YAMAHA NS-100 Speaker System user manual
Contents
1. 70 mm 8 3 x 16 4 x 10 6 ATE a EEEE A AEA 8 6 kg 19 0 Ibs Note When the cover is removed take care not to touch the speaker units with your hands or to exert excessive force with tools e Specifications subject to change without notice due to product improvements e Care should be taken not to exceed the input power values noted above CONNECTIONS TO YOUR AMPLIFIER This speaker system is capable of standard connections and bi wiring connections Before making connections make sure that the amplifier is switched off lt Standard Connections gt Leave the short bars in place when connecting Speakers output terminals of the amplifier Amplifier or Receiver E Connections e Connect the screw type input terminals at the rear of the speakers to the speaker output terminals of your amplifier with the speaker cables e Connect the terminals on both the amplifier and the speakers using one side of the cable Connect the terminals on both components using the other side of the cable e Connect one speaker to the left marked L terminals of your amplifier and another speaker to the right marked R terminals making sure not to reverse the polarity If one speaker is connected with reversed polarity the sound will be unnatural and lack bass Procedure Loosen the terminal knob Remove approx 10 mm 3 8 insulation from the speaker cable and insert the ba2. English YAMAHA N OWNER S MANUAL S 100 Speaker System Thank you for selecting this YAMAHA NS 100 speaker system PRECAUTIONS Read these precautions carefully before using your speaker e Any time you note distortion reduce the volume control on your amplifier to a lower setting Never allow your amplifier to be driven into clipping Otherwise the speaker may be damaged e When using an amplifier with a rated output power higher than the nominal input power of the speaker care should be taken never to exceed the speaker s maximum input e Do not attempt to clean the speaker with chemical solvents as this might damage the finish To clean wipe with a dry soft cloth e To prevent the enclosure from warping or discoloring do not place the speaker where it will be exposed to direct sunlight or excessive humidity e Do not place the speaker where it is liable to be knocked over or struck by falling objects Stable placement will also ensure better sound performance e Placing the speakers on the same shelf or rack as the turntable can result in feedback e Secure placement or installation is the owner s responsibility YAMAHA shall not be liable for any accident caused by improper placement or installation of the speaker PLACING THE SPEAKERS Place the speakers on a sturdy vibration free surface on a well built stand E Using as 2ch stereo speakers Better stereo im
3. ages will be obtained when the speakers are slightly angled in towards the listeners E Using as main speakers in a multi channel system Position the speakers on both sides of the TV The positioning of speakers is important because it controls the whole sound quality of a multi channel system Set up the speakers on the basis of your listening position by following the owner s manual supplied with your amplifier REMOVING THE FRONT COVER SPECIFICATIONS The front cover is fastened to the enclosure at four points and can TY PGi ai ene 2 way 2 speaker bass reflex speaker system be removed if desired To remove the cover hold on to both sides Magnetically shielded type and slowly pull straight away from the speaker To reattach line up Speaker Unit ne neinei 16 cm 6 5 cone woofer the four pegs on the inside surface of the cover with the four 3 cm 1 dome tweeter corresponding holes on the speaker and push gently Nominal Impedance eesccceeseeeeeeeeeeeneeeeeeeeeeeneeeeeenneeeneaes 6 ohms Frequency Response ceseseeeerteeeeeeeeeenaeeeeeneees 38 Hz 35 kHz Nominal Input POWE ccceeeeeeeseeeeeneeeeeeeeeeeneeeeenaeeeseneees 100 W Maximum Input POWE eeeceeesseeeeereeeesneeeeenaeeeennaeeeeneeeee 300 W Sensit a eea EE E E a aaas 90 dB 2 83 V m Crossover Frequency cceccecesesecceceeeeeeeeeeeeaeeeeeesneeeaeenee 3 kHz Dimensions WXHXD eeeeneeeeerrnnn 212 x 416 x 2
4. re wire end properly into the terminal hole Tighten the knob Test the security of the connection by tugging lightly on the cable at the terminal Note Do not let the bare speaker wires touch each other as this could damage the speaker and or the amplifier lt Bi Wiring Connections gt Remove the short bars before connecting Tweeter terminals Amplifier or Receiver Amplifier or Receiver Both SPEAKERS A and B should be selected Bi Wiring Connections This speaker system is capable of bi wiring connections To connect the speakers to the output terminals of the amplifier two pairs of cables for each of woofer and tweeter are used instead of standard connections This type of connection decreases the modulation distortion caused by electric resistance of the cables and driving current of the speakers Consequently purer sound quality can be expected To utilize bi wiring connections remove the short bars from the terminals first and then connect the woofer and tweeter to the amplifier separately using two pairs of cables Note For bi wiring connections use the same type of cable for both the woofer and tweeter making sure to match the polarity YAMAHA CORPORATION Printed in Malaysia C V404280
Download Pdf Manuals
Related Search
YAMAHA NS 100 Speaker System user manual ns speaker yamaha manual yamaha ns 1000 speakers ns speaker yamaha setup yamaha ns-100 yamaha ns 1000 speakers review yamaha ns-1000m speakers yamaha ns 1000 speakers for sale yamaha ns 1000m speakers for sale yamaha ns 1 speakers ns speaker yamaha specs yamaha ns 200m speakers yamaha ns-100x yamaha ns-100m yamaha ns 1000 specs yamaha ns 2000 speakers yamaha ns 200 speakers review yamaha ns 500 speakers ns-1000 yamaha yamaha ns 1000 review yamaha ns 2000a speaker reviews yamaha ns 150 speakers yamaha ns 2000 speaker reviews