Home

SIRIUS Satellite Radio USER MANUAL

1. 3 Press lt or P gt button to tune in a station from the Category The CA indicator is displayed in the function mode indication during seek tuning The CAT indicator lights on models without a function mode indication 4 Press the RDM RD button again to cancel Notes When the category selection mode is entered the category of the current or last received channel is displayed first Press the lt 4 or P gt button within 7 seconds after a category has been set to continue seeking channels up or down The category selection mode is canceled and normal reception is resumed if no operation is performed for 7 seconds Presetting a category A category can be preset by registering specific categories in DIRECT buttons 1 to 6 Then the desired category can be recalled by pressing the corresponding DIRECT button 1 Press the RDM RD button to enter the category mode 2 Turn the ROTARY knob clockwise or counterclockwise to select a category 3 Press and hold one DIRECT button for 2 seconds or longer to store the current category in the preset memory Notes e When the name of a channel stored in memory is changed by SIRIUS the display will show the new channel name immediately It will not be removed from the preset channel location e A channel stored in memory may be discontinued at the option of SIRIUS If you attempt to access this channel from the preset location the receiver will give you the
2. Notes e The display shows the abbreviated channel name for 2 seconds when a station is selected before returning to the chosen display mode Scrolling starts when the channel name or other text has been displayed for 2 seconds When scrolling finishes the initial characters appear To start scrolling again press the ADJ button e The ADJ button is described in the source unit instruction manual either as the T TITLE button or A M button This refers to the function of the button labeled ADJ on the source unit panel ADJ or etc Channel selection Channels are selected with the following buttons The lt Q or F gt button Seek Tuning A DIRECT button e The SCN SC button The CAT RDM button For details see the following operation descriptions Notes The audio output is muted and other button operations are not accepted during the channel selection process tuning Seek Tuning 1 Press the lt 4 or I gt button The receiver seeks the next available channel below or above the current channel 2 Press and hold the lt 4 or P gt button for rapid or continuous channel selection The receiver moves to seek channels below or above the current channel If the channel found when either button is released is available that channel is received Otherwise seeking continues until an available channel is found Recalling a preset station A total of 18 SIRIUS stations can
3. SIRIUS SIRIUS Satellite Radio User Manual Thank you for purchasing this product Please read this user s manual in its entirety before operating this equipment After reading this manual be sure to keep it in a handy place e g glove compartment Check the contents of the enclosed warranty card and keep it carefully with this manual Contents FAR a a a AAAA 1 i EC AUTO NS lai i i cssussaccedecsnesesouc EEEO 2 3 INSTALLATION AND WIRING CONNECTIONS o ooccccccccoccnoconcccnconoconccnoconoconccnocono 4 4L SYSTEM EXAMPLES ii E aci n 7 CONTROL aio asno 9 6 SIRIUS OPERATION uusssscssssssscssssssssssssssssessssssssscsssssssssssssssssssscssessesssssscsscsscessssesssceses 11 TES RECIPICATION Sosa li 15 FEATURES 1 m CeNET Connection m RCA Output m Switching for Headunit or Commander operation E Connection of DSC920S Exclusive Commander for operation when using with other line level input devices Single Antenna Terminal 18 Channel presets when used with CeNet devices m CD Changer pass through function 2 PRECAUTIONS Upon initial startup or when starting after turning off the backup power supply the receiver will take longer to play audio and may take up to 30 seconds after reception of the SIRIUS signal before audio is heard Channel names are stored in memory 30 to 60 seconds after start of normal operation If the power is turned off before the text data is written it may not be correctly displayed o
4. INVALID CH or INVLD CH response At that time you may select another station to store in memory Scan function There are two scan modes a category scan mode and a preset scan mode During scanning channels are displayed in abbreviated form and the display mode cannot be switched m Category scanning In a category scan broadcast channels in the same category as the current channel are selected about every 10 seconds 1 Press the SCN SC button to start a category scan 2 Press the SCN SC button a DIRECT button the lt 4 or gt gt button to cancel a category scan Note Category scanning is not available when no category is defined for the current channel m Preset scan A preset scan scans the channels up to 18 channels stored in the preset memory and changes about every 10 seconds 1 Press and hold the SCN SC button for 1 second or longer to start a preset scan 2 Press the SCN SC button a DIRECT button the lt 4 or gt gt button to cancel a preset scan 7 SPECIFICATIONS Receiving Frequencies Satellite 2322 293 2330 207 MHZ _ Terrestrial 2326 250 MHZ Power Power O Power supply Stand alone 4 pin input jack for power and ground mode only _ Power consumption _ Less than 1A A pp Physical Interface Clarion eae units or CD Changers Mode switch Stand alone CeNET mode selectable Mechanical dimension L W H 182 mm 128 mm 29 m
5. US Call Center at 888 539 SIRI and provide the SIRIUS ID and a few other details Verifying your SIRIUS ID 1 Press and hold the ADJ button for 1 second or longer to enter the Adjust mode Note The ADJ button is described in the source unit instruction manual either as the T TITLE button or A M button This refers to the function of the button labeled ADJ on the source unit panel ESN DISP SIRIUS ID 3 Press the I button to display the SIRIUS ID The source unit displays the first 6 digits of the 12 digit SIRIUS ID in the display 4 Turn the ROTARY knob clockwise to change to the last 6 digits of the SIRIUS ID 3 INSTALLATION AND WIRING CONNECTIONS r Before Installation 3 1 Before starting be sure to disconnect the battery s negative terminal to prevent accidents due to short circuits 2 Location Consider safety and operability when selecting a place for installation Avoid the following Locations where the unit will hamper or interfere with driving Locations where the unit could injure passengers if the car stops suddenly Locations exposed to direct sunlight or hot air from the heater etc Locations where the unit may be exposed to rain or water 3 Be sure to use the included screws and brackets Screws other than those supplied could damage the unit 4 When drilling holes to mount the receiver be sure to check beforehand that there are no o
6. be stored 6 SR1 6 SR2 and 6 SR3 This allows you to select your favorite SIRIUS stations and store them in memory for later recall 1 Press the BND button and select the desired SIRIUS band SR1 SR2 or SR3 to store the channel in 2 To recall a stored SIRIUS station press the desired DIRECT button to select that station Storing a preset station 1 Press the BND button and select the desired SIRIUS band SR1 SR2 or SR3 to store the channel in 2 Select the desired station with seek tuning manual tuning or preset tuning 3 Press and hold one of DIRECT buttons for 2 seconds or longer to store the current station into preset memory Notes e When the name of a channel stored in memory is changed by SIRIUS the display will show the new channel name immediately It will not be removed from the preset channel location e A channel stored in memory may be discontinued at the option of SIRIUS If you attempt to access this channel from the preset location the receiver will give you the INVALID CH or INVLD CH response At that time you may select another station to store in memory Category selection function SIRIUS allows you to select broadcast channel by category Receiving stations selected by category 1 Press the RDM RD button to enter the category selection mode 2 Turn the ROTARY knob clockwise or counterclockwise to select a category Or press a DIRECT button if the category is preset
7. bstructions or items on the other side that could be damaged fuel tank wire harnesses or other electronic devices r Accessories D Mounting bracket 2 pieces Canoe clip lt 4 pieces Mounting screw 4 pieces 0 CeNET cable 1 piece Installation Example Installing the unit under the driver s seat 1 Attach the mounting brackets to the sides a of the SIR CL1 using the screws provided Ms 2 Select the location on the floor mat Drill holes in the floor mat to match the positions of the holes in the mounting brackets 3 Insert the canoe clips from the rear of the floor mat and install the SIR CL1 There are three mounting holes on each side of the SIR CL1 Select the appropriate holes to match to the installation location amp amp amp 6 Connection Example and Identification of Parts CeNET input output terminal Connect to the main unit or CD MD changer using the CeNET cable as specified0 2 RCA pin terminals These are used to output audio when the DSC920S sold separately is used to operate the receiver antenna cable 31 ANTENNA terminal E R Connect to the SIRIUS antenna sold separately 4 COMMANDER Controller terminal SIRIUS Connection for DSC920S sold separately SIR CL1 5 COMMANDER Power Supply terminal Used only when operating the SIR CL1 with the E DSC920S sold separately a Bottom v
8. f not Installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to consult the dealer or an experienced radio TV technician for help CAUTION USE OF CONTROLS ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE THE COMPACT DISC PLAYER or COMMANDER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE TECHNICIANS CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER FOR COMPLIANCE COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT INFORMATION FOR USERS CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL SIRIUS What is SIRIUS Satellite Radio Over 100 streams of the best in car entertainment and completely commercial free music Only SIRIUS has 60 original music streams from today s hits to R amp B oldies to classical masterpieces From authentic country and real bluegrass to cool jazz hot latin reggae rock and many more Best of all it s all commercial free a Sirius exclusive Sirius also has over 40 st
9. gt CD mode gt CD changer mode gt etc Selecting a band Press the BND button to select a band Each press of the button changes the display as shown below SR1 gt SR2 gt SR3 gt SR1 The currently received band is displayed in the function mode indication Models without a function mode indication display the band name and channel number in the display m Information displayed during reception The following information is displayed when SIRIUS Satellite Radio cannot be received normally e UPDATING when the receiver is turned on the first time or after a reset Do not turn power off during this time as the receiver is downloading the channel guide e ACQUIRING when there has been a temporary loss of signal and the receiver is attempting to reacquire a signal LINKING is shown on an 8 digit display e INVALID CH a channel without a broadcast has been selected INVLD CH is shown on an 8 digit display e NO SIGN UP a channel not available in your subscription e ANTENNA no antenna is connected or there is a problem with the antenna Switching the display 1 Press the DISP D button to select the desired display The main display or the clock display appears each time you press the DISP D button 2 In the main display press and hold the DISP D button for 1 second or longer to cycle between the following display modes Channel name song title 2 artist name gt category name gt channel name 2
10. iew of the unit 6 CeNET STANDALONE switch p This switch is used to select the operating type CeNET headunit or STAND ALONE DSC920S L ii m py lam How to Connect 1 CeNET Cable Orient the CeNET cable in the direction shown in the figure and insert it until it is locked in position To remove the CeNET cable pull it by lightly grasping the slide cap in your fingers 2 SIRIUS antenna Make sure power is Off Connect a SIRIUS antenna sold separately to the SIRIUS antenna terminal and press until locking tab engages To disconnect make sure power is Off then press the rear of the locking tab to release 4 SYSTEM EXAMPLES E Example 1 SIRIUSH amp SIR CL1 CLARION COMPATIBLE SOUS SATELLITE RADIO RECIEVER D Main unit compatible with CeNET connection CD changer compatible with CeNET connection CeNET cable provided with the SIR CL1 Using this cable connect the SIR CL1 to the main unit CeNET cable provided with the CD changer SIRIUS antenna sold separately 6 Front speakers Rear speakers E Example 2 SIRIUS SIR CL1 Ye oes mite pars D SIRIUS controller DSC920S sold RCA pin audio cable sold separately separately 0 Connection cable provided with the SIRIUS antenna sold separately DSC920S 6 Front speakers G Audio systems with auxiliary or line in connections 9 CONTROLS S
11. m EMC regulation Complies with FCC Part 15 Note e Specifications and design are subject to change without notice for further improvement
12. n the next power up Perform a reset operation if no text data is displayed If the receiver ever stops functioning or appears unresponsive reset it e Resetting Disconnect the SIRIUS Receiver power cable the CeNET cable if connected to the CeNET and the 4 pin power cable during standalone operation wait 10 seconds and connect it again The last channel preset memory and other data stored in the receiver are deleted returning it to its default settings A CeNET and standalone operation switch is provided on the underside of the receiver The switch is set to CeNET position at the time of shipment Do not set this switch to the standalone position when using the CeNET cable headunit operation The receiver becomes warm during operation this is normal and not a cause for concern Do not touch the connector pins on the receiver as this may damage the ICs inside the unit No station is selected when the adj or disp button is pressed quickly after a channel is changed This is because button operations are not accepted until the channel is confirmed It takes between 1 5 to 5 seconds to change channels This equipment has been tested to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and i
13. ource unit buttons example 1 ROTARY Source unit buttons example 2 ROTARY FUNC ADJ DISP Notes m The illustrations show examples of two headunits with button functions m Since this manual covers several models the names of some buttons vary by model As shown below this manual gives different button names when more than one name is used FNC FUNC button SC SCN button etc Display Items Source unit display example 1 Operation status indication 85 SIRIUS indication eae IO A A T Hat A A E ce eee iii ini ii i gt E 88 ji TA f E Fa Ta rr ery iol HAEDO ja oE EEI APA BODA e SA ETa CEJ Ci E Preset channel indication Function mode indication cama Manual indication Source unit display example 2 Operation status indication Preset channel indication MANU Manual indication CEAT Category indication SAT SIRIUS indication 6 SIRIUS OPERATION Selecting SIRIUSSIRIUS SATELLITE RADIO modes Press the SAT button or the FNC FUNC button to select the SIRIUS mode The SIRIUS indication lights up when SIRIUS mode is selected Notes The SAT button selects the SIRIUS mode directly Some head units do not have a SAT button If not press the FNC FUNC button until SIRIUS is selected The FNC FUNC button selects the external devices connected to the source unit in order for example AM FM mode gt DAB mode gt SIRIUS mode
14. reams of world class sports news and entertainment like ESPN NHL NBA MLB CNBC Fox News Radio Disney and E Entertainment Radio With SIRIUS the emphasis is on the music and entertainment you want The music is hosted by Sirius Stream Jockeys who are true experts They back up the music with compelling information about the song being played and they understand that sometimes it s best to just let the music speak for itself Rely on SIRIUS rocket science for superior coverage Only SIRIUS has three powerful satellites that fly directly over the US ensuring coast to coast coverage with high elevation angles This gives the satellites a clear line of sight to your car or home with much less concern for buildings trees or other objects that might block conventional satellite Signals Count on S gt PLEX technology for superior sound resolution SIRIUS employs S gt PLEX technology statistical multiplexing which optimizes the fidelity on each channel to give you superior digital sound So rock really soars jazz really jams and country really sings Once you experience over 100 streams of digital entertainment you ll never want to leave your car For more information visit www sirius com To receive SIRIUS Satellite Radio on this receiver This receiver contains a SIRIUS ID for user identification All you have to do to become a subscriber and enable reception of SIRIUS Satellite Radio is to call the SIRI

SIRIUS Satellite Radio USER MANUAL

Contents

Download Pdf Manuals

Related Search

Related Contents