IDEAL 62-140 TRACETone Tester Instructions Manual
Contents
1. period of 12 months for the test instrument and 3 months for the cables from the date of manufacture or proof of purchase The obligation of IDEAL under this warranty is limited to the repair or replacement at our option during the warranty period of any part that proves to be defective in material or workmanship under normal use installation and service provided the product is returned to IDEAL freight prepaid Products returned to us must be accompanied by a copy of the purchase receipt In the absence of such a receipt the warranty period will cease 12 months from the date of manufacture This warranty does not extend to products that have been subjected to neglect accidental or improper use or to units which have been altered repaired or inspected by anyone other than IDEAL authorized personnel In no event will IDEAL be liable for any incidental or consequential damages Shipping 1 Before returning any product to IDEAL you must first request a Returned Materials Authorization RMA number by contacting our Customer Service Dept at 800 435 0705 No shipments will be accepted without this number which must be clearly marked on the shipping label Ship the equipment with a copy of the sales receipt if available Attach a description of the operational problem Include acontact name address phone number and e mail address if possible Pack securely to prevent damage during shipping Ship prepaid to IDEAL INDUSTRIES IN2. the Amplified Probe to turn on the probe 4 Adjust volume control to a comfortable level If the signal is very loud when near the cable the volume may need to be reduced to keep from overloading the TRACETone When overloaded small increases or decreases in the signal at the tip cannot be heard 5 Hold the tip of the TRACETone near cable to be identified The signal will be loudest on the wire or cable the generator is attached to Separating the wires or cables may help in isolating the correct cable Battery Replacement 1 Remove the screw at the back of the Tone Generator or the Amplified Probe with a 1 Phillips head screwdriver and remove battery door 2 Remove old cell batteries rapping case against the palm of the hand will dislodge batteries 3 Install 4 new LR44 cells being careful to orient plus end of battery with plus symbol on case 4 Replace battery door and reinsert the screw Do not over tighten Product specification Power Requirements 4 x LR44 button cells 6 volts Battery life Generator 100hrs Amplified probe 12hrs Externally applied voltage w o damage 250 volts peak DC or 175 volts RMS AC Tone frequencies 5 995Hz and 845Hz alternating tones Tone voltage 12 volts p p no load new battery Tone power 8dbm into 600 ohms new battery Warranty IDEAL guarantees to the end user purchaser that its products will be free of all defects in material and or workmanship This warranty extends for a
3. C Becker Place Sycamore IL 60178 Dm oO Ww PO Product Registration Please visit www idealindustries com IDEAL INDUSTRIES INC Sycamore IL 60178 U S A 800 435 0705 Customer Assistance www idealindustries com ND 4894 1
4. g lO 62 140 DEAT 7 TRACETone Tone Generator and Amplifier Probe Operating Instructions Conductive probe tip WARNING Do not attach to AC power The TRACETone may be damaged and become a safety hazard for the user CAUTION Improperly crimped damaged or un crimped plugs can damage the jack on the TRACETone Inspect plugs for proper termination and crimping before inserting into the tester Contacts should always be recessed into the plastic grooves of the plug Adjustable volume Tone indication light Amplified Features speaker Tone Generator stores in bottom of Amplified Probe to make carrying easier Three position Two selectable tone styles with easy to read LED on off tone power on indicator switch Built in volume control to meet personal preference Turn on the Amplified Probe by contact and automatic power off mode when Tone Generator is in the stowed mode no dead battery e Accessories to isolate tracing RJ11 Patchcord and Alligator Clip Package Content TRACETone Tone Generator and Amplified Probe test set Alligator Clip with RJ11 interface Satin RU11 patchcord Instructions for Use To Trace a Tone 1 Connect the Tone Generator to the RJ11 Alligator Clip then place the Alligator Clip on the cable to be traced 2 Select one of the tones of choice the green LED will indicate the power on mode 3 Press and hold the black button on
Download Pdf Manuals
Related Search
IDEAL 62 140 TRACETone Tester Instructions Manual