Panasonic WX-RP921 Manual
Contents
1. of diversity recei ver or distributor 6 Screw Adaptor INSTALLATION Mounting the wireless antenna on the Mounting the wireless antenna on the wali with microphone stand mounting bracket 1 Install the WX RP921 on the microphone stand Caution base and turn it to clockwise Do not install the antenna horizontally or up side down Install the wireless antenna at least 1 ft 30 cm below the ceiling 7 1 ft 30 cm or more 1 Mount the mounting bracket provided on the wall with 2 screws or 4 screws 2 Mount the wireless antenna to the mounting brack et and tighten the screw adaptor MOUNTING BRACKET Dimensional Drawing Unit inches mm 9 7 16 240 2 15 16 74 5 053 64 021 2 3 4 70 T N 20 x Ww Lu t wv 1 3 8 35 SPECIFICATIONS Power Source Power Consumption Receiving Frequency Conversion Gain Ripple Output Impedance Antenna Dimensions Excluding Antenna Weight Supptied from Diversity Receivers WX RP8 10 or WX RP820 or Distributor WX RP900 12V DC 6O0mA 797MHz to 803MHzZ 27dB Less than 3dB 75 ohms 1 4 Wavelength Whip Antenna 2 15 16 W X 5 7 8 H X 1 1 4 P 75 W X 150 H X 32 P mm Approx 0 73lbs 330g Dimensions and weight indicated are approximate Specifications are subject to change without notice ACCESSORY Mounting Bracket oos 7 Panasonic Broadcast amp Television Systems2. Company Division of Matsushita Electric Corporation of America RAMSA Professional Audio Systems Executive Office One Panasonic Way Secaucus New Jersey 07094 6550 Katella Ave Cypress CA 90630 714 373 7277 NO693 0 YWA8QA2971AN Printed in Japan ND 22
3. WX RP921 Operatin naructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SER VICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to SA 1965 persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompa nying the appliance SA 1966 WARNING The serial number of this product may be found on the side of the unit You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft Model No Serial No TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE READ THE FOLLOWING CONTENTS INSTRUCTIONS BEFORE USE PR FACE 2 Sin Don nn 4 FEATURES nr enr nn CAUTION PRECAUTIONS canne It is a violation of Federal Law to begin operating this Salem prior tooblaining an FCC Padio License BEFORE INSTALLATION case see nren The FCC ID number for this radio equipment is list
4. ed MAET OPERA ee ene THEIR FUNCTIONS a a dectendivcctacctavetvdebeaxdans ee INSTALLATO N nn mn ms anne FEC i AATA RESEN MOUNTING BRACKET niner SPECIFICATION sosccetisicedes tocvsnavsticonscstadetetteisteteasstaceceeld ACCESSORY a ee nee ar Te rar N et PREFACE The Wireless Antenna WX RP921 is designed to be used with the Diversity Receivers WX RP810 WX RP820 and Distributor WX RP900 It is equipped with a built in down converter from 800MHz to 260MHz to minimize cable loss FEATURES e The WX RP921 includes a pre amp which boosts the antenna signal to compensate for coaxial cable loss between the antennas and diversity receivers WX RP810 WX RP820 It prevents dis ruption of the voice signal due to squelch and a reduction in the signal to noise ratio caused by dead points A phantom power supply system is employed to supply DC power from the Diversity Receivers WX RP810 WX RP820 or Distributor WX RP900 to the Wireless Antenna WX RP921 via a coaxial cable 2 PRECAUTIONS The Wireless Antenna WX RP921 is designed for indoor use Do not install it outdoors Always install the wireless antenna with mounting bracket provided vertically Do not place the receiving antenna in places affected by strong electrical or magnetic fields such as near AC power lines motors transformers Or generators Do not place the wireless antenna near metallic materials as the receiving sensitivity of wireless antenna will be reduced P
5. lace the wireless antennas between 16 7ft 5m and 66ft 20m apart from each other for the best diversity effect Do not place the wireless microphone less than 6 7ft 2m apart from wireless antenna Otherwise interference noise will occur Always use high quality cable Low grade cable will cause signal loss and interference Always install the wireless antenna as a pair BEFORE INSTALLATION The distance between wireless microphone and wireless antenna is changed according to environment of instal lation place Room 98 x 65ft Room 164 x 131f1 View from the ceiling View from the ceiling Approx 65ft Approx 13 tft Wall Wall Antenna B Antenna A Oo O 65ft Max c Wireless Microphone An a B Antenna CPS 65ft Max we my wet Approx 164ft f Approx 82ft at Wiretess Microphone MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS 4 1 Antenna 2 Cover Remove the cover when change the position of Attenuator selection switch 3 Attenuator Selection Switch ATT 0dB 10dB OdB Normally used this position 10dB When the antenna input level is high or interference noise produced set the Attenua tor selection switch to this position 4 Power Indicator POWER Lights in red when the power is supplied from the receiver or distributor 5 Output Connector Connect the coaxial cable between this connector and the antenna input connector
Download Pdf Manuals
Related Search
Panasonic WX RP921 Manual panasonic wr-210a panasonic wireless phones user manuals