YAMAHA G1D Manual
Contents
1. Multi pin cable 1 2 Setup e See the G50 owner s manual for G50 setup and operation details e The multi pin cable plug release button must be pressed when unplugging the multi pin cable from the G1D 2 Unplug cable by gripping the puing firmly 3 Turn on the G50 When the G50 power is turned ON the GID power indicator should light indicating that it is receiving power from the G50 4 Play Assuming that your G50 tone generator and other equipment are set up properly refer to the appropriate owner s manuals for details you re now ready to play a Setup 1 3 Specifications E Functions e Volume Control VOL e GUITAR MIX SYNTH Selector e UP DOWN Buttons e Power Indicator e Pickup individual string synthesizer output e Direct Guitar Input Jack e Multi pin Cable Connector individual string synthesizer output direct guitar sound E Package Contents e Pickup amp Controller Unit e Direct guitar cable 1 4 mono phone lt gt mono mini plug e Installing hardware parts E Dimensions wx H xD 85 1mm x 75 9mm x 28 8mm 3 1 3 x 3 x 1 1 8 E Weight 70 g 2 5 oz E 1 4 Specifications YAMAHA YAMAHA CORPORATION M D G EMI Division Yamaha Corporation 1996 VU83880 706POCP5 2 03C0 Printed in Japan2. controller unit aside and carefully drill a 2 millimeter 1 16 inch approx hole at the marked location screw hole E NOTES e For acoustic or semi acoustic guitars or simply if the idea of drilling a hole in your guitar makes you shudder the controller can be attached using only the adhesive tape the Velcro faster or any of the other installation options described below Please note however that screw installation is the most secure method and is recommended wherever possible e The Velcro fastener is provided for players who will be frequently removing and reattaching the G1D DO NOT use the adhesive pads if you use the Velcro fastener Bottom side 3 Attach the controller screw adhesive tape Remove the protective backing from one side of the adhesive tape patches and attach them to the bottom of the controller as shown in the illustra tion E NOTES e You can use the standard adhesive tape or the re usable adhesive pads on just about any type of guitar See The Re usable Adhesive Pads below for details e The adhesive tape pads may react chemically with the finish on some guitars causing discoloration or otherwise marring the finish It might be a good idea to try attaching a small piece of tape pad at some location that is not obvious for a few days before actual installation If your guitar has an arched top or is shaped
3. of each string should be about 1 millimeter 0 04 when each string is fretted at the highest note on the neck The pickup height can be checked by using the supplied clearance gauge Installation 1 1 setup Once installation is complete you re ready to connect and check out your MIDI guitar system assuming you also have a G50 Guitar MIDI Converter and appropriate tone genera tor sound hardware 1 Connect the direct guitar cable Connect the 1 4 mono phone plug end of the direct guitar cable supplied with the G1D to the guitar s output jack and the mono mini plug end of the cable to the G1D direct guitar input jack Direct guitar cable E NOTES e Always connect the direct guitar cable even if you don t intend to use the direct guitar sound The direct guitar cable is essential for proper grounding to minimize noise and prevent electric shock 2 Connect the G1D to the G50 After making sure that the G50 Guitar MIDI Converter power is OFF plug one end of the multi pin cable supplied with the G50 into the GID multi pin connector and the other end into the DIVIDED INPUT connector on the G50 The release button on the multi pin plug should face outward D GUITAR MIDI CONVERTER YAMAHA o cso Multi pin cable E NOTES e For extra security and damage prevention it is a good idea to pass the cable between the strap and guitar body near the body strap pin Strap
4. the bracket can cause the strap pin screw to become loose Suction Cup Installation The supplied suction cups are a handy and fairly secure way to attach the controller unit to guitars with a flat top and a smooth shiny finish To use the suction cups first insert the bases of the three suction cups into the large openings in the three holes on the bottom of the controller unit then slide the bases of the cups toward the narrow section of the holes until they are held securely Then after making sure the surface of your guitar is free from dirt and grease simply press the controller unit onto the guitar top at the appropriate location The suction cups can be removed by slightly lifting the edge of each cup Installing the Pickup Once you ve installed the controller the pickup can be installed using either double sided tape or screws Although the tape is convenient screw installation is recommended because it provides greater security and allows pickup height adjust ment for optimum performance E Hardware The following parts supplied with the G1D are required or optional for installation of the pickup Please make sure you have all the parts Self tapping round head screws 3x25mm 2 SPNgS eier 2 mom e Pickup cushion 1 ra e Pickup spacers A 1MM BERNER 5 ra Re usable double sided adhesive pads 2 E Installation P
5. Converter is plugged in here and the other end of the cable is plugged into the DIVIDED INPUT connector on the G50 The multi pin cable connector delivers both the individual string output from the G1D pickup and the combined output from the guitar s output jack to the G50 Guitar MIDI Converter It also supplies power from the G50 to the GID and sends the control signals produced by the GID UP DOWN buttons and VOL control to the G50 3 Direct Guitar Input Jack This jack receives the combined output from the guitar s normal pickups from the guitar s output jack The short cable supplied with the G1D is used to connect the guitar s output jack large 1 4 phone jack end of the cable to the G1D direct guitar input jack small mini jack end of the cable 4 Power Indicator The G1D is receiving power from the G50 Guitar MIDI Converter when this indicator is lit The indicator lights when the G1D is properly connected to the G50 via the multi pin cable and the G50 power is turned ON 5 Volume Control Controls the volume of the MIDI tone generator s connected to the G50 Guitar MIDI Converter the G50 translates the position of this control to MIDI master volume data which is sent to the tone generator Use the guitar s original volume controls to adjust the volume of the direct guitar sound 6 UP DOWN Buttons These button can be used to select different synthesizer voices and select other functions while playing the GID
6. Press either button briefly to increment or decrement the G50 Guitar MIDI Converter memory number by one and thereby the voice number of the synthesizer or tone generator it is driving or hold either button for continuous scrolling in the corresponding direction 7 GUITAR MIX SYNTH Selector Selects the type of output to be delivered via the multi pin cable connector to the G50 Guitar MIDI Converter as listed below GUITAR Only the direct guitar sound will be heard i e no synthesizer sound will be produced MIX Both the direct guitar sound and individual string synthesizer output will be heard SYNTH Only the individual string synthesizer output is sent to the G50 no direct guitar sound will be heard es Nomenclature 3 Installation Installing the GID on a guitar is not a difficult process but it does require care and at least a modicum of mechanical ability If you don t feel totally confident that you can handle the job it might be a good idea to leave the installation to someone experienced in guitar modification or repair Guitar Compatibility The GID can be installed on most electric and steel string acoustic guitars with the following exceptions e Since the GID employs a magnetic pickup it will not work with nylon or other non metallic strings e The GID is designed for use with 6 string guitars It will not work properly with 12 string guitars or other non standar
7. YAMAHA DIVIDED PICKUP UNIT Owner s Manual Bedienungsanleitung Mode d emploi The GID is a high performance guitar synthesizer pickup driver designed for use with the Yamaha G50 Guitar MIDI Converter When properly installed and adjusted it can add high performance MIDI guitar synthesizer capability to just about any electric or steel string acoustic guitar Please read this owner s manual carefully and follow the installation instructions within in order to ensure proper operation Contents Precautions E location Do not expose the GID to the following conditions to avoid deformation discoloration or more serious damage 2 Direct sunlight e g near a window High temperatures e g near a heat source outside or in a car during the daytime Excessive humidity Excessive dust Strong vibration Connections When connecting the G1D to the Yamaha G50 Guitar MIDI Converter be sure to use the specified multi pin cable supplied with the G50 Guitar MIDI Converter Always connect the direct guitar cable page 12 even if you don t intend to use the direct guitar sound The direct guitar cable is essential for proper grounding to minimize noise and prevent electric shock Always unplug cables by gripping the plug firmly not by pulling on the cable Disconnect all cables before moving the instrument or any connected equipment PLEASE READ THIS BEFORE PROCEEDING Handling and Transport Neve
8. ble sided tape from the existing spacer then attach the new spacer to the top of the existing spacer after removing its backing e When removing a spacer to lower the pickup be sure to remove both the spacer and its backing tape Finally attach fresh double sided tape to the bottom of the pickup remove the backing care fully attach the pickup to the uppermost spacer then re string and tune the guitar E Installation Procedure Screw Screw installation has several advantages over tape installation screw installation is more secure the height of the pickup can be more precisely adjusted and pickup height can be easily re adjusted as required without having to remove and reattach double sided tape E NOTES e Screw installation requires at least a 13 millimeter 1 2 space between the guitar top and strings e Adjust the pickup height using spacers no springs if the distance between guitar top and strings is less than 13 mm 1 Mark the optimum position for installation The pickup should be located between the bridge pickup and bridge see NOTES below The cable end of the pickup should be oriented toward the sixth string low E One pair of the pickup s magnetic yokes should be under each string String spacing varies somewhat on different guitars and the pickup will function properly as long as each string passes over part of the corre sponding yokes not necessarily the exact center Bridge p
9. d and string height are adjusted properly then tune the strings to their normal pitch Adjust the height of the pickup using the appropriate spacer or combination of spacers see NOTES below so that the dis tance between the top of the pickup and the bottom of each string is about 1 millimeter 0 04 when each string is fretted at the highest note on the neck The pickup height can be checked by using the supplied clearance gauge The distance between the pickup and the bottom of the strings can be set less than 1 mm as long as the strings do not touch the pickup when fretted at the highest note on the neck 1 millimeter 0 04 an Bridge pickup Pickup Bridge Guitar body Clearance gauge 20 millimeter 3 4 1 millimeter 0 04 F E NOTES e Don t remove the backing from the pickup cushion or spacers when initially setting up the pickup height Please note that the cushion spacer backing adds about 0 1 millimeter 0 004 to their thickness so take this added thickness into account when using a number of spacers To compensate for differences in height between the first and sixth strings e g if your guitar has an arched top use an appropriate number of one quarter or one third width spacers under the lower end of the pickup the spacers can be cut easily with a good pair of scissors Cut Double sided adhesive tape Cut spacers 3 Attach the pickup Remove the stri
10. d dirt they can be restored to virtually like new conditions by washing carefully with a neutral detergent If you do repeatedly attach and remove the re usable adhesive pads it is a good idea to replace the original protective backing when the pads are not in use to keep them in top condition Bracket Installation This installation option has the advantages that no holes need to be drilled in the guitar To use the bracket first unscrew the two screws marked with arrows on the bottom of the controller unit then use the same screws to attach the controller unit to the bracket as shown in the illustration Next attach the spacers double sided adhesive to the bracket to protect the guitar surface from the screw heads and attach the bracket to the guitar in the appropriate position as shown in the illustra tion Spacer Double sided adhesive tape An alternative method is to attach the bracket using the guitar s strap pin the spacers should still be used to prevent the controller bracket assembly from scratching the surface of the guitar Loosen the strap pin on the guitar body by unscrewing its attachment screw by a few turns slide the slot in the bracket under the pin as shown in the illustra tion then tighten the pin screw until the bracket is held firmly in position E CAUTION e Repeated loosening and tightening of the strap pin or application of excessive force to
11. d string configura tions e The GID pickup should be installed between the guitar s bridge and bridge pickup Installa tion may not be possible if there is not enough room between the bridge and bridge pickup of your guitar or between the guitar top and strings IMPORTANT Make sure your guitar s neck truss rod and string height intonation bridge are properly adjusted before installing the G1D Installing the Controller Unit Install the controller unit before installing the pickup being careful not to damage the pickup during the installation process A number of installation options are provided e Screw e Double sided adhesive tape Re usable adhesive pads e Velcro fastener e Bracket e Suction cups Choose the method which best is best suited to your guitar and playing requirements 4 Installation E Hardware The following parts are provided for installation of the controller unit Please make sure you have all the parts e Self tapping round head screw 3x16mm e Re usable double sided adhesive pads transparent 3 7 e Spacer double sided adhesive 6 e Velcro fastener cece ee eeese access eeeees 1 Bracket r nee 1 SUCTION CUPS nnennnnneensnnnnnnnnnnnnnnnnnnnnnnnnn 3 E Installation Procedure 1 Determine the optimum location for installation Normally the controller should be attached somewhere behind the g
12. ickup Bridge U UT UCU No more than Pickup 20 millimeters 3 4 OK OK NG String Pickup s magnetic yokes 1 0 Installation E NOTES e The pickup should be located as far as possible but no more than 20 millimeters 3 4 from the bridge e Make sure the pickup does not interfere with the operation of a tremolo arm or other guitar controls Once the pickup has been positioned correctly carefully mark the centers of the two screw holes at either end of the pickup on the guitar body using a fine pen or scribe 2 Drill the screw holes Remove the strings from the guitar and very carefully drill 2 millimeter 0 08 approx holes at the marked locations The holes may have to be slightly larger in diameter if your guitar s body is made from a very hard wood such as maple cherry or rosewood 3 Attach the pickup Insert the two self tapping round head screws 3x25mm through the screw holes in the pickup and place the springs over the screw shafts extend ing below the pickup Screw the screws in the corresponding holes in the guitar top E CAUTION e Be careful not to damage the pickup cable when installing the pickup 4 Re string and adjust the pickup height Re string and tune the guitar then carefully adjust the pickup height by loosening or tightening the pickup screws The distance between the top of the pickup and the bottom
13. in such a way that the controller won t sit properly with only the standard adhesive tape use as many of the spacers as required in the appropriate location s to position the controller as required The spacers are adhesive on both sides with protective backing like the standard adhesive tape Next carefully clean the area on the guitar body to which the controller is to be attached to eliminate dust dirt and particularly any oil or grease which might prevent the adhesive from sticking Then remove the protective backing from the exposed side of the adhesive tape and carefully attach the control ler to the guitar making sure that the screw hole in the controller is perfectly aligned with the screw hole in the body of your guitar if you drilled one Press firmly but don t use excessive force to ensure that the tape sticks securely Finally screw the supplied self tapping round head screw 3 x 16 mm into the pre drilled hole in the guitar body through the hole in the controller Screw only finger tight if you attempt to screw the screw in too far or too tight you might damage the controller and or your guitar 6 Installation The Re usable Adhesive Pads The re usable adhesive pads can be used in the same way as the standard double sided adhesive tape for controller unit installation They can be re used many times and if their adhesive qualities deteriorate due to accumulated dust an
14. ngs from the guitar Apply the double sided tape to the bottom of the pickup and remove the backing Remove the backing from the required pickup cushion spacers and carefully attach them to the bottom of the pickup Finally carefully attach the pickup spacer assembly to the guitar at the marked position then re string and tune the guitar Pickup Cut Double sided adhesive tape Spacers A B Cushion E NOTES e The re usable double sided adhesive pads page 8 can be used in place of the bottom layer of adhesive tape guitar side Cut the pads to match the shape of the pickup as required 4 Check the height Check the pickup height again and play the guitar in all ranges to ensure that the strings do not come in contact with the pickup If all is well then the installation is complete Installation 9 If you need to readjust the pickup height If the pickup height needs to be re adjusted remove the strings and carefully pry the pickup from the guitar by sliding a thin flat object e g a small knife blade under the sixth string end of the pickup between the pickup and top spacer and gently lifting the pickup away from the spacer The double sided tape can then be rolled off the bottom of the pickup as shown in the illustra tion Readjust the height as required by adding or removing spacers e To add a new spacer in order to raise the pickup remove any used dou
15. r apply excessive force to the controls connectors or other parts of the instrument Physical shocks caused by dropping bumping or placing heavy objects on the instrument can result in scratches and more serious damage Be careful not to damage the G1D controller when placing the guitar in a case or on a stand Cleaning Clean the unit with a dry soft cloth A slightly damp cloth may be used to remove stubborn grime and dirt Never use cleaners such as alcohol or thinner Service and Modification The G1D contains no user serviceable parts Opening it or tampering with it in any way can lead to irreparable damage and possibly electric shock Refer all servicing to qualified YAMAHA personnel YAMAHA is not responsible for damage caused by improper installation handling or operation Precautions Nomenclature 1D YAMAHA DOWN VOL 7 4 up 5 1 Pickup This is the actual pickup unit which converts the physical motion of the guitar s strings into an electrical signal which can be processed by the GID and transmitted to the G50 Guitar MIDI Converter E CAUTION e Because of its slender dimensions the pickup unit is quite delicate and can be damaged if sub jected to unnecessary force bending or twisting Handle the pickup carefully 2 Multi pin Cable Connector This is the main output from the G1D One end of the multi pin cable supplied with the G50 Guitar MIDI
16. rocedure Tape 1 Mark the optimum position for installation The pickup should be located between the bridge pickup and bridge ideally 20 mm from the bridge If the ideal 20 mm placement is not possible the pickup should be located as far as possible but no more than 20 millimeters away from the bridge The cable end of the pickup should be oriented toward the sixth string low E One pair of the pickup s magnetic yokes should be under each string String spacing varies somewhat on different guitars and the pickup will function properly as long as each string passes over part of the corresponding yokes not necessarily the exact center Check that the strings pass over the yokes even when bending the strings Bridge pickup Bridge UOUUUU UT No more than Pickup 20 millimeters 3 4 OK OK NG String Pickup s magnetic yokes E NOTES e Make sure the pickup does not interfere with the operation of a tremolo arm or other guitar controls e If the bridge side pickup of your guitar is a hm bucking type attach the divided pickup to the bridge side pickup See above illustration Once the pickup has been positioned correctly carefully mark the position on the guitar body Small pieces of marking tape can be used if you don t want to mark directly on the guitar body 8 Installation 2 Set the pickup height First make sure the truss ro
17. uitar s bridge as shown in the illustration It should be accessible but it should not interfere with your playing or any of the guitars controls or adjustments Consider the following points carefully when deciding on the best location to install the controller Controller Pickup Direct guitar s cable Multi pin cable The controller and pickup cable should not get in the way of your picking hand at any time Make sure the location you choose will not affect your playing style The controller should not block or hamper access to any of the guitar s controls tone volume bridge adjustments especially watch out for intonation saddle screws accessed from the rear of the bridge The controller must be well within reach of both the pickup cable when the pickup is in its final installed position and the direct guitar cable Neither the controller unit itself nor any of the connected cable plugs should extend beyond the body of the guitar to prevent accidental damage Installation 5 2 Mark and drill the controller screw hole see NOTES below E CAUTION e Make sure the multi pin cable and direct guitar s cable are disconnected from the controller before While holding the controller unit in exactly the position it is to be installed use a fine pen or scribe to mark the center of the screw hole located in the multi pin cable recess of the controller on the body of your guitar Then set the
Download Pdf Manuals
Related Search
YAMAHA G1D Manual