Home

TOSHIBA IK-DP01A/DP02A Manual

1. TOSHIBA INSTRUCTION MANUAL DOME CAMERA IK DP01A DP02A Please read this manual thoroughly before use and keep it handy for future reference Record in space provided below the Model No and the Seral No as found on the label on the bottom of this unit Model No IK DP01A DP02A Serial No Retain this information for future reference TABLE OF CONTENTS Important Safeguards 1 Features amp Description cccccccssssinciandecvesetncd anndeseceasastdecaaessennsees 3 AE a E A E E A E TT 3 3 COMPONENEHS oie eeecceceeccceccececeeeeeeeaeauaaaaneeeeaeeeeseeeeeererereeeeenenes 3 4 Part names and Locations ccccccccccesssceeceessseeeecessaneeeeeenans 4 Di GOMMECHONS srneci tiean SaaS 5 Gz OPSratiON scusano nana 7 i MenuiDieClory cacier ann es 22 8 Preset COMMAMNAS ccc cece ceesciveccevseecsecaesetestetenesesdeedeaesetendvatvances 25 9 Installation sescca eiaa aaaea 26 10 Switch Setting sivelcs ke celtavee tirin iresi 29 11 SP CIFICATIONS sreriimerniiasae ennen eene aeaaee aa Ee EE 32 10 11 IMPORTANT SAFEGUARDS Road Instructions All the safety and operating instructions should be read before the product is operated Retain Instructions The safety instructions and instruction manual should be retained for future reference Heed Warnings All warnings on the product and in the instruction manual should be adhered to Follow Instructions All operating and use instruction
2. AUTO FLIP ON PROPORTINAL P T ON SCAN LIMIT STOPS OFF MANUAL LIMIT STOPS OFF PARK TIME MIN OMIN AUTO PATROL P1 gt 0OFF SCAN SPEED 5DEG S SCAN TILT ANGLE 30DEG STOP TIME 10SEC MAX SPEED 300DEG S PRESET TITLES MENU TITLE INPUT TITLE POSITION DOWN OTHERS MENU POWER UP FREEZE ACTIVITY OFF LOAD FACTORY DEFAULT PARK 23 FOCUS SETUP MENU MODE AUTO ACTIVE TIME 5S INTERVAL TIME 5S SENSITIVITY NORMAL MODE FULL AUTO AUTO SLOW SHUTTER OFF SHUTTER SPEED 1 60 AE COMPENSATION 0 BACK LIGHT COMP OFF LINE LOCK MENU MODE OFF LINE PHASE 7 1 MENU LIST AND SETTINGS Sub Menu1 Sub Menu2 Contents Default Auto Exposure Mode Full Auto Shutter Priority Full Auto Auto Slow Shutter On Off Shutter Speed 1 1 1 10000 22step AE Compensation 7 47 Back Light Comp On Off Day Night Auto Manual Zoom Limit x18 36 72 144 216 Sharpness Line Lock Mode 0 15 Line Phase Pan Tilt Setup Auto Flip Propoutional P T Scan Limit Stops Manual Limit Stops On Off Park Time Minutes 0 720min Auto Patrol Preset1 On Off Preset2 On Off Preset64 On Off Scan Speed 1 90 degree s 5 Scan Tilt Angle 0 90 degree 30 Stop Time 10 60 sec 10 Max Speed 30 300 degree s 300 Preset Titles Title input Title Position It is to 20 characters to eac
3. lt CAMERA SETUP gt POWER UP PARK lt PAN TILT SETUP gt gt FREEZE ACTIVITY ON lt PRESET TITLES gt LOAD FACTORY DEFAULT gt lt OTHERS gt EXIT To set STOP TIME 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to OTHERS and press the OPEN button to access the menu 3 Position the cursor next to FREEZE ACTIVITY and press the OPEN button to move 21 Ee the cursor to the right 4 Move the joystick up or down to set freeze activity to ON or OFF 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 7 3 LOAD FACTORY DEFAULTS The factory default settings can be loaded MAIN MENU OTHERS MENU lt CAMERA SETUP gt POWER UP PARK lt PAN TILT SETUP gt FREEZE ACTIVITY ON lt PRESET TITLES gt LOAD FACTORY DEFAULT gt lt OTHERS gt EXIT To set LOAD FACTORY DEFAULT 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to OTHERS and press the OPEN button to access the menu 3 Position the cursor next to LOAD FACTORY DEFAULT and press the OPEN button twice to load factory default settings 222s 7 Menu Directory Top menu lt CAMERA SETUP gt lt PAN TILT SETUP gt lt PRESET TITLES gt lt OTHERS gt EXIT CAMERA SETUP MENU lt FOCUS gt WB ATW lt AE gt ZOOM LIMIT SHARPNESS lt LINE LOCK gt x18 IRIS 10 CLOSE PAN TILT SETUP MENU
4. Pan Range 360degrees continuous Tilt Range 85 degrees Manual Pan Speeds 0 1 90 s Manual Pan Speeds turbo 150 s Manual Tilt Speeds 0 1 45 s Pan 300 s max set in menu Tilt 200 s Preset Speeds 6 3 SCAN FUNCTIONS AUTO SCAN The dome camera can perform an auto scan operation during power up and by direct control from a keyboard When scan limit stops ARE NOT set The dome camera will pan continuously until a manual operation from the keyboard is performed pan tilt iris control or focus When scan limit stops ARE set The dome camera will pan continuously between scan limit stops until a manual operation from the keyboard is performed pan tilt iris control or focus To set scan limit stops refer to SCAN LIMIT STOPS under PAN TILT SETUP Zoom At power up the zoom will be fully zoomed out When an auto scan is started directly from the keyboard the zoom will maintain the last magnification Tilt At power up the tilt is set up by the menu To set the tilt angle refer to SCAN TILT ANGLE under PAN TILT SETUP When an auto scan is started directly from the keyboard the tilt will maintain the last tilt angle FRAME SCAN The dome camera can perform a frame scan operation during power up and by direct control from a keyboard Operation of zoom and tilt is the same as in Auto Scan When scan limit stops ARE NOT set The dome camera will move in 45 degree increment
5. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE e CAUTION CONNECT 24V AC UL LISTED CLASS 2 The exclamation point within an POWER SUPPLY equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance FIELD INSTALLATION MARKING WORDED THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL CODES INFORMATION This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipmetn in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense USER INSTALLER CAUTION Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by the party 1 Features and description IK DP01A DP02A has following function Quick Install D
6. CABLE CONNECT GROUND ON ONE END ONLY IK DP01A Rx IK DPOQ1A Rx 6 Operation Power On display TOSHIBA IK DP01A VERSION When the dome camera powers up the software PROTOCOL TOSHIBA P version selected protocol and other information ADDRESS 1 are displayed on the monitor COMM 4800 N 8 1 6 1 ACCESSING THE MENU Accessing the menu varies with the model controller being used Several controllers are listed below Please refer to your model s instructions for information on inputting commands KBD200 300 300V direct Input 95 using the numeric keypad Hold down the PRESET button until the MENU screen is displayed KBD200 300 300V CM6700 mode Input 95 using the numeric keypad Hold down the PRESET button until the Edit LABEL screen of CM6700 is displayed Press the TILT UP DOWN button until SET is chosen Press the ACK button to display the MENU screen MPT9500 Input 95 using the numeric keypad Press the PRESET SET button Press the F2 button to display the MENU screen 6 2 PAN TILT FUNCTIONS Manual PAN Manual Pan is controlled from a keyboard and the speed ranges from 0 1 degrees sec to 90 degrees sec depending on the joystick position In turbo mode the speed is 150 degree sec However this speed is limited when Proportional P T is ON Manual TILT Manual Tilt speed ranges from 0 1 degrees sec 45 degrees sec However this speed changes when Proportional P T is ON sa
7. One Push Trigger Auto Focus is available Menu MAIN MENU CAMERA MENU FOCUS MENU gt lt CAMERA SETUP gt gt lt FOCUS gt MODE AUTO lt PAN TILT SETUP gt WB ATW ACTIVE 5S lt PRESET TITLES gt lt AE gt INTERVAL TIME 5S lt OTHERS gt ZOOM LIMIT X18 SENSITIVITY NORMAL EXIT SHARPNESS 10 lt LINE LOCK gt The Focus control has four options Manual Auto Interval Zoom Trigger In the manual mode the IK DP01A DP02A focus will be directly controlled with the near and far controls When the camera is in Auto Mode pressing the near and far controls will place the camera in manual mode until there is a zoom or pan tilt function In Interval mode the camera will switch between auto focus and manual focus according to the Active Time and Interval Time respectively Active Time auto gt Interval Time manual gt Active Time auto gt Interval Time manual The interval and active times can be set from 1s to 255s In Zoom Trigger mode the camera remains in manual mode unless there is a zoom function and will return to manual mode after the zoom function is completed The sensitivity of the Auto Focus can be set to NORMAL or LOW To change the Focus options 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to CAMERA SETUP and press the OPEN button to access the Camera menu 3 Position the cursor next to FOCUS and press the OPEN button to access the Focus menu 4 Positi
8. bottom of the screen 7 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 7 OTHERS MENU 6 7 1 POWER UP During Power Up the dome camera can be set to start in various modes PARK The dome camera will move to Preset 1 position AUTO SCAN The dome camera will perform an auto scan operation FRAME SCAN The dome camera will perform a frame scan operation RANDOM SCAN The dome camera will perform a random scan operation 20 AUTO PATROL The dome camera will perform an auto patrol operation DEFAULT The dome camera will move to the mechanical reset point MAIN MENU TITLE MENU lt CAMERA SETUP gt gt POWERUP PARK lt PAN TILT SETUP gt FREEZE ACTIVITY ON lt PRESET TITLES gt LOAD FACTORY DEFAULT gt lt OTHERS gt EXIT To set POWER UP MODE 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to OTHERS and press the OPEN button to access the menu 3 Position the cursor next to POWER UP and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to set the power up mode 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 7 2 FREEZE ACTIVITY During frame scan random scan or auto patrol a stop time from 10 sec to 60 sec can be set During scanning the camera will not move for the specified time at each stop MAIN MENU OTHERS MENU
9. gt Dome drive X18 Lens 5 Connections Basic connection Direct mode 24V AC UL listed class 2 power supply RS422 ia 4 AC Adaptor Monitor Keyboard Make sure to connect to a power supply that allows for at least 35W consumption RS422 Pin Out OM RX RX TX 2 wire Om RX RX _ TX controller Pj RX 2nd Om Tx TX __ RX Dome Camera In the direct mode Tx of the communication line from KBD is connected to Rx of the dome and Tx is connected to Rx of the dome When connecting between two or more dome cameras by the daisy chain Tx of the first dome and Rx of the following dome are connected and Tx of the first dome and Rx of the following dome are connected Note KBD200 300 300V CM6700 and MPT9500 are the products of Pelco CM6700 mode Video CM6700 SCU REMOTE KEYBOARDS CM6700 SCU LOCAL KEYBOARD fo E COM1 1 6 oo 0 090 O 0O Og COM2 7 12 12345678 9101112 12 PIN PLUG IN SSO SSSOSOGSS oq DGG 6 BJE 40 NOTE TO PROPERLY SHIELD DATA
10. numeric keypad Hold down the PRESET button for 5 seconds to set the preset KBD200 300 300V CM6700 mode Input the desired preset number using the numeric keypad Hold down the PRESET button until the Edit LABEL screen of CM6700 is displayed Press the TILT UP DOWN button until SET is chosen Press the ACK button to set the preset 25 MPT9500 Input the desired preset number using the numeric keypad Press the PRESET SET button Press the F2 button to set the preset 8 2 PERFORMING PRESET OPERATIONS KBD200 300 300V direct and CM6700 mode Input the desired preset number using the numeric keypad Press the PRESET button to perform the preset MPT9500 Input the desired preset number using the numeric keypad Press the PRESET GO button to perform the preset 9 Installation JK H01A is a housing for ceiling mount of the Toshiba dome camera 1 IK DP01A Installation procedure 1 Carefully inspect to insure all parts are present and remove all parts from the box 2 A template is included for ease in cutting the mounting hole First locate a position in the ceiling for a 9 020 08 2292mm hole to be drilled Trace around the template then cut a hole in the ceiling Lock following the trace lines Note The sas thickness of a ceiling to which this housing can be attached is 0 08 1 77 2 45mm 3 Remove the dome cover To separate the dome cover from the housing turn the cover to the left with both hands Thi
11. right 4 Move the joystick up or down to set the number of minutes 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 5 6 AUTO PATROL The Auto Patrol feature will repeat a pattern of up to 64 presets Limit stops are ignored during Auto Patrol To enable AUTO PATROL 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu 3 Position the cursor next to AUTO PATROL and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to scroll through the presets Move the joystick left or right to turn the preset ON or OFF 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 5 7 SCAN SPEED The SCAN SPEED for auto scan random scan and frame scan can be set from 1 90 degrees sec However this speed is limited by MAX SPEED To set SCAN SPEED 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu 3 Position the cursor next to SCAN SPEED and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to set the speed 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 18 6 5 8 SCAN TILT ANGLE The tilt ang
12. the CLOSE button 6 4 5 SHARPNESS CONTROL Menu MAIN MENU CAMERA MENU gt lt CAMERA SETUP gt lt FOCUS gt lt PAN TILT SETUP gt WB ATW lt PRESET TITLES gt lt AE gt lt OTHERS gt gt ZOOM LIMIT X18 EXIT SHARPNESS 10 lt LINE LOCK gt The sharpness can be controlled from 0 15 with 15 being the sharpest To change the SHARPNESS 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to CAMERA SETUP and press the OPEN button to access the Camera menu 3 Position the cursor next to SHARPNESS and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to select the sharpness level 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 4 6 LINE LOCK CONTROL The dome camera can be synchronized with the power supply frequency Menu Line Lock can be set to ON or OFF The Line Lock Phase can be set from 0 200 degrees MAIN MENU CAMERA MENU LINE LOCK gt lt CAMERA SETUP gt lt FOCUS gt MODE OFF lt PAN TILT SETUP gt WB ATW LINE PHASE 180 lt PRESET TITLES gt lt AE gt lt OTHERS gt ZOOM LIMIT X18 EXIT SHARPNESS 10 gt lt LINE LOCK gt To change the LINE LOCK options 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to CAMERA SETUP and press the OPEN button to access the Camera menu 3 Position the cursor next to LINE LOCK and pres
13. ATION APPLIES TO DAMAGES OF ANY KIND INCLUDING ANY DIRECT OR INDIRECT DAMAGES LOST PROFITS LOST SAVINGS OR OTHER SPECIAL INCIDENTAL EXEMPLARY OR CONSEQUENTIAL DAMAGES WHETHER FOR BREACH OF CONTRACT TORT OR OTHERWISE OR WHETHER ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH PRODUCT EVEN IF TAIS ITS PARENT COMPANY OR AN ASP HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR SOME PRODUCTS SO THE ABOVE LIMITATINS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE THIS LIMITED WARRANTY SHALL BE VOID IF THE PRODUCT OR PARTS HAVE BEEN SUBJECTED TO MISUSE ABUSE ACCIDENT IMPROPER INSTALLATION IMPROPER MAINTENANCE OR USE IN VIOLATION OF ISD S WRITTEN INSTRUCTIONS OR WHERE THE PRODUCT HAS BEEN ALTERED OR MODIFIED WITHOUT ISD S PRIOR AUTHORIZATION OR UPON THE REMOVAL OR ALTERATION OF ISD S FACTORY SERIAL NUMBER LABOR SERVICE CHARGES FOR PRODUCT INSTALLATION SET UP AND ADJUSTMENT OF CONTROLS ARE NOT COVERED BY THIS LIMITED WARRANTY No person agent distributor dealer authorized service provider or company is authorized to change modify or extend the terms of this Limited Warranty in any manner whatsoever The time within which an action must be commenced to enforce any obligation of ISD arising under thi
14. Manual Limit Stop can be set The limit stops must be greater than 10 degrees apart To enable MANUAL LIMIT STOPS 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu 3 Position the cursor next to MANUAL LIMIT STOPS and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to select ON or OFF 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button To set MANUAL LIMIT STOPS 1 Set MANUAL LIMIT STOPS to ON and exit menu 2 Position the camera for the LEFT LIMIT STOP 3 Enter 90 preset MANUAL LEFT LIMIT will be displayed on screen 4 Position the camera for the RIGHT LIMIT STOP If the right limit stop is less than 10 degrees from the left limit stop NOT ACCEPT will be displayed on screen 5 Enter 91 preset MANUAL RIGHT LIMIT will be displayed on screen 6 5 5 PARK TIME MINUTES After a programmed number of minutes of inactivity the dome camera will park to preset 1 The Park Time Minutes can be set from 1 720 minutes Setting it to 0 will disable the feature 417 To set PARK TIME MIN 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu 3 Position the cursor next to PARK TIME MIN and press the OPEN button to move the cursor to the
15. approx 48degree wide limit approx 2 7degree tele limit Internal Line lock AC Line lock phase adjustable Min Illumination 0 7 lux typ 1 60 0 05 lux typ 1 4 0 01 lux 1 4 IR Cut OFF IK DP02A only S N Ratio more than 50dB Resolution 480 TV lines typ Electronic Shutter 1 4 to 1 10000 sec White Balance Auto ATW One Push WB Gain Auto AE Control Full Auto Shutter Priority Manual Back Light Compensation On Off Auto Slow Shutter On Off On max1 4sec Focusing System Auto Interval Zoom Trigger Manual Video Output NTSC VBS 1 0Vp p Sync Negative 75 ohm 99 Mechanical Pan Range 360degrees continuous Tilt Range 85degrees Manual Pan Speeds 0 1 90 s Manual Pan Speeds turbo 150 s Manual Tilt Speeds 0 1 45 s Preset Speeds Pan 300 s Tilt 200 s Proportional P T Provided Remote Control VF RS 422 receive onl Protocol Toshiba P D Dip sw selectable Data rate 1200 2400 4800 9600bps Dip sw selectable 33 LIMITED WARRANTY CCD SECURITY CAMERA The Imaging Systems Division of Toshiba America information Systems Inc ISD makes the following limited warranties with regard to this DOME Camera Product These limited warranties extend to the Original End User You r One 1 Year Limited Warranty of Labor and Parts ISD warrants that t
16. ater d If the video product does not operate normally by following the operating instructions in the instruction manual Adjust only those controls that are covered by the instruction manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation e If the video product has been dropped or the cabinet has been damaged f When the video product exhibits a distinct change in performance this indicates a need for service Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer of have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards Safety Check Upon completion of any service or repairs to this video product ask the service technician to perform safety checks to determine that the video product is in proper operating condition e The CAUTION label shown on the left is attached on the camera A RISK OF ELECTRIC SHOCK A DO NOT OPEN The lightening flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons WARNING
17. ely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs screws and the point where they exit from the product 12 13 14 15 16 17 18 Lightning For added protection for this video product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the power supply and cable system This will prevent damage to the video product due to lightning and power line surges Overloading Do not overload power supply and extension cords as this can result in a risk of fire or electric shock Object and Liquid Entry Never push objects of any kind into this video product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electrical shock Never spill liquid of kind on the video product Servicing Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Damage Requiring service Disconnect this video product from the power supply and refer servicing to qualified service personnel under the following conditions a when the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the video product c If the video product has been exposed to rain or w
18. esign Cuts Installation Time in Half 480 Lines Horizontal Resolution 300 Degree Second Pan 18X Optical 12X Digital Zoom 0 05 Lux Minimum Illumination IK DP01A 0 01 Lux Minimum Illumination IK DP02A 50dB Signal To Noise Ratio 64 Position Preset Auto Flip Proportional Zoom 2 Cautions 1 In order to protect the camera avoid placing or using it under direct sunlight rain or dust 2 Avoid touching the zoom lens with your fingers If necessary use a soft cloth moistened with alcohol to wipe off any dust 3 When the camera is not in use keep the lens cap attached to protect the zoom lens 4 Avoid aiming the camera at the sun 5 Avoid shooting the smear at intense light Intense light such as a spotlight may cause a bloom or smear A vertical stripe may appear on the screen However this is not a malfunction 6 Install the camera away from video noise If cables are wired near electric lighting wires or a TV set noise may appear in images In this event relocate cables or reinstall equipment 3 Components 1 Dome base 2 Dome drive 3 Accessories Instruction manual Install screw 3PCS 4 Part names and Locations Terminal for Control RS 422 Terminal for Power 24VAC only BNC connector for Video out Install brackets 3 legs Vs Notch for install gt Dome base Label for install oj x 89 Screw for cover lock Reserved
19. fix the dome base to the housing Fig 5 IK DP01A dome drive install 16 After setting up DIP SW in the top of the dome See 4 switch setting connect the support wire to the hook of the dome base Fig 6 1 17 A signal cable is inserted in the connector of a dome base Fig 6 18 Be sure the direction of the connector is correct at this time 19 To lock the dome drive to the dome base line up the notch with the label and turn to the right with both hands Fig 6 28 JK HO1A dome cover install 20 To lock the dome cover insert the support wire and turn to the right with both hands Fig 7 Fig 8 Fig 7 Fig 8 21 The installation is complete 10 Switch Setting There are two switches which must be set up One is the switch which the top of a dome drive has and another is the switch which the top of a dome base has Dome drive switch DIP switch It is necessary to set a peculiar camera address protocol and bit rate as each camera Please set up a camera address according to the following table 29 1 SW1 Camera Address Camera Address bot7 Off 30 Camera Address 1 x bit1 Status 2 x bit2 Status 4 x bit3 Statu
20. h Preset number Up Down All Blank Others Power up Default Park Auto Scan Frame Scan Random Scan Auto Patrol Freeze Activity On Off Load Factory Default IK DP02A only 942 8 Preset Commands The dome camera can set and perform various preset commands The following table lists the preset number and whether is can be set SET or performed GO Presets 1 32 and 35 66 are user presets Please refer to your model s instructions for information on inputting preset commands Preset Number Function 1 32 SET GO Preset position 1 32 33 GO Flip 34 GO Home return to 0 pan position 35 66 SET GO Preset position 35 66 GO Begin Auto patrol GO Backlight compensation ON GO Backlight compensation OFF GO One push WB GO One push trigger AF Software version Display P T Initialize IR Cut filter ON IK DP02A Only IR Cut filter OFF IK DP02A Only Set manual left limit stop Set manual Right limit stop Set Scan Left Limit Stop Set Scan Right Limit Stop Enter Menu Mode Stop Scan Begin Random Scan Begin Frame Scan Begin Auto scan 8 1 PROGRAMMING PRESETS Programming presets varies with the model controller being used Several controllers are listed below Please refer to your model s instructions for information on inputting preset commands KBD200 300 300V direct Input the desired preset number using the
21. his Product will perform in accordance with specifications for a period of one 1 year from the date of purchase by the Original End User During this one 1 year period ISD will repair or replace the Product if it does not perform as warranted In order to take advantage of this Limited Warranty You must a deiver the Product to an ISD Authorized Service Provider ASP and b pay all transportation and insurance charges for shipment of the Product to the ASP ISD reserves the right to substitute factory refurbished parts in place of those in need of repair Instruction Manual Owner s Manual You should read the Instruction Manual Owner s Manual thoroughly before operating this Product Before seeking warranty service you should check the troubleshooting guide in the Instruction Manual Owner s Manual and follow the instructions to correct the problem How to Obtain Warranty Service Step by step Procedures To obtain warranty service You should 1 Contact Toshiba at 877 855 1349 for operation or installation assistance 877 855 1FIX 2 Contact an ASP for warranty service with in thirty 30 days after the Product fails to comply with specifications 3 Arrange for shipment of the Product to a Toshiba Authorized Service Provider 4 Securely pack the Product in the original carton and extemal shipping pack include a letter explaining the problem with a copy of the bill of sale or proof of purchase 5 Prepay all transportation a
22. le of the dome camera for auto scan random scan and frame scan can be set from 0 85 degrees 0 degrees is straight down To set SCAN TILT ANGLE 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu 3 Position the cursor next to SCAN TILT ANGLE and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to set the tilt angle 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 5 9 STOP TIME During frame scan random scan or auto patrol a stop time from 10 sec to 60 sec can be set During scanning the camera will not move for the specified time at each stop To set STOP TIME 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu 3 Position the cursor next to STOP TIME and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to set the stop time 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 5 10 MAX SPEED The maximum speed of Pan Tilt functions can be set from 30 degrees sec to 300 degrees sec The max speed controls global Pan Tilt speeds To reduce rotation noise a lower speed is recommended To set MAX SPEED 1 Enter 95 preset to access the mai
23. ll Be Menu MAIN MENU CAMERA MENU AE MENU gt lt CAMERA SETUP gt lt FOCUS gt MODE FULL AUTO lt PAN TILT SETUP gt WB ATW AUTO SLOW SHUTTEROFF lt PRESET TITLES gt gt lt AE gt SHUTTER SPEED 1 60 AE COMPENSATION 0 lt OTHERS gt ZOOM LIMIT EXIT SHARPNESS BACK LIGHT COMP OFF lt LINE LOCK gt DAY NIGHT AUTO M IK DPO2A only AE Auto Exposure mode can be set to FULL AUTO or SHUTTER PRIORITY In FULL AUTO mode the shutter is fixed at 1 60 sec and the camera will automatically adjust the iris according to the light level In FULL AUTO mode the iris can be controlled manually but will return to FULL AUTO if there is a zoom or pan tilt operation In SHUTTER PRIORITY the shutter can be varied from 1 sec 1 10000 in 22 steps Auto Slow Shutter can be set ON or OFF AE Compensation can be set from 7 to 7 Back light compensation can be set ON or OFF Back light compensation can be set directly using a KBD controller 71 PRESET ON 72 PRESET OFF Day Night mode can be set AUTO or MANUAL MANUAL mode can be set directly using a KBD controller 88 PRESET IR Cut ON 89 PRESET IR Cut OFF An infrared IR Cut Filter can be disengaged from the image path for increased sensitivity in low light environments This function will automatically engage depending on the ambient light allowing the camera to be effective in day night environments IK DPO2A only To change the AE options 1 En
24. n menu 2 Position the cursor gt next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu 3 Position the cursor next to MAX SPEED and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to set the maximum speed 19 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 6 PRESET TITLES SETUP Titles can be set for up to 64 presets pan tilt position and zoom Titles can be up to 20 characters in length and can be displayed at the top or bottom of the screen MAIN MENU TITLE MENU lt CAMERA SETUP gt gt TITLE INPUT lt PAN TILT SETUP gt gt lt PRESET TITLES gt TITLE POSITION UP lt OTHERS gt EXIT To set PRESET TITLES 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to PRESET TITLES and press the OPEN button to access the Title menu 3 Press the OPEN button to move the cursor down to the title number Move the joystick up or down to scroll through title numbers 4 Move the joystick to the right to input the title Move the joystick up or down to scroll through characters 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 Move the joystick down to TITLE POSITION and press open to choose UP or DOWN position of the title UP will display the title at the top of the screen and DOWN will display the title at the
25. nd insurance costs Questions If you have any questions please check our wed site at http Awww toshiba com taisisd security Your Responsibilities This Limited Warranty is subject to the following conditions 1 You must provide the bill of sale or proof of purchase at the time that warranty service is required 2 You must notify an ASP within theiny 30 days after you discover that the product does not perform in accordance with specifications during the Limited Warranty period 3 All Warranty Service of this product must be by an ISD Authorized Service Provider 4 You must pack the Product in its original carton using the original packing material then insert the original carton containing the Product into another carton with additional packing materia before shipping the Product to an ASP DISCLAIMERS ALL OTHER EXPRESS OR IMPLIED WARRANTIES ON THIS PRODUCT INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE YOUR SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OF REPLACEMENT OF THE PRODUCT IN NO EVENT WILL ISD OR ITS PARENT COMPANY OR ANY ASP BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT THIS LIMIT
26. on the cursor next to the desired option and press the OPEN button to move the cursor to the right 5 Move the joystick up or down to select option setting 6 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button eal i ee 6 4 2 WHITE BALANCE CONTROL Direct The White Balance can be set by One Push Trigger operation Menu MAIN MENU CAMERA MENU gt lt CAMERA SETUP gt lt FOCUS gt lt PAN TILT SETUP gt WB ATW lt PRESET TITLES gt lt AE gt lt OTHERS gt gt ZOOM LIMIT X18 EXIT SHARPNESS 10 lt LINE LOCK gt The White Balance can be set to ATW Auto Tracking White AUTO ONE PUSH WB ATW automatically adjusts the white balance for color temperatures from 2000K to 10000K AUTO automatically adjusts the white balance for color temperatures from 3000K to 7500K ONE PUSH WB can be set using 73 PRESET from a controller To change the White Balance 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to CAMERA SETUP and press the OPEN button to access the Camera menu 3 Position the cursor next to WB and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to select ATW AUTO or ONE PUSH WB 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 4 3 AE CONTROL Direct The Iris can be controlled directly using OPEN or CLOSE controls Pa
27. s 8 x bit4 Status 16 x bit5 Status 32 x bit6 Status 64 x bit7 Status 128 x bit8 Status bit Status On 1 Off 0 ex Camera Address 200 1 x O Off 2 x O Off 4 x O Off 8 x 1 On 16 x O Off 32 x O Off 64 x 1 On 128 x 1 On 8 64 128 200 Off Off Off On Off Off On On 2 SW2 bit1 2 Protocol Protocol TOSHIBA P TOSHIBA D Reserve Reserve2 3 SW2 bit3 4 Bit Rate Protocol 1200bps 2400bps 4800bps 9600bps Dome base switch S301 This is RS422 termination switch located near the BNC connector In daisy chain operation system the farthest dome from the controller is turned ON For example when the controller is connected with three dome cameras in the direct mode the only furthest dome camera from a controller is turned ON The other dome camera is turned OFF It is OFF at the time of shipment ON and OFF are as in a figure 31 ON POWER TERMINAL BNC Connector 10 Specifications Overall Temperature of operation 32 to 122 F 0 to 50 C Preservation temperature 4 to 140 F 20 to 60 C Weight 1 75 k Power supply g AC24V 10 60Hz Camera Image Sensor 20W 1 4 type IT CCD High Sensitive CCD Number of Effective Pixels 768 H x 494 V Lens Digital Zoom 18xZoom f 4 1 to 73 8mm F1 4 to F3 0 12x 216x with optical zoom Angle of View H Sync System
28. s called stops horizontally until a manual operation from the keyboard is performed pan tilt iris control or focus See figure below stop stop stop time stop When scan limit stops ARE set The dome camera will move in 45 degree increments horizontally within the limit stops until a manual operation from the keyboard is performed pan tilt iris control or focus See figure below Right Limit Left Limit A gt 8B C E 1 gt E gt D RANDOM SCAN The dome camera can perform a random scan operation during power up and by direct control from a keyboard Operation of zoom and tilt is the same as in Auto Scan When scan limit stops ARE NOT set The dome camera will move between random stops and random tilt angles until a manual operation from the keyboard is performed pan tilt iris control or focus See figure below stop stop G C stop stop A ex A C H E G B D F When scan limit stops ARE set The dome camera will move between random stops and random tilt angles within the limit stops until a manual operation from the keyboard is performed pan tilt iris control or focus See figure below stop stop Right Limit Left Limit stop A ex A D C B E 6 4 CAMERA SETUP 10 6 4 1 FUCUS CONTROL Direct The focus can be controlled directly using near or far focusing controls The focus control has 4 varying speeds
29. s Limited Warranty or under any statute or law of the United States or any state thereof is herby limited to one 1 year from the date You discovered should have discovered the problem This limitation does not apply to implled warranties arising under state law Some states do not permit limitation of the time within which You may bring an action beyond the limits provided by state law so the above provision may not apply to You This Limited Warranty gives You specific legal rights and You may also have other rights which vary from state to state TOSHIBA AMERICA INFORMATION SYSTEMS INC Imaging Systems Division TOSHIBA 34
30. s dome cover is connected to the top housing with the wire Fig 1 Fig 1 4 Loosen the lock screw according to ceiling board thickness for attaching to the ceiling 5 The IK DP01A is temporarily attached to the topside of the housing using the screws that were included with the IK DPO1A 6 Do not fully tighten the screw 26 JK HO1A top housing install 7 Two support arms are contained inside and attaches to the ceiling Fig 2 8 Put the video cable power cable and the communication cable inside the housing from the hole on the topside Break a hole in the center of the housing and let the cable pass through 9 Push out the support arms so that they hold onto the ceiling Fig 3 10 A lock screw is fastened from the bottom and the top housing is fixed to a ceiling Fig 4 297 Support wire is fixed here Support Arms Fig 3 11 Use a support wire for safety 12 The hole that fixes a support wire is on the side Note The support wire is not attached JK DP01A dome base install 13 Attach the video cable included with the dome accessories to the video connector of a dome base Note Do not connect a thick coaxial cable to a dome camera There is a possibility of damaging a connector Be sure to use the cable included in the dome accessories 14 Communication cables are directly inserted in the terminal of the dome base 15 Tighten the screw to
31. s should be followed Cleaning Disconnect this video product from the power supply before cleaning Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards Water and Moisture Do not use this video product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like Accessories Do not place this video product on an unstable cart stand tripod bracket or table The video product may fall causing serious injury to a child or adult and serious damage to the product Use only with stand tripod bracket or table recommended by the manufacturer or sold with the video product Any mounting of the product should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer Ventilation This video product should never be placed near or over a radiator or heat register This video product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to Power Sources This video product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your location consult your product dealer Power Cord Protection Power Supply cords should be routed so that they are not lik
32. s the OPEN button to access the Line Lock menu 4 Position the cursor next to the desired option and press the OPEN button to move the cursor to the right 5 Move the joystick up or down to select the option setting 6 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 15 6 5 PAN TILT SETUP 6 5 1 AUTO ELIP The Auto Flip feature allows the tilt to rotate 180 degrees and reposition itself for continuous viewing of a moving object directly beneath the dome To enable AUTO FLIP 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu 3 Position the cursor next to AUTO FLIP and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to select ON or OFF 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 5 2 PROPORTIONAL P T Proportional P T controls the pan and tilt speeds according to the amount of zoom At telephoto settings the pan and tilt speeds will be slower to keep the image from moving too fast on the monitor To enable PROPORTIONAL P T 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu 3 Position the cursor next to PROPORTIONAL P T and press the OPEN button to move the cur
33. sor to the right 4 Move the joystick up or down to select ON or OFF 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button 6 5 3 SCAN LIMIT STOPS When a Scan Limit Stop is reached during random frame or auto scan the dome camera will reverse direction A Left Scan Limit Stop and Right Scan Limit Stop can be set The limit stops must be greater than 10 degrees apart To enable SCAN LIMIT STOPS 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to PAN TILT SETUP and press the OPEN button to access the Pan Tilt menu 16 3 Position the cursor next to SCAN LIMIT STOPS and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to select ON or OFF 5 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button To set SCAN LIMIT STOPS 1 Set SCAN LIMIT STOPS to ON and exit menu 2 Position the camera for the LEFT LIMIT STOP 3 Enter 92 preset SCAN LEFT LIMIT will be displayed on screen 4 Position the camera for the RIGHT LIMIT STOP If the right limit stop is less than 10 degrees from the left limit stop NOT ACCEPT will be displayed on screen 5 Enter 93 preset SCAN RIGHT LIMIT will be displayed on screen 6 5 4 MANUAL LIMIT STOPS When a Manual Limit Stop is reached during a manual joystick pan the camera will stop A Left Manual Limit Stop and Right
34. ter 95 preset to access the main menu 2 Position the cursor gt next to CAMERA SETUP and press the OPEN button to access the Camera menu 3 Position the cursor next to AE and press the OPEN button to access the AE menu 4 Position the cursor next to the desired option and press the OPEN button to move the cursor to the right 5 Move the joystick up or down to select option setting 6 To accept the selection press the OPEN button or to cancel the selection press the CLOSE button lt 13 6 4 4 ZOOM CONTROL Direct The zoom feature has 4 varying speeds The IK DP01A zoom feature can be controlled directly for Wide angle or Telephoto angle Menu MAIN MENU CAMERA MENU gt lt CAMERA SETUP gt lt FOCUS gt lt PAN TILT SETUP gt WB ATW lt PRESET TITLES gt lt AE gt lt OTHERS gt gt ZOOM LIMIT X18 EXIT SHARPNESS 10 lt LINE LOCK gt A zoom limit can be set to x18 x36 x72 x144 and x216 The maximum optical zoom is x18 x36 to x216 are the values for electronic zoom To change the zoom limit 1 Enter 95 preset to access the main menu 2 Position the cursor gt next to CAMERA SETUP and press the OPEN button to access the Camera menu 3 Position the cursor next to ZOOM LIMIT and press the OPEN button to move the cursor to the right 4 Move the joystick up or down to toggle between zoom limits 5 To accept the selection press the OPEN button or to cancel the selection press

TOSHIBA IK-DP01A/DP02A Manual

Contents

Download Pdf Manuals

Related Search

Related Contents