When the displays are connected in a series loop each display should have a unique ID The ID is set in the Serial Settings menu The GROUP ID and the UNIT ID go together to make the display s ID Each of the two parts has a range for characters from to 9 and from A to Z not case sen sitive Addressing the displays When you send a command it will have an address There are tive forms of the address To address all the displays in this serial loop use for the address address a single display use the specific ID of that display such as A6 or 00 or 1B To address all the displays with a certain Group ID use an address like 3 which will address all the displays in group 3 To address all the displays with a certain Unit ID use an address like 0 or 3 When you don t know the ID of any display you can address the first one in the serial loop with ID This will cause only the first display in the series to perform the command 50 Main Menu Picture 1 Position Aspect Ratio 4 Audio Diagnostics gt Program Information N Advanced Options Color Balance gt Miscellaneous Options pj Lamp Settings Auto Setup Options b Image Alignment gt Menu Options gt Serial Port Settings Unit 0
68. rpness Sharpest Input Levels gt VOLUME RE s MONITOR MUTE VOLUME Selects the highlighted item If there is an arrow in the item this button goes to that menu Selects the previous menu Moves through the items in a menu In some menus Position Position these button control up down movement 59 6 2 Menus Structures Picture 60 Picture Colorspace 1 Analog 2 SyncType Separate O Digita Vertical Frequency 1 Component YPbPr Horizontal Frequency 4328 kHz sh Composite EA Horizontal Resolution 1024 0 T Vertical Resolution 768 00 Frequency 184 El Phase 25 put Levels Picture Main Menu Video Standard NTSC 60Hz 3 58 MHz 4 Sharpness Sharpest Position P ij aa Aspect Ratio b Memory Picture 4 22 Diagnostics P 5 M u jita Advanced Options b Colorspace RGB Program Information gt Vertical Frequency 60 Hz Horizontal Frequency 43 38 kHz The Picture menu has different items HonsentalResolutien 1024 depending on the current source type You cannot adjust Frequency in Digital pic tures so that item is not in the Picture menu when the selected source is Digital Input Levels You cannot adjust Horizontal Frequency in Analog because that is determined by the source so it is grayed out Other items can In most menus this area describes what the selected high be adjusted
69. rspace inputs have a default overscan of 396 which will match most modern TV sets Computer inputs default to 0 overscan so you see the whole image amp It may be desirable to display 1280x720 images without any scaling Since the effective resolution of the TD61 is less than 1280x720 scaling will occur and cause some artifacts To avoid this choose ONE TO ONE for a scale mode No scaling will occur and a few pixels on the edge of the picture will be cropped off ONE TO ONE can be used for any input mode It will be cropped if it is larger than the effective resolution or displayed in the center of a black field if it is smaller 39 3 6 Saving Your Work and Recalling a Memory Some saving is done automatically but there are big advantages to saving your work manually There is more information about memories starting on page 67 How automatic save works Whatever changes you make with the remote con trol or RS232 commands these changes are saved automatically If you change sources switch to another input connector and come back to this source everything you did before will be recalled Things will look like they did before Suppose you make adjustments to an SVGA source on Analog 1 then you feed a UXGA source to Analog 1 and make new adjustments Then you switch to the S Video 1 connector and do some more setup for it Later you switch to the Analog 1 input again and this time it has the SVGA source from
70. s HGB In RGB there are separate conductors wires for red green and blue Full white is represented by a 100 6 signal level on all three conductors Black is represented by a 0 level on all three Dark red is represented by say a 30 level on the red conductor and 0 on the blue and green RGB signals need sync for horizontal and vertical This may be separate sync on two additional conductors composite sync H amp V sync mixed together on a separate conductor RGBS sync on the green channel RGB In this manual RGB refers to all of these types unless one of them is specifically called out YPbPr YPbPr also has three conductors The Y conductor carries the luminance bright ness signal level as well as composite sync This luminance brightness signal is developed by combining red green and blue in certain propor tions 3096 red 5996 green and 1196 blue The Pb line carries a signal that represents the blue component of the picture minus the lumi nance component B Y The Pr line carries a signal that represents the red component of the picture minus the luminance component R Y YPbPr is sometimes called YUV and sometimes called component video DVD players often have a set of three component video connectors This makes a picture of substantially higher quality than the single conductor Video Out Video In connection Use the correct colorspace f the picture i
71. s coming from S Video Composite or the Component outputs of a DVD player the TD6lautomatically sets the colorspace For Analog and Digital inputs colorspace must be set by the user 34 amp Note For DVD players outputting component video you should use the component input RCA connectors For interlaced signals this will give a better picture than through the analog input If the signal is non interlaced or HDTV you must use the analog connector How does the YPbPr system make green At first glance it may look like the YPbPr system doesn t have any way to render something green But look beyond first glance The Y part of the signal has a green component in it Y is made from 59 of the green of RGB 30 of the red and 11 of the blue By combining the Y the B Y and the R Y signals algebraically it is possible to convert the YPbPr signal into RGB This conversion is performed in the elec tronics module of the TD61 When the Colorspace item in the Picture menu is set for RGB the electronics module sends the three colors through to the optical engine without transla tion It is only processed by the Input Level settings and the Color Balance settings When the Colorspace is set to YPbPr the input signal is first translated to RGB before it is processed by the Input Level and Color Balance settings and sent to the optical engine Picture ti Colorspace RGB Sync Type Separate H amp V Vertical Frequency 60
72. solution of the display i e the number of pixels visible on the screen is about 1232x693 pixels but may vary slightly from unit to unit Because the position of internal mirrors and lenses may shift very slightly during shipment of your TD61 the effective resolution window may also shift The Image Alignment menu allows adjustment of the effective resolution in order to compensate for any minor variations that may occur after factory alignment Aligning the Image 1 Turn on the AC power to the display On first turn on the lamp will power up automatically You may choose later to turn off the auto lamp on in the menu See Advanced Options Lamp Settings on page 77 Press MENU on the remote control Select ADVANCED OPTIONS and press ENTER Select IMAGE ALIGNMENT Select rEST PATTERN and use the keys to select GRID and check ILLUMINATE BORDER A N Use the test pattern to align the image to the screen The Grip pattern is good for general alignment ILLUMINATE BORDER will allow you to see just how far from the edge of the screen the active image will be by turning the background green The green background will appear outside the edges of the test pattern It will turn to black once you exit the menu 24 Main Menu Picture Position Aspect Ratio Memory Audio Diagnostics wow row Y ow Program Information d Advanced Options J Color Balance Miscellaneous Options Lamp Sett
73. the first TD61 Adjusting with color bars 1 If possible use a color bar pattern from the video source you will use for the program material You cannot use the color bar from the Test Patterns menu 2 In the Picture menu check Blue Only You should see only the alternate color bars all of them blue 3 Adjust Saturation to make the outer two color bars match Match them in brightness they will already match in color 4 Adjust Hue to make the inner two color bars match 5 Uncheck Blue Only When a video source is selected Auto Setup Options is not available Adjustments must be made manually 32 6 If the color bar pattern has a pluge you can use it to adjust Brightness Pluge A Adjust Brightness so you can not see the difference between these two marks but you can see the difference between these two marks Saturation Match these Match these Adjust Saturation so the outside bars match when Blue Only is checked Hue Match these Match these Adjust Hue so the inside bars match when Blue Only is checked 33 3 3 What Does Colorspace Mean 3 3 What Does Colorspace Mean There are many ways to represent a color picture electronically and YPbPrare the two most com mon in analog and digital sources The display will accept either What does colorspace mean There are two types RGB and YPbPr and they carry the picture information on three conductors or wire
74. the remaining period of the Product Limited Warranty whichever is greater LIMITATION OF LIABILITY IT 15 UNDERSTOOD AND AGREED THAT INFOCUS LIABILITY WHETHER IN CONTRACT IN TORT UNDER ANY WARRANTY IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL INFOCUS BE LIABLE FOR SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOST PROFITS LOST REVENUES OR LOST SAVINGS THE PRICE STATED FOR THE PRODUCTS ISA CONSIDERATION IN LIMITING INFOCUS LIABILITY Limitation on Bringing Action No action regardless of form arising out of the agreement to purchase the Product may be brought by purchaser more than one year after the cause of action has accrued Governing Law Any action regardless of form arising out of the agreement to purchase the Product is governed by Oregon law Mandatory Arbitration Any action regardless of form arising out of the agreement to purchase the Product is subject to mandatory arbitration SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS DEPENDING ON JURISDICTION IF YOU NEED ASSISTANCE For all types of Service and Support information on InFocus products and services please go to our web site at www infocus com serv
75. the upper left corner of the screen 79 Advanced Options Image Alignment 80 Main Menu Picture Position Aspect Ratio Memory Audio Diagnostics Program Information Advanced Options Color Balance FF T F serial Port Settings Auto Setup Options Menu Options Pan Image moves the entire image vertically or hor izontally Shrink Grow allows you to shrink or grow the image all sides proportionally Test Pattern allows you to choose the Grid pattern the alignment pattern or none Reset to Default resets the image to factory resolu tion Illuminate Border turns the border outside the image green If the green border is visible the picture is either not properly sized or centered For more information on image alignment see 3 1 Aligning the Image on page 24 J Miscellaneous Options 4 Lamp Settings b 2 7 Image Alignment Pan Image Shrink Grow Reset to Default Illuminate Border Menu Options Position Main Menu Pict From the Main Menu select Position to Icture access the Picture Position menu Aspect Ratio Memory Audio Diagnostics Advanced Options p gt gt gt Program Information Picture Position Lise arrow keys to move image Horizontal Position 234 source PICTURE Vertical Position 24 CURTAIN 2 slZE POS SAVE SETUP iine Press the SIZE POS to access the Plcture Position menu directly ent
76. tics Advanced Options FT YF Program Information When the aspect ratio of the source picture and the aspect ratio of the display do not match Scale Mode and Justify are used to fit the picture onto the display With Scale Mode highlighted in the Aspect Ratio menu press enter or the right arrow on the remote control to access the drop down menu Scale Mode has the choices Fill All Crop Letterbox or Widescreen Fill All stretches the picture as necessary on one axis to fill the screen All of the picture is shown Letterbox fills the screen by stretching until the first edges touch the screen edges sides or top bottom and leaves the rest of the screen filled with the Cur tain color All of the picture is shown Crop fills the screen by stretching until the second edges touch the screen edges and crops the rest Some of the picture will be cut off Widescreen forces a 16 9 1 77 aspect ratio to display compressed DVDs correctly All of the picture is shown Justify moves the picture to the top middle or bottom or to the left center or right This has no function when the Scale Mode is Fill All One to One means show the picture without any scal ing If itis larger than the display s native resolution it will be cropped if it is smaller it will be shown with a black border This is most useful for 1280x720 reso lution in order to show the image with no scaling artifacts and only a slight loss of pixels around th
77. ting 30 name memory slot 67 native resolution 83 not addressed 70 not this display 70 adjusting semi automatically 30 computer sources adjusting to 61 digital sources adjusting to 62 video sources adjusting to 63 Line out Balance 68 O lost signal retry on 79 operating temperature 92 Lower Retaining Bracket 7 optical specifications 91 M Out 68 overscan 39 manual adjustment of levels for computer sources 61 ar overwriting a memory 67 manual black level 30 manual white level 30 P manufacturer s address 88 eius picture mechanical specifications 90 menu 60 picture menu 60 Plug and Play 76 plug and play 76 94 Position 64 81 power requirements 91 prev button 59 program information 83 R rear clearance 90 Red in Color Balance 37 regulatory information 88 remote control arrow keys 58 59 curtain 58 enter 59 freq phase 59 lamp 56 lamp on off 56 menu 56 on off 56 prev 59 save 57 setup 58 source 57 Removable I O cover 7 resolution native 83 retry on lost signal 79 RGB colorspace 34 RGB levels 61 RJ45 adapter 22 RJ45 to 9 pin adapter 22 RS232 straight thru cables for 86 Running Time 74 running time 74 S safety regulatory specifications 88 save button 57 menu 67 menu chain 57 scale mode 65 screen size 90 selecting the source 60 semi automatic level adjustment 30 semi automatic level adjustment for computer so
78. tor Most digital graphics cards will not output anything if they think they are connected to an analog monitor The choice defaults to digital but should be set by the user to match which input they are using on that connector Input levels Computer signals vary quite a bit from computer to computer They even vary between video outputs on the same video card Video sources vary more To make the TD61 respond correctly to these non standard sources we adjust Input Levels Input Levels for computer sources analog page 30 Input Levels for video sources page 32 How does Input Level relate to Color Balance If you have more than one TD61 in the area and you want them to display identical colors you need to adjust input levels and do color balancing You can do Input Levels first or you can do Color Balance first It doesn t matter But they must both be done Input Levels and Color Balance do not affect each other but they both affect the final picture Color Balancing the displays page 36 28 What does Input Level do For analog computer sources adjusting to the com puter s picture output means finding what that com puter means by black and white Black is supposed to be a voltage a zero coming from the computer s video card but it almost never is White is supposed to be a voltage of 0 7 volts but it usually isn t either The Input Level adjustment process asks you to provide a picture from the computer
79. ue Scale Uniformity Black Colors C Focus DO Gray Color Bars Logo on page 40 Recall 1 5 DO Bato Ci 18 126 34 01101942035 4 6412 CO zo 128 1 6 k 013102102 137 Os 0 22 136 0 38 Or Olis Oz 031 O 39 Je 116 24 32 0 40 017 025 133 O2 O18 026 134 O11 O19 M27 0135 Ma M12 O20 128 L136 Ms 013 21029 137 Os 0O14 O22 130 138 Er Oi 5 123 131 139 Os 01850290320 40 See Saving Your Work and Recall ing a Memory 97 58 Turns the curtain and off Curtain pattern is selected in the Miscellaneous menu See page 76 Mute mutes the audio Displays this message Source Analog RGB 1 Adjusting the Image and starts the process of adjusting the image performs those steps checked in the Auto Setup Options menu Changes the value of the high lighted item In some menus like Picture Position these buttons con trol left right movement The but ton moves you to the next menu when there is an arrow in the cur rent highlighted item See Picture on page 60 Picture source Analog Colorspace RGB Sync Type Separate H amp V Vertical Frequency 60 Hz MA Horizontal Frequency 43 38 kHz PICTURE Pixel Frequency 65 02 MHz Horizontal Resolution 1024 1 Vertical Resolution 768 CI Frequency 1344 SAVE SETUP Phase GH J 225 Sha
80. urces 61 serial port settings menu 78 status menu 70 setup button 58 setup summary menu 72 shipping weight kg 90 shipping weight lbs 90 signal lost retry on 79 slot memory 66 67 name of 67 source button 57 selecting 60 source computer adjusting to 30 source video adjusting to 32 Speaker Enable 68 specifications electrical 90 environmental 92 mechanical 90 optical 91 Status Display Light 76 status display light 76 straight thru cables for RS232 86 system hours 74 system Time 74 system time 74 T table analog mode horizontal resolution 84 mode ID 85 temperature operating 92 test pattern menu 71 this display alone 70 timeout menu 82 Torx wrench 7 treble 68 U unhide Color Balance menu 36 unit ID 78 V V position 82 ventilation requirement 90 video input amplitude 90 Video Controls 36 video source 32 video source adjusting to 32 volume 68 W Wall Mounting Bracket 7 waveforms RGB and YPbPr 35 weight 90 white balance color balance 75 White Level 36 white level manual adjusting 30 widescreen 65 wiring of connectors 86 wiring connectors 86 Y YPbPr colorspace 34 YPbPr levels 61 95 96 Limited Warranty Subject to the Limitations Exclusions and Disclaimers hereof InFocus Corporation InFocus warrants that the Rear Projection Display Device Lamps and Accessories hereinafter collectively or individually r
81. ve to do the manual or semi auto method once for each com puter source Save these settings in the SAVE menu See Memory Save on page 67 Then use RECALL to instantly bring it all back When to re adjust levels You should re adjust black and white levels when ever the computer is changed the video card in the computer is changed or you switch the source for this display to a different video card output in the same computer you change the electronics module ESE PRISER aE GAGES Auto Setup Options Picture Input Levels 31 3 2 Adjusting TD61 To Its Source 3 2 2 Adjusting to Video Sources Video adjustments are quite a bit like the controls on a television receiver Adjusting the picture 1 Select a video source in the Picture menu There is one composite video one component input and one S Video source available 2 Press PICTURE on the remote Now you have two choices e Adjust using any picture from the video source e Adjust using a standard color bar pattern from the SOUICE Adjusting with any picture This procedure must be done after you adjust color balance page 36 1 Choose pictures that have blacks and whites rep resented as well as a variety of colors 2 Adjust Contrast Brightness Saturation and Hue on one TD61 until it looks satisfactory 3 Adjust any other TD61 s so they have the same values for Contrast Brightness Saturation and Hue as

Infocus TD61 user manual

Contents

Download Pdf Manuals

Related Search

Related Contents