Home

ASRock Wolfdale1333-DVI User Manual

1. Parallel Port Address Use this item to set the address for the onboard parallel port or disable it Configuration options Disabled 378 and 278 Parallel Port Mode Use this item to set the operation mode of the parallel port The default value is ECP EPP If this option is set to ECP EPP it will show the EPP version in the following item EPP Version Configuration options Normal Bi Directional and ECP EPP EPP Version Use this item to set the EPP version Configuration options 1 9 and 1 7 ECP Mode DMA Channel Use this item to set the ECP mode DMA channel Configuration options DMAO DMA1 and DMA3 Parallel Port IRQ Use this item to set the IRQ for the parallel port Configuration options IRQ5 and IRQ7 3 3 8 USB Configuration BIOS SETUP UTILITY Advanced USB Configuration To enable or disable the onboard USB controllers USB 2 0 Support Enabled Legacy USB Support Disabled Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2005 American Megatrends Inc USB Controller Use this item to enable or disable the use of USB controller USB 2 0 Support Use this item to enable or disable the USB 2 0 support Legacy USB Support Use this item to enable or disable the support to emulate legacy I O devices such as mouse keyboard etc Or you may select Auto so that the system will start to auto detect i
2. Use this item to specify the system time System Date Day Month Date Year Use this item to specify the system date 3 3 Advanced Screen In this section you may set the configurations for the following items CPU Configuration Chipset Configuration ACPI Configuration IDE Configuration PCIPnP Configuration Floppy Configuration SuperlO Configuration and USB Configuration 28 BIOS SETUP UTILITY Advanced H W Monitor Security Advanced Settings Configure CPU WARNING Setting wrong values in below sections may cause system to malfunction gt Chipset Configuration gt ACPI Configuration gt IDE Configuration gt PCIPnP Configuration p Floppy Configuration gt SuperIO Configuration gt USB Configuration Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2005 American Megatrends Inc Setting wrong values in this section may cause 4 the system to malfunction 3 3 1 CPU Configuration BIOS SETUP UTILITY Advanced CPU Configuration Select the over clock DEE mode CPU Frequency MHz 133 PCIE Frequency MHz Did Boot Failure Guard Enabled Spread Spectrum Auto Ratio Actual Value 9 Enhance Halt State Disabled Max CPUID Value Limit Disabled Select Screen Intel R Virtualization tech Enabled Select Item CPU Thermal Throttling Enabled Change Option No Excute Memory Protection Disabled General Help H
3. see p 10 No 17 412V match the black wire to the CHA_FAN_SPEED g ground pin CPU Fan Connector eg Please connect a CPU fan cable 4 pin CPU FAN1 to this connector and match Q Q e e see p 10 No 4 EE the black wire to the ground pin Cru FAN SPEED FAN SPEED CONTROL 23 24 4 Though this motherboard provides 4 Pin CPU fan Quiet Fan support the 3 Pin CPU fan still can work successfully even without the fan speed control function If you plan to connect the 3 Pin CPU fan to the CPU fan connector on this motherboard please connect it to Pin 1 3 Pin 1 3 Connected 3 Pin Fan Installation ATX Power Connector Please connect an ATX power 24 3 n 24 pin ATXPWR1 supply to this connector see p 10 No 26 12 1 Though this motherboard provides 24 pin ATX power connector it can still work if you adopt a traditional 20 pin ATX power supply To use the 20 pin ATX power supply please plug your power supply along with Pin 1 and Pin 13 24 13 i 20 Pin ATX Power Supply Installation 4 12 1 ATX 12V Connector Please note that it is necessary 4 pin ATX12V1 to connect a power supply with see p 10 No 2 ATX 12V plug to this connector so that it can provides sufficient power Failing to do so will cause the failure to power up 2 10 SATAII Hard Disk Setup Guide Before installing SATAII hard disk to your computer please carefully read below SATAII hard disk setup guide Some default setting of SATAII hard
4. 0 header USB4_5 is shared with USB ports 23 on the I O panel When using the front panel USB ports by attaching the front panel USB cable to USB4_5 header the USB ports 23 on the I O panel will not be able to function WiFi Header USB 5V_2 i NC 11 pin WIFI NE enpi see p 10 No 20 ss o G 1 Oo da END PMEH DO USB 5V_1 This header supports WiFi AP function with ASRock WiFi 802 11g WiFi 802 11n module an easy to use wireless local area network WLAN adapter It allows you to create a wireless environmentand enjoy the convenience of wireless network connectivity DeskExpress Hot Plug Detection TX S Header Le tplugs 5 pin IR1 1 see p 10 No 3 w This header supports the Hot Plug detection function for ASRock DeskExpress Internal Audio Connector 4 pin CD1 Eri CD1 This connector allows you to receive stereo audio input CD1 see p 10 No 23 2990 from sound sources such as 500 a CD ROM DVD ROM TV tuner card or MPEG card Front Panel Audio Header END This is an interface for front PRESENCE A 9 pin HD_AUDIO1 MERT panel audio cable that allows UT RET see p 10 No 22 4 convenient connection and 1 H control of audio devices our J_SENSE OUT2_R MIC2_R MIC2_L 4 1 High Definition Audio supports Jack Sensing but the panel wire on the chassis must support HDA to function correctly Please follow the instruction i
5. 2 9 Onboard Headers and Connectors 2 10 SATAII Hard Disk Setup Guide onrrnvrnrnvrrrrnrvrrnervernnenr 2 11 Serial ATA SATA Serial ATAII SATAII Hard Disks Installation vu fin tai ont eee ade 2 13 Untied Overclocking Technology 3 BIOS SETUP UTILITY 3 1 Introduction EEN 3 1 2 Navigation Keys rrrrnnrnnrnvvrnrnrnnrnrrnvnvrnnnnrnnrnrrenennn 3 2 Main SCr en ss sieste mia ah tit A 3 3 1 CPU Configuration arrrronrrnnnrvrnnnrrnrnrrnnenvnnrnnnnennn 3 3 2 Chipset Configuration 3 3 3 ACPI Configuration 3 3 4 IDE Configuration asrvnnnnrnnnnvrnnnnrnnrnrrnnrnrnnrnrnnennn 3 3 5 PCIPnP Configuration 3 3 6 Floppy Configuration 3 3 7 Super IO Configuration 3 3 8 USB Configuration arrrnonrrnnnvrrnnnrrnrnrrnnrnnnnrnnnnrnnn 3 4 Hardware Health Event Monitoring Screen 3 5 Boot SCreOM ij ee Eege 3 5 1 Boot Settings Configuration arrrrrnrrnnrnrnnrnrnnennr 3 60 Security SCOM aasan aaea Aaaa a EE EAEE SARETE Ai 32 EXUSCeen EE 4 Software Support 44 4 1 Install Operating System 44 4 2 Support CD Information cccceeeeeeeeee
6. ASRock Wolfdale1333 DVI Support CD One 80 conductor Ultra ATA 66 100 IDE Ribbon Cable One Ribbon Cable for a 3 5 in Floppy Drive One Serial ATA SATA Data Cable Optional One Serial ATA SATA HDD Power Cable Optional One ASRock 6CH I O Plus I O Shield One DVI Graphics SI Card 1 2 Specifications Platform Micro ATX Form Factor 9 6 in x 8 7 in 24 4 cm x 22 1 cm CPU LGA 775 for Intel Dual Core Core 2 Extreme Core 2 Dua I Pentium Dual Core Celeron supporting Dual Core Wolfdale processors Compatible with all FSB1333 1066 800 533MHz CPUs except Quad Core see CAUTION 1 Supports Hyper Threading Technology see CAUTION 2 Supports Untied Overclocking Technology see CAUTION 3 Supports EM64T CPU Chipset Northbridge Intel 945GC A2 Southbridge Intel ICH7 Memory Dual Channel DDRII Memory Technology see CAUTION 4 2x DDRII DIMM slots Support DDRII667 533 see CAUTION 5 Max capacity 4GB see CAUTION 6 Hybrid Booster CPU Frequency Stepless Control see CAUTION 7 ASRock U COP see CAUTION 8 Boot Failure Guard B F G Expansion Slot 1 x PCI Express x16 slot 1x PCI Express x1 slot 2 x PCI slots Graphics Intel Graphics Media Accelerator 950 Pixel Shader 2 0 DirectX 9 0 Max shared memory 224MB see CAUTION 9 Dual VGA Output support D Sub and DVI D ports with DVI Graphics SI card by independent display cont
7. SRock Wolfdale1333 DV1 User Manual Version 1 1 Published December 2007 Copyright 2007 ASRock INC All rights reserved Copyright Notice No part of this manual may be reproduced transcribed transmitted or translated in any language in any form or by any means except duplication of documentation by the purchaser for backup purpose without written consent of ASRock Inc Products and corporate names appearing in this manual may or may not be regis tered trademarks or copyrights of their respective companies and are used only for identification or explanation and to the owners benefit without intent to infringe Disclaimer Specifications and information contained in this manual are furnished for informa tional use only and subject to change without notice and should not be constructed as a commitment by ASRock ASRock assumes no responsibility for any errors or omissions that may appear in this manual With respect to the contents of this manual ASRock does not provide warranty of any kind either expressed or implied including but not limited to the implied warran ties or conditions of merchantability or fitness for a particular purpose In no event shall ASRock its directors officers employees or agents be liable for any indirect special incidental or consequential damages including damages for loss of profits loss of business loss of data interruption of business and the like even if ASRock has been advised o
8. Serial ATAII SATAII hard disks You may install SATA SATAII hard disks on this motherboard for internal storage devices This section will guide you to install the SATA SATAII hard disks STEP 1 Install the SATA SATAII hard disks into the drive bays of your chassis STEP2 Connect the SATA power cable to the SATA SATAII hard disk STEP3 Connect one end of the SATA data cable to the motherboard s SATAII connector STEP 4 Connect the other end of the SATA data cable to the SATA SATAII hard disk 2 12 Driver Installation Guide To install the drivers to your system please insert the support CD to your optical drive first Then the drivers compatible to your system can be auto detected and listed on the support CD driver page Please follow the order from up to bottom side to install those required drivers Therefore the drivers you install can work properly 2 13 Untied Overclocking Technology This motherboard supports Untied Overclocking Technology which means during overclocking FSB enjoys better margin due to fixed PCI PCIE buses Before you enable Untied Overclocking function please enter Overclock Mode option of BIOS setup to set the selection from Auto to CPU PCIE Async Therefore CPU FSB is untied during overclocking but PCI PCIE buses are in the fixed mode so that FSB can operate under a more stable overclocking environment p Please refer to the warning on page 7 for the possible overclocking ris
9. Step 1 2 Rotate the load lever to fully open po sition at approximately 135 degrees Step 1 3 Rotate the load plate to fully open po sition at approximately 100 degrees Step 2 Insert the 775 LAND CPU Step 2 1 Hold the CPU by the edges where are marked with black lines au xoe1q au 9e1q Step 2 2 Orient the CPU with IHS Integrated Heat Sink up Locate Pin1 and the two orientation key notches Pin1 r F alignment ke alignment key orientation He 9 Ni key notch key notch i j 775 Pin Socket 775 LAND CPU 13 14 d Step 3 Step 4 For proper inserting please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket Step 2 3 Carefully place the CPU into the socket by using a purely vertical motion Step 2 4 Verify that the CPU is within the socket and properly mated to the orient keys Remove PnP Cap Pick and Place Cap Use your left hand index finger and thumb to support the load plate edge engage PnP cap with right hand thumb and peel the cap from the socket while pressing on center of PnP cap to assist in removal 1 It is recommended to use the cap tab to handle and avoid kicking off the PnP cap 2 This cap must be placed if returning the motherboard for after service Close the socket Step 4 1 Rotate the load plate onto the IHS Step 4 2 While pressing down lightly on load plate engage the load
10. lever Step 4 3 Secure load lever with load plate tab under retention tab of load lever 2 4 Installation of CPU Fan and Heatsink This motherboard is equipped with 775 Pin socket that supports Intel 775 LAND CPU Please adopt the type of heatsink and cooling fan compliant with Intel 775 LAND CPU to dissipate heat Before you installed the heatsink you need to spray thermal interface material between the CPU and the heatsink to improve heat dissipation Ensure that the CPU and the heatsink are securely fastened and in good contact with each other Then connect the CPU fan to the CPU FAN connector CPU FAN1 see page 10 No 4 For proper installation please kindly refer to the instruction manuals of your CPU fan and heatsink Below is an example to illustrate the installation of the heatsink for 775 LAND CPU Step 1 Apply thermal interface material onto center of IHS on the socket surface Step 2 Place the heatsink onto the socket Ensure fan cables are oriented on side closest to the CPU fan connector on the motherboard CPU FAN1 see page 10 No 4 elt Step 3 Align fasteners with the motherboard Be throughholes Step 4 Rotate the fastener clockwise then press down on fastener caps with thumb to install and lock Repeat with remaining fasteners If you press down the fasteners without rotating them clockwise the heatsink cannot be secured on the motherboard Step 5 Connect fan header with the CPU fan c
11. network WLAN adapter It allows you to create a wireless environment and enjoy the convenience of wireless network connectivity Please visit our website for the availability of ASRock WiFi 802 11g WiFi 802 11n module ASRock website http www asrock com 1 3 Motherboard Layout so 2 34 5 6 7 22 1cm 8 7 in S gt 7 L g is fem 295 SES d SES E ozga a S i O E 3 P 2 a E 2 a R q a gt We uss20 z z TUSBO ez ig z B USB1 Super Lo g ZS Intel 2 z E sascca2 85 E 26 ewei P Chipset Gs 5 a 8 PCIE1 25 PCI E EXPRESS PCIE2 9 Intel 10 PCI ICH7 11 RoHS sms 12 Pci2 SATAII sms 13 le venu un fer Cl P we 3 20 19 PS2_USB_PWR1 Jumper ATX 12V Connector ATX12V1 DeskExpress Hot Plug Detection Header IR1 CPU Fan Connector CPU_FAN1 775 Pin CPU Socket North Bridge Controller 2 x 240 pin DDRII DIMM Slots Dual Channel DDRII_1 DDRII 2 Yellow IDE1 Connector IDE1 Blue Clear CMOS Jumper CLRCMOS1 South Bridge Contr
12. out the following message Dis card changes Select OK to discard all changes Load Optimal Defaults When you select this option it will pop out the following message Load optimal defaults Select OK to load the default values for all the setup configurations 43 44 Chapter 4 Software Support 4 1 Install Operating System This motherboard supports various Microsoft Windows operating systems 2000 XP XP 64 bit Vista Vista 64 bit Because motherboard settings and hardware options vary use the setup procedures in this chapter for general reference only Refer to your OS documentation for more information 4 2 Support CD Information The Support CD that came with the motherboard contains necessary drivers and useful utilities that enhance the motherboard features 4 2 1 Running The Support CD To begin using the support CD insert the CD into your CD ROM drive The CD automatically displays the Main Menu if AUTORUN is enabled in your computer If the Main Menu did not appear automatically locate and double click on the file ASSETUP EXE from the BIN folder in the Support CD to display the menus 4 2 2 Drivers Menu The Drivers Menu shows the available devices drivers if the system detects installed devices Please install the necessary drivers to activate the devices 4 2 3 Utilities Menu The Utilities Menu shows the applications software that the motherboard supports Click on a specific item
13. 6 Expansion Slots PCI and PCI Express Slots There are 2 PCI slots and 2 PCI Express slots on this motherboard PCI slots PCI slots are used to install expansion cards that have the 32 bit PCI interface PCIE slots PCIE1 PCIE x16 slot is used for PCI Express cards with x16 lane width graphics cards or ASRock DVI Graphics Sl card PCIE2 PCIE x1 slot is used for PCI Express cards with x1 lane width cards such as Gigabit LAN card SATA2 card etc 1 If you install the add on PCI Express VGA card to PCIE1 PCIE x16 slot 4 the onboard VGA will be disabled If you install the add on PCI Express VGA card to PCIE1 PCIE x16 slot and adjust the Internal Graphics Mode Select BIOS option to Enabled the onboard VGA will be enabled and the primary screen will be onboard VGA 2 You can only choose either PCI Express VGA card or DVI Graphics Sl card to install to PCIE 1 PCIE x16 slot Installing an expansion card Step 1 Before installing the expansion card please make sure that the power supply is switched off or the power cord is unplugged Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation Step 2 Remove the bracket facing the slot that you intend to use Keep the screws for later use Step 3 Align the card connector with the slot and press firmly until the card is completely seated on the slot Step 4 Fasten the card to the chassis with scr
14. 64 bit Vista Vista 64 bit compliant Certifications FCC CE WHQL WARNING Please realize that there is a certain risk involved with overclocking including adjusting the setting in the BIOS applying Untied Overclocking Technology or using the third party overclocking tools Overclocking may affect your system stability or even cause damage to the components and devices of your system It should be done at your own risk and expense We are not responsible for possible damage caused by overclocking CAUTION 1 FSB1333 CPU will operate in overclocking mode Under this situation PCIE frequency will also be overclocked to 115MHz 2 About the setting of Hyper Threading Technology please check page 30 3 This motherboard supports Untied Overclocking Technology Please read Untied Overclocking Technology on page 26 for details 4 This motherboard supports Dual Channel Memory Technology Before you implement Dual Channel Memory Technology make sure to read the installation guide of memory modules on page 16 for proper installation 5 Please check the table below for the CPU FSB frequency and its corre sponding memory support frequency CPU FSB Frequency Memory Support Frequency 1333 DDRII533 DDRII667 1066 DDRII533 DDRII667 800 DDRII400 DDRII533 DDRII667 533 DDRII400 DDRII533 When you use a FSB1333 CPU on this motherboard it will run at DDRII500 if y
15. CI Devices Power On Disabled PS 2 Keyboard Power On Disabled RTC Alarm Power On Disabled ACPI HPET Table Disabled Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2005 American Megatrends Inc Suspend to RAM This field allows you to select whether to auto detect or disable the Suspend to RAM feature Select Auto will enable this feature if the system supports it Restore on AC Power Loss This allows you to set the power state after an unexpected AC Power loss If Power Off is selected the AC Power remains off when the power recovers If Power On is selected the AC Power resumes and the system starts to boot up when the power recovers Ring In Power On Use this item to enable or disable Ring In signals to turn on the system from the power soft off mode PCI Devices Power On Use this item to enable or disable PCI devices to turn on the system from the power soft off mode PS 2 Keyboard Power On Use this item to enable or disable PS 2 keyboard to turn on the system from the power soft off mode RTC Alarm Power On Use this item to enable or disable RTC Real Time Clock to power on the system ACPI HPET Table Use this item to enable or disable ACPI HPET Table The default value is Disabled Please set this option to Enabled if you plan to use this motherboard to submit Windows Vista certification 3 3 4 IDE Configuration BIOS SETUP UTILIT
16. Change Option OnBoard HD Audio Auto General Help Front Panel Auto Load Defaults OnBoard Lan Enabled Save and Exit Exit PCI Fix Function Enabled v02 54 C Copyright 1985 2005 American Megatrends DRAM Frequency If Auto is selected the motherboard will detect the memory module s inserted and assigns appropriate frequency automatically You may also select other value as operating frequency 200MHz DDRII 400 266 MHz DDRII 533 333MHz DDRII 667 The configuration options may change according to the corresponding FSB frequency of the CPU you adopt Flexibility Option The default value of this option is Disabled It will allow better tolerance for memory compatibility when it is set to Enabled 81 32 DRAM CAS Latency Use this item to adjust the means of memory accessing Configuration options are 6 5 4 3 and Auto DRAM RASt to CAS Delay This controls the latency between the DRAM active command and the read write command Configuration options 2 DRAM Clocks 3 DRAM Clocks 4 DRAM Clocks 5 DRAM Clocks 6 DRAM Clocks and Auto DRAM RAS Precharge This controls the idle clocks after a precharge command is issued Configuration options 2 DRAM Clocks 3 DRAM Clocks 4 DRAM Clocks 5 DRAM Clocks 6 DRAM Clocks and Auto DRAM RAS Activate to Precharge Thhis controls the number of DRAM clocks for TRAS Configuration options 4 DRAM Clocks 5 DRAM Cloc
17. MB if necessary This item will not be used under Windows Vista OS because the driver will intelligently detect physical memory available and allocate necessary video memory DVMTIFIXED Memory You are allowed to adjust the shared memory size in this item if you set DVMT Mode Select as DVMT Mode Configuration options 64 MB 128MB and Maximum DVMT OnBoard HD Audio Select Auto Enabled or Disabled for the onboard HD Audio feature If you select Auto the onboard HD Audio will be disabled when PCI Sound Card is plugged Front Panel Select Auto Enabled or Disabled for the onboard HD Audio Front Panel OnBoard Lan This allows you to enable or disable the OnBoard Lan feature PCI Fix Function This allows you to enable or disable PCI Fix Function The default value is Enabled If this item is set to Enabled PCI frequency can be fixed at 33 3 MHz If this item is set to Disabled PCI clock can be synchronized to PCIE clock DRAM Voltage Use this to select DRAM Voltage Configuration options High Middle Low and Auto The default value of this feature is Auto VTT Voltage Use this to select DRAM Voltage Configuration options High Low and Auto The default value is Auto 33 34 3 3 3 ACPI Configuration BIOS SETUP UTILITY Advanced ACPI Configuration Select auto detect or EEE disable the STR feature Restore on AC Power Loss Power Off Ring In Power On Disabled P
18. Y Advanced d Set Compatible IDE Configuration tarer OG MS DOS Win NT deviceis used PSATAII 1 Hard Disk Set Enhanced PSATAII 2 Not Detected when Native OS SATAII 3 Not Detected CWin2000 XP pSATAII 4 Not Detected is used IDE1 Master ATAPI CDROM IDE1 Slave Not Detected Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2005 American Megatrends Inc ATAIIDE Configuration Please select Compatible when you install legacy OS Windows NT If native OS Windows 2000 XP is installed please select Enhanced When Compatible is selected Combined Option It allows you to select between SATA 1 SATA 2 SATA 3 SATA 4 SATA 1 SATA 3 IDE 1 and IDE 1 SATA 2 SATA 4 If it is set to SATA 1 SATA 3 IDE 1 then SATAII 2 SATAII_4 will not work Likewise if it is set to IDE 1 SATA 2 SATA 4 then SATAII 1 SATAII 3 will not work Because Intel ICH7 south bridge only supports four IDE devices 4 under legacy OS Windows NT you have to choose SATA 1 SATA 2 SATA 3 SATA 4 SATA 1 SATA 3 IDE 1 or IDE 1 SATA 2 SATA 4 when the installed device is used with legacy OS SATA 1 SATA 2 SATA 1 SATA 3 IDE 1 SATA 2 SATA 3 SATA 4 IDE 1 SATA 4 Master SATAII 1 SATAII 2 SATAII 1 SATAII 2 Slave SATAII 3 SATAII 4 SATAII 3 SATAII 4 IDE Device Configuration You may set the IDE c
19. an start to use DVI D output function with this motherboard 19 20 2 8 Jumpers Setup The illustration shows how jumpers are setup When the jumper cap is placed on pins the jumper is Short If no jumper cap 4 I is placed on pins the jumper is Open The illustration shows a 3 pin jumper whose pin1 LET D s G and pin2 are Short when jumper cap is Short Open placed on these 2 pins Jumper Setting Description PS2 USB PWR1 Short pin2 pin3 to enable 12 23 see p 10 No 1 DR Be el 5VSB standby for PS 2 5V 5VSB or USB wake up events Note To select 5VSB it requires 2 Amp and higher standby current provided by power supply Clear CMOS CLRCMOS1 2 pin jumper see p 10 No 9 2 pin jumper Note CLRCMOS1 allows you to clear the data in CMOS The data in CMOS includes system setup information such as system password date time and system setup parameters To clear and reset the system parameters to default setup please turn off the computer and unplug the power cord from the power supply After waiting for 15 seconds use a jumper cap to short 2 pins on CLRCMOS1 for 5 seconds 2 9 Onboard Headers and Connectors 4 Onboard headers and connectors are NOT jumpers Do NOT place jumper caps over these headers and connectors Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard FDD connector 33 pin FLOPPY1 see p 10 No 19 the red s
20. disks may not be at SATAII mode which operate with the best performance In order to enable SATAII function please follow the below instruction with different vendors to correctly adjust your SATAII hard disk to SATAII mode in advance otherwise your SATAII hard disk may fail to run at SATAII mode Western Digital 715 3 1 S IC 2210000 If pin 5 and pin 6 are shorted SATA 1 5Gb s will be enabled On the other hand if you want to enable SATAII 3 0Gb s please remove the jumpers from pin 5 and pin 6 SAMSUNG 7151311 Il 8l lal2 I If pin 3 and pin 4 are shorted SATA 1 5Gb s will be enabled On the other hand if you want to enable SATAII 3 0Gb s please remove the jumpers from pin 3 and pin 4 HITACHI Please use the Feature Tool a DOS bootable tool for changing various ATA features Please visit HITACHI s website for details http www hitachigst com hdd support download htm 4 The above examples are just for your reference For different SATAII hard disk products of different vendors the jumper pin setting methods may not be the same Please visit the vendors website for the updates 25 26 2 11 Serial ATA SATA Serial ATAII SATAII Hard Disks Installation This motherboard adopts Intel ICH7 south bridge chipset that supports Serial ATA SATA
21. eeeeeeeeeeeeeeees 44 4 2 1 Running Support CD o oo eee eeeeeeeeee 44 4 2 2 Drivers Meng 0 tege SEENEN 44 4 2 3 Utilities Menu 44 4 2 4 Contact Information 44 Chapter 1 Introduction Thank you for purchasing ASRock Wolfdale1333 DVI motherboard a reliable motherboard produced under ASRock s consistently stringent quality control It delivers excellent performance with robust design conforming to ASRock s commitment to quality and endurance In this manual chapter 1 and 2 contain introduction of the motherboard and step by step guide to the hardware installation Chapter 3 and 4 contain the configuration guide to BIOS setup and information of the Support CD Because the motherboard specifications and the BIOS software might be 4 updated the content of this manual will be subject to change without notice In case any modifications of this manual occur the updated version will be available on ASRock website without further notice You may find the latest VGA cards and CPU support lists on ASRock website as well ASRock website http www asrock com If you require technical support related to this motherboard please visit our website for specific information about the model you are using www asrock com support index asp 1 1 Package Contents ASRock Wolfdale1333 DVI Motherboard Micro ATX Form Factor 9 6 in x 8 7 in 24 4 cm x 22 1 cm ASRock Wolfdale1333 DVI Quick Installation Guide
22. en the screws Doing so may damage the motherboard 2 2 Pre installation Precautions Take note of the following precautions before you install motherboard components or change any motherboard settings 1 Unplug the power cord from the wall socket before touching any component 2 To avoid damaging the motherboard components due to static electricity NEVER place your motherboard directly on the carpet or the like Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components 3 Hold components by the edges and do not touch the ICs 4 Whenever you uninstall any component place it on a grounded antistatic pad or in the bag that comes with the component 4 Before you install or remove any component ensure that the power is switched off or the power cord is detached from the power supply Failure to do so may cause severe damage to the motherboard peripherals and or components 2 3 CPU Installation For the installation of Intel 775 LAND CPU please follow the steps below 775 Pin Socket Overview the CPU surface is unclean or if there is any bent pin on the socket Do not force to insert the CPU into the socket if above situation is found Otherwise the CPU will be seriously damaged f Before you insert the 775 LAND CPU into the socket please check if Step 1 Open the socket Step 1 1 Disengaging the lever by depressing down and out on the hook to clear retention tab
23. ews 17 18 2 7 DVI Graphics SI Card Installation Guide With the onboard VGA D Sub output and the external installation of our DVI Graphics SI card this motherboard provides users with dual VGA output support DVI D and D Sub You can easily enjoy the benefits of dual VGA output support by connecting the D Sub monitor to the VGA D Sub port on the I O panel and connecting the DVI D monitor to our DVI Graphics SI card inserted to PCIE1 PCIE x16 slot on this motherboard Please refer to below procedures for proper installation of DVI Graphics SI card Step 1 Install the DVI Graphics SI card to PCIE 1 PCIE x16 slot Please refer to the expansion card installation procedures on page 17 for details d DVI Graphics st_ RoHS FC 5 DVI Graphics SI card Step 2 Connect the DVI D monitor to the DVI D output connector of DVI Graphics Sl card which is inserted to PCIE1 PCIE x16 slot on this motherboard DVI D connector of DVI D monitor DVI D output connector of DVI Graphics SI card Step 3 Connect the D Sub monitor to the VGA D Sub port on the I O panel of this motherboard Step 4 If you have installed Intel VGA driver from our support CD to your system already you can freely enjoy the benefits of DVI D output function with this motherboard after your system boots If you haven t installed Intel VGA driver yet please install Intel VGA driver from our support CD to your system and restart your computer Then you c
24. f the possibility of such damages arising from any defect or error in the manual or product FG This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CALIFORNIA USA ONLY The Lithium battery adopted on this motherboard contains Perchlorate a toxic substance controlled in Perchlorate Best Management Practices BMP regulations passed by the California Legislature When you discard the Lithium battery in California USA please follow the related regulations in advance Perchlorate Material special handling may apply see www dtsc ca gov hazardouswaste perchlorate ASRock Website http www asrock com Contents TIntr duetonssaknksusaat anive taket 1 1 Package Contents AA 1 2 Specifications 1 3 Motherboard Layout 1 4 ASRock 6CH I O PIUS raira arona 2 ALAS CLOW HE eegene ere 2 2 Pre installation Precautions ccccceceeeeeeeeteeeteees 2 3 CPU Installation 2 4 Installation of Heatsink and CPU fan 2 5 Installation of Memory Modules DIMM 2 6 Expansion Slots PCI and PCI Express Slots oonrn000se 2 7 DVI Graphics SI Card Installation Guide 2 8 Jumpers Setup onei tient ieee
25. f there is no USB device connected Auto option will disable the legacy USB support 3 4 Hardware Health Event Monitoring Screen In this section it allows you to monitor the status of the hardware on your system including the parameters of the CPU temperature motherboard temperature CPU fan speed chassis fan speed and the critical voltage BIOS SETUP UTILITY Main Advanced H W Monitor Security ten Target Fan Speed Hardware Health Event Monitoring Fast CPU Temperature 37C 98F Middle M B Temperature 31 C 8TF Slow CPU Fan Speed 3400 RPM Chassis Fan Speed N A Vcore 1 629V 3 30V 3 306V 5 00V 5 067V Select Screen 12 00V 11 890V Select Item General Help CPU Quiet Fan Enabled Load Defaults Target CPU Temperature SE 50 Save and Exit Tolerance C 02 Exit v02 54 C Copyright 1985 2005 American Megatrends Inc CPU Quiet Fan This item allows you to identify the temperature of CPU fan If you set this option as Disabled the CPU fan will operate in full speed If you set this option as Enabled you will find the items Target CPU Temperature OCT Tolerance C and Minimun Fan Speed appear to allow you adjusting them The default value is Disabled You are allowed to enable this function only when you install 4 pin CPU fan Target CPU Temperature C The target temperature will be between 45 C and 65 C The default value is 50 Tolerance C T
26. he default value of tolerance is 2 which means the error of the target CPU temperature will be within ae Target Fan Speed Use this option to set the target fan speed You can freely adjust the target fan speed according to the target CPU temperature that you choose The default value is Fast Configuration options Fast Middle and Slow 40 3 5 Boot Screen In this section it will display the available devices on your system for you to config ure the boot settings and the boot priority BIOS SETUP UTILITY Main Advanced H W Monitor Security Exit BootiSettings Configure Settings during System Boot 1st Boot Device Ist Floppy Device 2nd Boot Device HDD PM HDS722580VL 3rd Boot Device CD DVD 3S CD ROM C 4th Boot Device USB gt Hard Disk Drives p Removable Drives gt CD DVD Drives Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2005 American Megatrends Inc 3 5 1 Boot Settings Configuration BIOS SETUP UTILITY Boot Settings Configuration To enable or disahie the boot from onboard LAN feature Bootup Num Lock Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2005 American Megatrends Inc Boot From Onboard LAN Use this item to enable or disable the Boot From Onboard LAN feature Boot Up Num Lock If this item is set to On
27. indows XP Set to Enabled if using Microsoft Windows XP or Linux kernel version 2 4 18 or higher This option will be hidden if the installed CPU does not support Hyper Threading technology Intel R SpeedStep tm tech Chipset Configuration Intel R SpeedStep tm tech is Intels new power saving technology Processor can switch between multiple frequency and voltage points to enable power savings The default value is Auto Configuration options Auto Enabled and Disabled If you install Windows XP and select Auto you need to set the Power Schemes as Portable Laptop to en able this function If you install Windows Vista and want to enable this function please set this item to Enabled This item will be hidden if the current CPU does not support Intel R SpeedStep tm tech Please note that enabling this function may reduce CPU voltage and lead to system stability or compatibility issue with some power supplies Please set this item to Disable if above issue occurs 3 3 2 Chipset Configuration BIOS SETUP UTILITY Advanced SE Auto Flexibility Option Disabled S DRAM CAS Latency Auto He MORO DRAM RAS to CASH Delay Auto dc Geer DRAM RAS Precharge Auto SEDER K W DRAM RAS Activate to Precharge Auto Primary Graphics Adapter PCI Internal Graphics Mode Select Auto DVMT Mode Select DVMT Mode DVMT FIXED Memory Maximum DVMT Select Screen Select Item
28. it will automatically activate the Numeric Lock function after boot up 41 42 3 6 Security Screen In this section you may set or change the supervisor user password for the system For the user password you may also clear it BIOS SETUP UTILITY Advanced H W Monitor Boot Security Security Settings Install or Change the password Supervisor Password Not Installed User Password Not Installed Change User Password Select Screen Select Item Change General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2005 American Megatrends Inc 3 7 Exit Screen BIOS SETUP UTILITY Main Advanced H W Monitro Boot Security Exit Options Exit system setup after saving the changes Discard Changes and Exit Discard Changes F10 key can be used for this operation Load Optimal Defaults Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2005 American Megatrends Inc Save Changes and Exit When you select this option it will pop out the following message Save configuration changes and exit setup Select OK to save the changes and exit the BIOS SETUP UTILITY Discard Changes and Exit When you select this option it will pop out the following message Dis card changes and exit setup Select OK to exit the BIOS SETUP UTILITY without saving any changes Discard Changes When you select this option it will pop
29. k before you apply Untied Overclocking Technology Chapter 3 BIOS SETUP UTILITY 3 1 Introduction This section explains how to use the BIOS SETUP UTILITY to configure your system The BIOS FWH chip on the motherboard stores the BIOS SETUP UTILITY You may run the BIOS SETUP UTILITY when you start up the computer Please press lt F2 gt during the Power On Self Test POST to enter the BIOS SETUP UTILITY otherwise POST will continue with its test routines If you wish to enter the BIOS SETUP UTILITY after POST restart the system by pressing lt Ctl gt lt Alt gt lt Delete gt or by pressing the reset button on the system chassis You may also restart by turning the system off and then back on Because the BIOS software is constantly being updated the 4 following BIOS setup screens and descriptions are for refer ence purpose only and they may not exactly match what you see on your screen 3 1 1 BIOS Menu Bar The top of the screen has a menu bar with the following selections Main To set up the system time date information Advanced To set up the advanced BIOG features PCIPnP To set up the PCI features Boot To set up the default system device to locate and load the Operating System Security To set up the security features Chipset To set up the chipset features Exit To exit the current screen or the BIOS SETUP UTILITY Use lt lt gt key or lt gt key to choose among the selections on the menu bar and then
30. ks 6 DRAM Clocks 7 DRAM Clocks 8 DRAM Clocks 9 DRAM Clocks 10 DRAM Clocks 11 DRAM Clocks 12 DRAM Clocks 13 DRAM Clocks 14 DRAM Clocks 15 DRAM Clocks and Auto Primary Graphics Adapter This item shows the primary graphics adapter The default value is PCI Configuration options Onboard PCI and PCI Express Internal Graphics Mode Select If you select Auto the onboard VGA will be automatically disabled when you install VGA card the onboard VGA will be enabled without the installa tion of any add on VGA card If you select Enabled 8MB or Enabled 1MB the onboard VGA will be enabled DVMT Mode Select Use this option to adjust DVMT mode Configuration options Fixed Mode DVMT Mode and Fixed DVMT Mode The default value is DVMT Mode DVMT Dynamic Video Memory Technology is an architecture that offers breakthrough performance for the motherboard through efficient memory utilization In Fixed mode a fixed size fragment of the system memory is allocated to the graphics core In DVMT mode the graphics driver allocates memory as needed for running graphics applications and is cooperatively using this memory with other system components In Fixed DVMT mode the graphics processor gets a fixed size chunk of 64MB of memory and up to 64MB of dynamically allotted memory This mode guarantees that at least 64MB of memory is available to the graphics core with a possibility to increase this amount to 128
31. n our manual and chassis manual to install your system 2 If you use AC 97 audio panel please install it to the front panel audio header as below A Connect Mic IN MIC to MIC2 L B Connect Audio R RIN to OUT2 Rand Audio L LIN to OUT2 L C Connect Ground GND to Ground GND D MIC RET and OUT RET are for HD audio panel only You don t need to connect them for AC 97 audio panel E Enter BIOS Setup Utility Enter Advanced Settings and then select Chipset Configuration Set the Front Panel Control option from Auto to Enabled Enter Windows system Click the icon on the lower right hand taskbar to enter Realtek HD Audio Manager For Windows 2000 XP XP 64 bit OS Click Audio 1 0 select Connector Settings ee choose Ed Disable front panel jack detection and save the change by clicking OK For Windows Vista Vista 64 bit OS Click the right top Folder icon vat Choose Disable front panel jack detection and save the change by clicking OK System Panel Header ED This header accommodates 9 pin PANEL1 Ten several system front panel see p 10 No 14 functions 1 IDummy RESET GND HDLED 8 Chassis Speaker Header Joooo Please connect the chassis T 4 pin SPEAKER 1 bul speaker to this header see p 10 No 16 ey MY Chassis Fan Connector Please connect a chassis fan 3 pin CHA FAN1 cable to this connector and GND
32. oller Primary SATAII Connector SATAII_1 Red Third SATAII Connector SATAII 3 Orange 14 System Panel Header PANEL1 15 Secondary SATAII Connector SATAII 2 Red 16 Chassis Speaker Header SPEAKER 1 17 Chassis Fan Connector CHA FAN1 18 BIOS SPI Chip 19 Floppy Connector FLOPPY1 20 WiFi Header WIFI 21 PCI Slots PCI1 2 22 Front Panel Audio Header HD AUDIO1 23 Alnternal Audio Connector CD1 Black 24 PCI Express x1 Slot PCIE2 25 PCI Express x16 Slot PCIE1 26 ATX Power Connector ATXPWR1 Fourth SATAII Connector SATAII 4 Orange 27 Shared USB 2 0 Header USB2 3 Blue 1 4 ASRock 6CH I O Plus 1 PS 2 Mouse Port Green 7 Microphone Pink 2 Parallel Port 8 Shared USB 2 0 Ports USB45 3 USB 2 0 Ports USB23 9 USB 2 0 Ports USB01 4 RJ 45 Port 10 VGA Port 5 Line In Light Blue 11 COM Port 6 Line Out Lime 12 PS 2 Keyboard Port Purple 11 12 Chapter 2 Installation Wolfdale1333 DVI is a Micro ATX form factor 9 6 x 8 7 24 4 x 22 1 cm motherboard Before you install the motherboard study the configuration of your chassis to ensure that the motherboard fits into it 4 Make sure to unplug the power cord before installing or removing the motherboard Failure to do so may cause physical injuries to you and damages to motherboard components 2 1 Screw Holes Place screws into the holes indicated by circles to secure the motherboard to the chassis 4 Do not over tight
33. onfiguration for the device that you specify We will use the Primary IDE Master as the example in the following instruction 35 36 Advanced BIOS SETUP UTILITY Primary IDE Master Device Vendor Size LBA Mode Block Mode PIO Mode Asyne DMA Ultra DMA S M A R T LBA Large Mode Block Multi Sector Transfer PIO Mode DMA Mode S M A R T 32Bit Data Transfer Hard Disk ST340014A 40 0 GB Supported 16Sectors 14 MultiWord DMA 2 Ultra DMA 5 Supported Auto Auto Auto Auto Disabled Enabled Select the type of device connected to the system Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2005 American Megatrends Inc TYPE Use this item to configure the type of the IDE device that you specify Configuration options Not Installed Auto CD DVD and ARMD Not Installed Select Not Installed to disable the use of IDE device Auto Select Auto to automatically detect the hard disk drive After selecting the hard disk information into BIOS use a disk utility such as FDISK to partition and format the new IDE hard disk drives This is necessary so that you can write or read data from the hard disk Make sure to set the partition of the Primary IDE hard disk drives to active CD DVD This is used for IDE CD DVD drives ARMD This is used for IDE ARMD ATAPI Removable Media Device s
34. onnector on the motherboard Step 6 Secure excess cable with tie wrap to ensure cable does not interfere with fan operation or contact other components 15 2 5 Installation of Memory Modules DIMM Wolfdale1333 DVI motherboard provides two 240 pin DDRII Double Data Rate DIMM slots and supports Dual Channel Memory Technology For dual channel configuration you always need to install two identical the same brand speed size and chip type memory modules in the DDRII DIMM slots to activate Dual Channel Memory Technology Otherwise it will operate at single channel mode 1 Itis not allowed to install a DDR memory module into DDRII slot otherwise this motherboard and DIMM may be damaged 2 If you install only one memory module or two non identical memory modules it is unable to activate the Dual Channel Memory Technology Installing a DIMM Please make sure to disconnect power supply before adding or removing DIMMs or the system components Step 1 Unlock a DIMM slot by pressing the retaining clips outward Step 2 Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation 4 The DIMM only fits in one correct orientation It will cause permanent Step 3 Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated 2
35. ou adopt a DDRII533 memory module 6 Due to the chipset limitation the actual memory size may be less than 4GB for the reservation for system usage under Windows XP Windows XP 64 bit Windows Vista and Windows Vista 64 bit 7 Although this motherboard offers stepless control it is not recom mended to perform over clocking Frequencies other than the recom mended CPU bus frequencies may cause the instability of the system or damage the CPU 8 While CPU overheat is detected the system will automatically shutdown Before you resume the system please check if the CPU fan on the motherboard functions properly and unplug the power cord then plug it back again To improve heat dissipation remember to spray thermal grease between the CPU and the heatsink when you install the PC system 9 The maximum shared memory size is defined by the chipset vendor and is subject to change Please check Intel website for the latest information 10 Before installing SATAII hard disk to SATAII connector please read the SATAII Hard Disk Setup Guide on page 25 to adjust your SATAII hard disk drive to SATAII mode You can also connect SATA hard disk to SATAII connector directly 11 Power Management for USB 2 0 works fine under Microsoft Windows Vista 64 bit Vista XP 64 bit XP SP1 or SP2 2000 SP4 12 WiFi header supports WiFi AP function with ASRock WiFi 802 11g WiFi 802 11n module an easy to use wireless local area
36. press lt Enter gt to get into the sub screen 27 3 1 2 Navigation Keys Please check the following table for the function description of each navigation key Navigation Key s Function Description be Des Moves cursor left or right to select Screens UT Moves cursor up or down to select items 1 To change option for the selected items lt Enter gt To bring up the selected screen lt F1 gt To display the General Help Screen lt F9 gt To load optimal default values for all the settings lt F10 gt To save changes and exit the BIOS SETUP UTILITY lt ESC gt To jump to the Exit Screen or exit the current screen 3 2 Main Screen When you enter the BIOS SETUP UTILITY the Main screen will appear and display the system overview BIOS SETUP UTILITY Advanced H W Monitor Security System Overview Use Enter TAB or SHIFT TAB to K 200203 select a field System Date Wed 10 24 2007 BIOS Version Wolfdale1333 DVI P1 00 Use or to Processor Type Intel R CPU 3 40 GHz configure system Time 64bit Processor Speed 3400 MHz Microcode Update F34 17 Cache Size 1024KB Select Screen Select Item Total Memory 512MB with 8MB shared memory 3 Change Field Dual Channel Memory Mode Select Field DDRIII 256MB 266MHz DDRII533 General Help DDRII2 256MB 266MHz DDRII533 Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2005 American Megatrends Inc System Time Hour Minute Second
37. requires no hardware support from the chipset In the C1 power state the processor maintains the context of the system caches Max CPUID Value Limit For Prescott CPU only some OSes ex NT4 0 cannot handle the function with disable This should be enabled in order to boot legacy OSes that cannot support CPUs with extended CPUID functions Intel R Virtualization tech When this option is set to Enabled a VMM Virtual Machine Architecture can utilize the additional hardware capabilities provided by Vanderpool Technology This option will be hidden if the installed CPU does not support Intel R Virtualization Technology CPU Thermal Throttling You may select Enabled to enable P4 CPU internal thermal control mecha nism to keep the CPU from overheated This option will be hidden if the current CPU does not support CPU Thermal Throttling No Excute Memory Protection No Execution NX Memory Protection Technology is an enhancement to the IA 32 Intel Architecture An IA 32 processor with No Execute NX Memory Protection can prevent data pages from being used by malicious software to execute code This option will be hidden if the current CPU does not support No Excute Memory Protection Hyper Threading Technology To enable this feature it requires a computer system with an Intel Pentium 4 processor that supports Hyper Threading technology and an operating system that includes optimization for this technology such as Microsoft W
38. rollers Audio 5 1 CH High Definition Audio Realtek ALC660VD Audio Codec LAN Realtek PCIE x1 LAN 8101E Speed 10 100 Ethernet Supports Wake On LAN Rear Panel I O ASRock 6CH I O Plus 1 x PS 2 Mouse Port 1 x PS 2 Keyboard Port 1 x Serial Port COM1 1 x VGA Port 1 x Parallel Port ECP EPP Support 6 x Ready to Use USB 2 0 Ports 1 x RJ 45 LAN Port HD Audio Jack Line in Front Speaker Microphone Connector 4 x SATAII 3 0 Gb s connectors No Support for RAID and Hot Plug functions see CAUTION 10 1 x ATA100 IDE connector supports 2 x IDE devices 1 x Floppy connector 1 x DeskExpress Hot Plug Detection header CPU Chassis FAN connector 24 pin ATX power connector 4 pin 12V power connector CD in header Front panel audio connector 1 x USB 2 0 header supports 2 USB 2 0 ports shared with USB23 ports on the I O panel see CAUTION 11 1 x WiFi header see CAUTION 12 BIOS Feature 4Mb AMI BIOS AMI Legal BIOS Supports Plug and Play ACPI 1 1 Compliance Wake Up Events Supports jumperfree AMBIOS 2 3 1 Support Support CD Drivers Utilities AntiVirus Software Trial Version Hardware CPU Temperature Sensing Monitor Chassis Temperature Sensing CPU Fan Tachometer Chassis Fan Tachometer CPU Quiet Fan Voltage Monitoring 12V 5V 3 3V Vcore os Microsoft Windows 2000 XP XP
39. sable the PCI IDE BusMaster feature 37 38 3 3 6 Floppy Configuration In this section you may configure the type of your floppy drive BIOS SETUP UTILITY Advanced Floppy Configuration Select the type of floppy drive connected to the system Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2005 American Megatrends Inc 3 3 7 Super IO Configuration BIOS SETUP UTILITY Advanced Configure Super IO Chipset Allow BIOS to Enable o or Disable Floppy Controller Serial Port Address 3F8 IRQ4 Infrared Port Address Disabled Parallel Port Address 378 Parallel Port Mode ECP EPP EPP Version ECP Mode DMA Channel Parallel Port IRQ Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2005 American Megatrends Inc OnBoard Floppy Controller Use this item to enable or disable floppy drive controller Serial Port Address Use this item to set the address for the onboard serial port or disable it Configuration options Disabled 3F8 IRQ4 2F8 IRQ3 3E8 IRQ4 DES IRQ3 Infrared Port Address Use this item to set the address for the onboard infrared port or disable it Configuration options Disabled 2F8 IRQ3 and 2E8 IRQ3 If you plan to use ASRock DeskExpress on this motherboard please keep this item on Disabled option
40. then follow the installation wizard to install it 4 2 4 Contact Information If you need to contact ASRock or want to know more about ASRock welcome to visit ASRock s website at http www asrock com or you may contact your dealer for further information
41. triped side to Pin1 Note Make sure the red striped side of the cable is plugged into Pin1 side of the connector Primary IDE connector Blue 39 pin IDE1 see p 10 No 8 connect the blue end 4 N connect the black end to the motherboard C am to the IDE devices 80 conductor ATA 66 100 cable Note Please refer to the instruction of your IDE device vendor for the details Serial ATAII Connectors These Serial ATAII SATAII SATAII 1 see p 10 No 11 connectors support SATAII or SATA hard disk for internal SATAII 2 see p 10 No 15 SATAII 3 see p 10 No 12 SATAII 1 SATAII 4 storage devices The current SATAII 4 see p 10 No 13 SATAII interface allows up to SATAIL 2 3 0 Gb s data transfer rate Serial ATA SATA Either end of the SATA data cable Data Cable can be connected to the SATA Optional SATAII hard disk or the SATAII connector on the motherboard Serial ATA SATA Please connect the black end of Power Cable SATA power cable to the power Optional t connector on each drive Then connec p t connect the white end of SATA BECH power cable to the power powersupply connector of the power supply 21 22 Shared USB 2 0 Header 9 pin USB4 5 see p 10 No 27 USB PWR p 3 P 3 GND Besides six default USB 2 0 ports on the I O panel there is one USB 2 0 header on this motherboard This USB 2 0 header can support two USB 2 0 ports The shared USB 2
42. uch as MO LBA Large Mode Use this item to select the LBA Large mode for a hard disk gt 512 MB under DOS and Windows for Netware and UNIX user select Disabled to disable the LBA Large mode Block Multi Sector Transfer The default value of this item is Auto If this feature is enabled it will enhance hard disk performance by reading or writing more data during each transfer PIO Mode Use this item to set the PIO mode to enhance hard disk performance by optimizing the hard disk timing DMA Mode DMA capability allows the improved transfer speed and data integrity for compatible IDE devices SMART Use this item to enable or disable the S M A R T Self Monitoring Analysis and Reporting Technology feature Configuration options Disabled Auto Enabled 32 Bit Data Transfer Use this item to enable 32 bit access to maximize the IDE hard disk data transfer rate 3 3 5 PCIPnP Configuration BIOS SETUP UTILITY Advanced Advanced PCI PnP Settings Value in units of PCI clocks for PCI device latency timer register PCI IDE BusMaster Enabled Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2005 American Megatrends Inc PCI Latency Timer The default value is 32 It is recommended to keep the default value unless the installed PCI expansion cards specifications require other settings PCI IDE BusMaster Use this item to enable or di
43. yper Threading Technology Enabled Load Defaults Intel R SpeedStep tm tech Auto pave and Exit XI v02 54 C Copyright 1985 2005 American Megatrends Inc Overclock Mode Use this to select Overclock Mode The default value is Auto Cnfiguration options Auto CPU PCIE Sync and CPU PCIE Async CPU Frequency MHz Use this option to adjust CPU frequency PCIE Frequency MHz Use this option to adjust PCIE frequency Boot Failure Guard Enable or disable the feature of Boot Failure Guard Spread Spectrum This item should always be Auto for better system stability 29 30 Ratio Status This is a read only item which displays whether the ratio status of this motherboard is Locked or Unlocked If it shows Unlocked you will find an item Ratio CMOS Setting appears to allow you changing the ratio value of this motherboard Ratio Actual Value This is a read only item which displays the ratio actual value of this motherboard Ratio CMOS Setting If the ratio status is unlocked you will find this item appear to allow you changing the ratio value of this motherboard If the CPU you adopt supports EIST Intel R SpeedStep tm tech and you plan to adjust the ratio value please disable the option Intel R SpeedStep tm tech in advance Enhance Halt State All processors support the Halt State C1 The C1 state is supported through the native processor instructions HLT and MWAIT and

ASRock Wolfdale1333-DVI User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents