Home

YAMAHA SPS-80 SPEAKER STAND set Manual

1. 153 6 900 35 7 16 595 23 7 16 650 25 9 16 When shortened to minimum When extended to maximum Dimensions W x H x D 300 x 650 900 x 300mm Weight 11 13 16 x 25 9 16 35 7 16 x 11 13 16 2 1 kg 4 Ibs 10 oz USABLE SPEAKERS YAMAHA NX 230P the main and rear speakers included in the NS P230 NS P236 speaker package NX 220P the main and rear speakers included in the NS P220 speaker package NX S80S the front and rear speakers included in the AVX S80 sound system NX S60S the front and rear speakers included in the DVX S60 sound system NX S77E the rear speakers included in the AV S77 sound system NX VS10E the rear speakers included in the VS 10 sound system Use a speaker of 1 kg or less Use a speaker with a screw hole of 4 mm in diameter for attaching the speaker mounting bracket E 1 SETUP PROCEDURES Before beginning the setup check the parts list and make sure all the parts are included NAME 3 Remove the speaker mounting bracket from the pole by removing the screw using the screwdriver QUANTITY Pole Speaker 2 p Support mounting bracket Base face screws Diam x Length 4 x 8 mm 2 2 6 Pole Hexagon socket set screws Diam x Length 4 x 6 mm Wrench hexagonal Cable protection seal SA AVI Rubber cap E SETUP
2. PROCEDURES 4 Attach the speaker mounting bracket to the speaker by screwing it into the screw hole on the bottom of the speaker You will need a screwdriver for the setup Attach the support to the base by fastening the three face screws from the holes on the bottom of the base Name plate Speaker not included g 5 Pass the speaker cable through the pole from the Support Do not overtighten the self machine screws Doing end without the cut so may damage the screws or assembly Then pass the cable through the hole on the speaker mounting bracket from the side with the groove as shown in the figure 2 Pass the speaker cable through the support from the bottom A speaker cable more than 4 mm x 2 mm in diameter cannot be used If you use such a cable connect it to the speaker s terminals without passing it through the pole Support Speaker cable not included Zs ack Pole D Speaker mounting bracket 6 Pull out the speaker cable in the length of 15 to 16 cm from the speaker mounting bracket Then attach the speaker mounting bracket to the pole so that the speaker cable fits to the cut in the pole This will lock the speaker cable After that fasten the screw 15 16 cm Screw 7 Insert the pole to the support and adjust the height of the stand After adjusting the height fasten the hexagon socket set screws into the tw
3. SPEAKER STAND YAMAHA Read this before setup SETUP INSTRUCTIONS SPS 80 Thank you for selecting this YAMAHA SPS 80 speaker stand PRECAUTIONS e This speaker stand is only for the speaker systems listed e To prevent the speaker stand from discoloring and in USABLE SPEAKERS below Do not use the speakers other than these listed e To prevent the speaker from falling use the screws and warping keep the speaker stand away from the stoves and places where it will be exposed to direct sunlight etc parts provided with the stand e Do not attempt to clean the speaker stand with chemical e To prevent the speaker stand from falling over select a solvents as this might damage the finish Use a clean location which is flat and stable dry cloth e To avoid accidents resulting from tripping over loose e Secure placement or installation is the owner s speaker cables and to prevent the speaker stand from falling over fix the speaker cables to the wall etc e Do not let the children lean on the stand as this might cause the serious accidents resulting from the falling over of the speaker stand DIMENSIONS SPECIFICATIONS responsibility YAMAHA shall not be liable for any accident caused by improper placement or installation of speakers mm inch Top view 300 11 13 16 Side view 297 11 11 16 47 1 7 8
4. ile pulling out the speaker cable slowly by hand from the base side with the speaker stand laying along protection YAMAHA YAMAHA ELECTRONICS CORPORATION USA 6660 ORANGETHORPE AVE BUENA PARK CALIF 90620 U S A YAMAHA CANADA MUSIC LTD 135 MILNER AVE SCARBOROUGH ONTARIO M1S 3R1 CANADA YAMAHA ELECTRONIK EUROPA G m b H SIEMENSSTR 22 34 25462 RELLINGEN BEI HAMBURG F R OF GERMANY YAMAHA ELECTRONIQUE FRANCE S A RUE AMBROISE CROIZAT BP70 CROISSY BEAUBOURG 77312 MARNE LA VALLEE CEDEX02 FRANCE YAMAHA ELECTRONICS UK LTD YAMAHA HOUSE 200 RICKMANSWORTH ROAD WATFORD HERTS WD1 7JS ENGLAND YAMAHA CORPORATION YAMAHA SCANDINAVIA A B J A WETTERGRENS GATA 1 BOX 30053 400 43 VASTRA FR LUNDA SWEDEN YAMAHA MUSIC AUSTRALIA PTY LTD 17 33 MARKET ST SOUTH MELBOURNE 3205 VIC AUSTRALIA Printed in China e V975830
5. o holes on the support using the longer handle of the included wrench and attach the rubber cap to the support The line on the pole shows the limit of the stand height Do not let the line of the stand height limit go beyond the upper end of the support Otherwise the hexagon socket set screw of the lower side becomes ineffective and the fixation becomes unstable Rubber cap Stand height Hexagon limit socket set screw Support hexagonal The inside of the rubber cap has a space for storing the wrench after the setup 8 Adjust the speaker direction Then put the wrench into the hole of the speaker monting braket and tighten the bracket to the speaker by moving the wrench counterclockwise 9 Connect the speaker cable to the speaker s terminals correctly Refer to the instruction manual of the speakers for connecting the speaker cables 10 Align the speaker cable to the grooved part of the bottom of the base and fix the cable on the base by putting the protection seal on it Cable seal The setup has completed In the same way set up the other stand Make sure to note the following when stretching or shortening the pole after the setup e Make sure to remove the cable protection seal before stretching or shortening the pole e When stretching the pole pull out the pole carefully with the speaker stand laying along e When shortening the pole retract the pole carefully wh

YAMAHA SPS-80 SPEAKER STAND set Manual

Contents

Download Pdf Manuals

Related Search

Related Contents