ROHM TCTO series P case Manual
Contents
1. EIAJ ET 7200A Pull direction Label sticking position 5 5 2012 03 Rev C Notice Notes No copying or reproduction of this document in part or in whole is permitted without the consent of ROHM Co Ltd The content specified herein is subject to change for improvement without notice The content specified herein is for the purpose of introducing ROHM s products hereinafter Products If you wish to use any such Product please be sure to refer to the specifications which can be obtained from ROHM upon request Examples of application circuits circuit constants and any other information contained herein illustrate the standard usage and operations of the Products The peripheral conditions must be taken into account when designing circuits for mass production Great care was taken in ensuring the accuracy of the information specified in this document However should you incur any damage arising from any inaccuracy or misprint of such information ROHM shall bear no responsibility for such damage The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products ROHM does not grant you explicitly or implicitly any license to use or exercise intellectual property or other rights held by ROHM and other parties ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such tec2. Apply the specified surge voltage every 5 0 5 min L C Less than 200 of initial value for 30 5 s each time in the atmospheric condition of 85 2 C AC C Within 20 of initial value Repeat this procedure 1 000 times After the specimens leave it at room temperature for Df tan 8 Less than 200 of initial limit over 24h and then measure the sample Loading at Appearance There should be no significant abnormality As per 4 23 JIS C 5101 1 High temperature As per 4 15 JIS C 5101 3 L C Less than 400 of initial limit After applying the rated voltage for 1000 36 0 h without isa Serer discontinuation via the serial resistance of 3Q or less ACIC Within 207 0f Initial value at a temperature of 85 2 C leave the sample at room Df tan 8 Less than 300 of initial limit temperature humidity for 24h and measure the value Terminal Capacitance The measured value should be stable As per 4 35 JIS C 5101 1 strength E As per 4 9 JIS C 5101 3 Appearance There should be no significant abnormality A force is applied to the terminal until it bends to 1mm and by a prescribed tool maintain the condition for 5s See the figure below Unit mm 20 F Apply force R230 SSS4 thickness 1 6mm T 1 1 O 9 Adhesiveness The terminal should not come off As per 4 34 JIS C 5101 1 As per 4 8 JIS C 5101 3 Apply force of 5N in the two directions shown in the
3. ROAM Data Sheet Conductive polymer chip tantalum capacitors Bottom surface electrode type Large capacitance TCTO Series P Case Features P Dimensions Unit mm 1 Conductive polymer used for the cathode material ER 2 Ultra low ESR 3 Small package but big capacitance 4 Screening by thermal shock Unit mm Dimensions P case i 2 0 0 2 Wi 1250 2 0 85 0 2 1 2MAX 0 540 2 Part No Explanation ao GPa Series name Nominal capacitance TCTO Nominal capacitance in pF in 3 digits 2 significant figures followed by the figure 2 Case style representing the number of 0 s P Capacitance tolerance Rated voltage M 20 Rated voltage V 2 5 4 6 3 10 Z CODE 0E 0G OJ TA Taping 8 Tape width R Positive electrode on the side opposite to sprocket hole This specification has possibility of charge due to underdevelopment product Please ask for latest specification to our sales www rohm com 1 5 2012 03 Rev C 2012 ROHM Co Ltd All rights reserved TCTO Series P Case Rated table ESR mQ Rated voltage V DC HF 25 4 63 10 1 0 105 1 5 155 2 2 225 3 3 335 500 4 7 475 500 6 8 685 500 10 106 500 15 156 500 22 226 500 33 336 500 500 47 476 500 500 68 686 500 100 107 Remark Case
4. 5 a Tolerance current 100kHz Part No 85 C 125 C 85 C ee 25 C 1WV 5min 25 C v v V uF uA 55 C 85 C 105 C MQ TCTO P 0E 476 2 5 2 3 2 47 20 11 8 15 15 20 500 TCTOPOE686 O 2 5 2 3 2 68 20 17 0 15 15 20 500 TCTOP0G336 O 3 2 5 33 20 13 2 15 15 20 500 TCTO P 0G 476 3 2 5 47 20 18 8 15 15 20 500 TCTO P 0J 226 6 3 5 8 22 20 13 9 15 15 20 500 TCTO P 0J 336 6 3 5 8 33 20 20 8 15 15 20 500 TCTO P 1A 335 10 8 13 3 3 20 3 3 10 10 15 500 TCTOP1A475 O 10 8 13 4 7 20 4 7 10 10 15 500 TCTO P 1A 685 10 8 13 6 8 20 6 8 10 10 15 500 TCTOP 1A 106 10 8 13 10 20 10 0 15 15 20 500 TCTO P 1A 156 10 8 13 15 20 15 0 15 15 20 500 Tolerance M 20 Under development Packaging specifications Packaging style Unit mm t1 0 05 te 0 1 Pe vss 29 oa 132 Feeding direction Damp proof package One reel is packed in aluminum bag The size of aluminum bag is 240 a x 250 b mm The size up to 230 c mm is to zipper A desiccant is packed with a reel The aluminum bag is heat sealed The label of the same as the label on the reel is placed on the aluminum bag a aa Tan eee www rohm com 2012 ROHM Co Ltd All rights reserved Case code Packaging Packaging style Symbol Basic ordering units P case plastic taping 180mm Reel 8R 3 000pcs Reel P case Unit mm
5. be used for any such special purpose please contact a ROHM sales representative before purchasing If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law you will be required to obtain a license or permit under the Law Thank you for your accessing to ROHM product informations More detail product informations and catalogs are available please contact us ROHM ROHM Customer Support System SEMICONDUCTOR http www rohm com contact www rohm com 2012 ROHM Co Ltd All rights reserved R1120A
6. figure below for 10 1s after mounting the terminal on a circuit board product a Apply force a circuit board Dimensions Refer to External dimensions Measure using a caliper of JIS B 7507 Class 2 or higher grade Resistance to solvents The indication should be clear As per 4 32 JIS C 5101 1 As per 4 18 JIS C 5101 3 Dip in the isopropyl alcohol for 30 5s at room temperature Solderability 3 4 or more surface area of the solder coated As per 4 15 2 JIS C 5101 1 terminal dipped in the soldering bath should As per 4 7 JIS C 5101 3 be covered with the new solder Dip speed 25 2 5mm s Pre treatment accelerated aging Leave the sample on the boiling distilled water for 1 h Solder temp 245 5 C Duration 3 0 5s Solder M705 Flux Rosin 25 IPA 75 Vibration Capacitance Measure value should not fluctuate during As per 4 17 JIS C 5101 1 the measurement Frequency 10 to 55 to 10Hz min Amplitude 1 5mm Appearance There should be no significant abnormality Time 2h each in X and Y directions ae Mounting The terminal is soldered on a print circuit board www rohm com 4 5 2012 03 Rev C 2012 ROHM Co Ltd All rights reserved TCTO Series P Case Data Sheet Standard products list TCTO series P cace Df Rated Category Surge ca Leakage 120Hz ESR voltage voltage voltage
7. size codes P in the above show products line up Under development Marking The indications listed below should be given on the surface of a capacitor The polarity should be shown by O bar on the anode side 1 Polarity 2 Rated DC voltage Due to the small size of P case a voltage code is used as shown below 3 Visual typical example Voltage Rated DC Code Voltage V ee ee eo e Pcase note 1 g 1 n 1 voltage code 2 capacitance code Capacitance Code Nominal Capacitance uF 3 3 4 7 6 8 10 15 22 33 47 z o gt lo jojz 68 manufacture code note 2 voltage code and capacitance code are variable with parts number www rohm com 2012 ROHM Co Ltd All rights reserved 2 5 Data Sheet 2012 03 Rev C TCTO Series P Case Characteristics Item Performance Data Sheet Test conditions based on JIS C 5101 1 and JIS C 5101 3 Operating Temperature 55 C to 105 C Voltage reduction when temperature exceeds 85 C Maximum operatin 85 C temperature with no voltage derating Rated voltage VDC 2 5 4 6 3 10 at 85 C Category voltage VDC 2 3 2 5 8 at 105 C Surge voltage VDC 3 2 5 0 8 13 at 85 C DC Leakage current Shall be satisfied the voltage on Standard list As per 4 9 JIS C 5101 1 As per 4 5 1 JIS C 5101 3 Voltage Rated
8. hnical information The Products specified in this document are intended to be used with general use electronic equipment or devices such as audio visual equipment office automation equipment commu nication devices electronic appliances and amusement devices The Products specified in this document are not designed to be radiation tolerant While ROHM always makes efforts to enhance the quality and reliability of its Products a Product may fail or malfunction for a variety of reasons Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury fire or any other damage caused in the event of the failure of any Product such as derating redundancy fire control and fail safe designs ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual The Products are not designed or manufactured to be used with any equipment device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury such as a medical instrument transportation equipment aerospace machinery nuclear reactor controller fuel controller or other safety device ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes If a Product is intended to
9. ition 5 cycles L C Less than 1000 of initial limit 1 cycle steps 1 to 4 without discontinuation AC C Within 20 of initial value Temp Time Df tan Less than 300 of initial limit 1 5543 C 30 3min 2 Room temp 3min or less 3 105 2 C 30 3min 4 Room temp 3min or less Moisture Appearance There should be no significant abnormality As per 4 22 JIS C 5101 1 resistance The indications should be clear As per 4 12 JIS C 5101 3 5 TEE After leaving the sample under such atmospheric Be Less Ihan 300 r inital limit condition that the temperature and humidity are AC C Within 30 20 of initial value 40 2 C and 90 to 95 RH respectiveiy for 500 12h ae leave it at room Df tan Less than 300 of initial limit temperature for 24h and then measure the sample www rohm com 2012 ROHM Co Ltd All rights reserved 3 5 2012 03 Rev C TCTO Series P Case Data Sheet Item Performance Test conditions based on JIS C 5101 1 and JIS C 5101 3 Temperature Temp 55 C As per 4 29 JIS C 5101 1 Stability As per 4 13 JIS C 5101 3 AC C Within 0 20 of initial value Df tan Shall be satisfied the voltage on Standard list L C Temp 105 C AC C Within 50 0 of initial value Df tan Shall be satisfied the voltage on Standard list L C Less than 1 000 of initial value Surge voltage Appearance There should be no significant abnormality pe ber HPE ae
10. voltage for 5min Capacitance tolerance Shall be satisfied allowance range 20 As per 4 7 JIS C 5101 1 As per 4 5 2 JIS C 5101 3 Measuring frequency 120 12Hz Measuring voltage 0 5Vrms 1 5 to 2V DC Measuring circuit DC Equivalent series circuit Tangent of loss angle Shall be satisfied the voltage on As per 4 8 JIS C 5101 1 Df tan Standard list As per 4 5 3 JIS C 5101 3 Measuring frequency 120 12Hz Measuring voltage 0 5Vrms 1 5 to 2V DC Measuring circuit DC Equivalent series circuit ESR Shall be satisfied the voltage on As per 4 10 JIS C 5101 1 Standard list As per 4 5 4 JIS C 5101 3 Measuring frequency 100 10kHz Measuring voltage 0 5Vrms or less Measuring circuit DC Equivalent series circuit Resistance to Appearance There should be no significant abnormality As per 4 14 JIS C 5101 1 Soldering heat The indications should be clear As per 4 6 JIS C 5101 3 aes Dip in the solder bath L C Less than 300 of initial limit Solder temp 240 5 C AC C Within 20 of initial value Duration 10 0 5s Repetition zi Df tan 6 Less than 300 of initial limit After the specimens leave it at room temperature for over 24h and then measure the sample Temperature Appearance There should be no significant abnormality As per 4 16 JIS C 5101 1 cycle The indications should be clear As per 4 10 JIS C 5101 3 en rer Repet
Download Pdf Manuals
Related Search
ROHM TCTO series P case Manual