MOTOROLA Semiconductor MC10E143/MC100E143 handbook
Contents
1. 66 081 DETERMINED AT THE OUTERMOST 000 081 EXTREMES OF THE PLASTIC BODY 0025 064 EXCLUSIVE OF MOLD FLASH TIE BAR 0450 0456 1143 11 58 BURRS GATE BURRS AND INTERLEAD 0 450 0 456 1143 11 58 FLASH BUT INCLUDING ANY MISMATCH 0 042 0 048 107 121 BETWEEN THE TOP AND BOTTOM OF THE 0 042 0 048 107 121 PLASTIC BODY DIMENSION H DOES NOT INCLUDE DAMBAR 0042 e Lor E PROTRUSION OR INTRUSION THE DAMBAR 9 q9 Ec oe PI ROTRUSION S SHALL NOT CAUSE THE H amo 0430 1045 T 4032 000 102 ON TO BE GREATER THAN 0 037 0 940 THE DAMBAR INTRUSION S SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0 025 0 635 BQ N lt x lt c d x mo s gt 2 3 MOTOROLA MC10E143 MC100E143 Motorola reserves the right to make changes without further notice to any products herein Motorola makes no warranty representation or guarantee regarding the suitability of its products for any particular purpose nor does Motorola assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability including without limitation consequential or incidental damages Typical parameters which may be provided in Motorola datasheets and or specifications can and do vary in different applications and actual performance may vary o2. MOT ORBE 10 SEMICONDUCTOR TECHNICAL DATA 9 Bit Hold Register MC10E143 The MC10E 100E143 is a 9 bit holding register designed with MC100E143 byte parity applications in mind The E143 holds current data or loads new data with the nine inputs DO D8 accepting parallel input data e 700MHz Min Operating Frequency e 9 Bit for Byte Parity Applications e Asynchronous Master Reset 9 BIT HOLD e Dual Clocks REGISTER e Extended 100E VEE Range of 4 2V to 5 46V e 75kQ Input Pulldown Resistors The SEL Select input pin is used to switch between the two modes of operation HOLD and LOAD Input data is accepted by the registers a set up time before the positive going edge of CLK1 or CLK2 A HIGH on the Master Reset pin MR asynchronously resets all the registers to zero Hp AA k Pinout 28 Lead PLCC Top View mi SEL Dg D Dg D Vcco Qs FN SUFFIX PLASTIC PACKAGE CASE 776 02 24 23 22 21 LOGIC DIAGRAM D2 Dg D4 Vcco Q Q4 Q All Vcc and Vcco pins are tied together on the die PIN NAMES Do Dg Parallel Data Inputs SEL Mode Select Input CLK1 CLK2 Clock Inputs Master Reset Data Outputs No Connection Booo M MOTOROLA Motorola Inc 1996 REV 2 MC10E143 MC100E143 DC CHARACTERISTICS VEE VEE min to VEE max Vcc Vcco GND Symbol Characteristic i i i Input HIGH Current r j 1 ja j IEE Power Supply Current 10E 100E Symbol Characteristic fMAX Max Toggle F
3. o 135 Japan 03 81 3521 8315 MFAX RMFAX0 email sps mot com TOUCHTONE 602 244 6609 ASIA PACIFIC Motorola Semiconductors H K Ltd 8B Tai Ping Industrial Park INTERNET http Design NET com 51 Ting Kok Road Tai Po N T Hong Kong 852 26629298 MC10E143 D M MOTOROLA
4. requency 700 tPLH Propagation Delay to Output tPHL Clk 800 600 800 600 800 1000 MR 800 600 800 600 800 1000 50 100 300 300 150 300 300 1 Within device skew is defined as identical transitions on similar paths through a device MOTOROLA 2 2 MC10E143 MC100E143 OUTLINE DIMENSIONS FN SUFFIX PLASTIC PLCC PACKAGE CASE 776 02 ISSUE D 0 007 0 180 r U 0 007 0 010 0 250 S 0 007 0 180 0 007 0 180 0 007 0 180 0 004 0 100 SEATING PLANE 0 007 0 180 0 010 0 250 NOTES 1 DATUMS L M AND N DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE DIM G1 TRUE POSITION TO BE MEASURED AT DATUM T SEATING PLANE DIM R AND U DO NOT INCLUDE MOLD FLASH mu MILLIMETERS ALLOWABLE MOLD FLASH IS 0 010 0 250 0 485 0 495 1232 12 57 PER SIDE p 0 485 0 495 12 32 12 57 DIMENSIONING AND TOLERANCING PER ANSI 0165 0 180 420 157 Y14 5M 1982 CONTROLLING DIMENSION INCH 0090 0 110 229 27 HE PACKAGE TOP MAY BE SMALLER THAN 0 013 0 019 0 33 048 HE PACKAGE BOTTOM BY UP TO 0 012 0 050 BSC 1 27 BSC 0 300 DIMENSIONS R AND U ARE 0 026 0 032 0
5. vertime All operating parameters including Typicals must be validated for each customer application by customer s technical experts Motorola does not convey any license under its patent rights nor the rights of others Motorola products are not designed intended or authorized for use as components in systems intended for surgical implant into the body or other applications intended to support or sustain life or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur Should Buyer purchase or use Motorola products for any such unintended or unauthorized application Buyer shall indemnify and hold Motorola and its officers employees subsidiaries affiliates and distributors harmless against all claims costs damages and expenses and reasonable attorney fees arising out of directly or indirectly any claim of personal injury or death associated with such unintended or unauthorized use even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part Motorola and are registered trademarks of Motorola Inc Motorola Inc is an Equal Opportunity Affirmative Action Employer How to reach us USA EUROPE Locations Not Listed Motorola Literature Distribution JAPAN Nippon Motorola Ltd Tatsumi SPD JLDC 6F Seibu Butsuryu Center P O Box 20912 Phoenix Arizona 85036 1 800 441 2447 or 602 303 5454 3 14 2 Tatsumi Koto Ku Toky
Download Pdf Manuals
Related Search
MOTOROLA Semiconductor MC10E143/MC100E143 handbook