ROHM TCT series PL case Manual
Contents
1. 1 Polarity 2 Rated DC voltage 3 Capacitance value The polarity should be shown by O Due to the small size of PL case a voltage code is used as shown below Due to the small size of PL case a capacitance code is used as shown below Voltage Rated DC Capacitance Nominal Code Voltage V Code Capacitance uF e 2 5 A 1 0 g 4 E 1 5 j 6 3 J 2 2 A 10 N 3 3 Cc 16 S 4 7 D 20 WwW 6 8 E 25 a 10 Vv 35 e 15 j 22 n 33 s 47 w 68 a 100 a 150 PL case note 1 n 2 1 voltage code 2 capacitance code note 2 voltage code and capacitance code are variable with parts number www rohm com manufacture code 2011 ROHM Co Ltd All rights reserved bar on the anode side 2 6 Data Sheet 2011 12 Rev H TCT Series PL Case Characteristics Item Operating Temperature Performance 55 C to 125 C Test conditions based on JIS C 5101 1 and JIS C 5101 3 Voltage reduction when temperature exceeds 85 C Maximum operating temperature with no voltage derating 85 C Rated voltage VDC 2 5 4 6 3 10 16 20 25 35 at 85 C Category voltage VDC 1 6 2 5 4 6 3 10 13 16 22 at 125 C Surge voltage VDC 3 2 5 2 8 13 20 26 32 44 at 85 C DC Leakage current Shall be satisfied the voltage on Standard list As per 4 9 JIS2. 24 02s 105 Taping PL case 1 75 0 1 3 50 05 Positiv Electrode Feeding direction Packaging style Case code Packaging Packaging style Symbol Basic ordering units PL case plastic taping 180mm Reel R 3 000pcs Reel PL case 11 4 1 0 Pull direction Label sticking position Unit mm EIAJ ET 7200A ee 6 6 2011 12 Rev H 2011 ROHM Co Ltd All rights reserved Notice Notes No copying or reproduction of this document in part or in whole is permitted without the consent of ROHM Co Ltd The content specified herein is subject to change for improvement without notice The content specified herein is for the purpose of introducing ROHM s products hereinafter Products If you wish to use any such Product please be sure to refer to the specifications which can be obtained from ROHM upon request Examples of application circuits circuit constants and any other information contained herein illustrate the standard usage and operations of the Products The peripheral conditions must be taken into account when designing circuits for mass production Great care was taken in ensuring the accuracy of the information specified in this document However should you incur any damage arising from any inaccuracy or misprint of such information ROHM shall bear no respo
3. C 5101 1 As per 4 5 1 JIS C 5101 3 Voltage Rated voltage for 5min Capacitance tolerance Shall be satisfied allowance range 20 As per 4 7 JIS C 5101 1 As per 4 5 2 JIS C 5101 3 Measuring frequency 120412Hz Measuring voltage 0 5Vrms 1 5 to 2V DC Measuring circuit DC Equivalent series circuit Tangent of loss angle Df tan 8 Shall be satisfied the voltage on Standard list As per 4 8 JIS C 5101 1 As per 4 5 3 JIS C 5101 3 Measuring frequency 120412Hz Measuring voltage 0 5Vrms 1 5 to 2V DC Measuring circuit DC Equivalent series circuit Impedance Shall be satisfied the voltage on Standard list As per 4 10 JIS C 5101 1 As per 4 5 4 JIS C 5101 3 Measuring frequency 100 10kHz Measuring voltage 0 5Vrms or less Measuring circuit DC Equivalent series circuit Resistance to Appearance There should be no significant abnormality As per 4 14 JIS C 5101 1 Soldering heat The indications should be clear As per 4 6 JIS C 5101 3 E Dip in the solder bath L C Less than initial limit Solder temp 260 5 C AC C Within 20 of initial value Duration 50 58 EEE Repetition zi Df tan 8 Less than 200 of initial limit After the specimens leave it at room temperature for over 24h and then measure the sample Temperature Appearance There should be no significant abnormality As per 4 16 JIS C 5101 1 cycle The indicati
4. measurement Appearance There should be no significant abnormality Standard list TCT Series PL Case Part No TCT PL OE 686M8R x TCT PL OE 157M8R TCT PL 0G 476M8R TCT PL 0G 107M8R TCT PL OJ 336M8R TCT PL OJ 476M8R TCT PL1A 226M8R TCT PL1A 336M8R TCT PL 1C 106M8R TCT PL 1D 335M8R TCT PL 1D 685M8R TCT PL 1E 155M8R TCT PL 1E 225M8R _ TCT PL 1V 105M8R k Under development www rohm com Rated voltage 85 C v Category voltage 125 C v 2011 ROHM Co Ltd All rights reserved Surge voltage 85 C v As per 4 17 JIS C 5101 1 Frequency 10 to 55 to 10Hz min Amplitude 1 5mm Time 2h each in X and Y directions Mounting The terminal is soldered on a print circuit board Leakage 1 ae Impedance Tolerance current 100kHz 25 C 1WV 5min 25 C uA 55 C 85 C 125 C Q 20 8 5 60 30 40 4 20 125 60 30 40 4 20 188 60 30 40 4 20 9 4 30 20 30 4 20 136 60 30 40 4 20 20 60 30 40 4 20 10 4 30 20 30 4 20 148 60 30 40 4 20 11 30 20 30 5 20 165 60 30 40 4 20 3 2 30 20 30 6 20 1 4 30 20 30 8 20 19 30 20 30 6 20 28 30 20 30 6 20 0 8 30 20 30 8 20 11 30 20 30 8 20 0 7 30 20 30 8 5 6 2011 12 Rev H TCT Series PL Case Data Sheet Packaging specifications Unit mm Pm 16
5. ROHM Data Sheet SEMICONDUCTOR Chip Tantalum capacitors Bottom surface electrode type Large capacitance TCT Series PL Case Features PL Dimensions Unit mm 1 Vital for all hybrid integrated circuits board application 2 Wide capacitance range 3 Screening by thermal shock Anode mark Unit mm PL case 2 0 0 2 1 25 0 2 0 85 0 2 0 9 0 1 0 5 0 2 Part No Explanation MAA m 2 G O O series name Nominal capacitance TCT Nominal capacitance in pF in 3 digits 2 significant figures followed by the figure case style representing the number of 0 s PL Capacitance tolerance ated voltage M 20 Rated voltage V 2 5 4 6 3 10 16 20 25 35 CODE OE 0G OJ 1A 1C 1D ME AV taping 8 Reel width 8mm R Positive electrode on the side opposite to sprocket hole www rohm com 1 6 2011 12 Rev H 2011 ROHM Co Ltd All rights reserved TCT Series PL Case Rated table Rated voltage V DC 2 5 6 3 10 16 20 25 35 PL PL PL PL PL PL PL PL PL PL PL PL PL PL 100 107 PL PL 150 157 PL Remark Case size codes PL in the above show products line up Under development Marking The indications listed below should be given on the surface of a capacitor
6. alue Df tan Shall be satisfied the voltage on Standard list L C Less than 1000 of initial limit Temp 125 C AC C Within 20 0 of initial value Df tan Shall be satisfied the voltage on Standard list L C Less than 1250 of initial limit Surge voltage Appearance There should be no significant abnormality As per 4 26JIS C 5101 1 As per 4 14JIS C 5101 3 L C Less than 200 of initial value Apply the specified surge voltage via the serial resistance of m ae 1kQ every 5 0 5 min O AGIO Within Oe ofinital value for 30 5 s each time in the atmospheric condition of 85 2 C Df tan Less than 200 of initial limit Repeat this procedure 1 000 times After the specimens leave it at room temperature for over 24h and then measure the sample Loading at Appearance There should be no significant abnormality As per 4 23 JIS C 5101 1 High temperature a As per 4 15 JIS C 5101 3 L C Less than 200 of initial limit After applying the rated voltage for 1000 36 0 h without a 5 discontinuation via the serial resistance of 3Q or less AC C Within 20 of initial value at a temperature of 85 2 C leave the sample at room Df tan 8 Less than 200 of initial limit temperature humidity for over 24h and measure the value Terminal Capacitance The measured value should be stable As per 4 35 JIS C 5101 1 strength 3 Appearance There should be no significant abnormality AS per 49 dS G 910173 A force is applied to the ter
7. high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury such as a medical instrument transportation equipment aerospace machinery nuclear reactor controller fuel controller or other safety device ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes If a Product is intended to be used for any such special purpose please contact a ROHM sales representative before purchasing If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law you will be required to obtain a license or permit under the Law Thank you for your accessing to ROHM product informations More detail product informations and catalogs are available please contact us ROHM ROHM Customer Support System SEMICONDUCTOR http www rohm com contact www rohm com 2011 ROHM Co Ltd All rights reserved R1120A
8. minal until it bends to 1mm and by a prescribed tool maintain the condition for 5s See the figure below Unit mm 20 50 H F Apply force R230 i a A Z f thickness 1 6mm www rohm com 2011 ROHM Co Ltd All rights reserved 4 6 2011 12 Rev H TCT Series PL Case Item Adhesiveness Performance The terminal should not come off Data Sheet Test conditions JIS C 5101 1 and JIS C 5101 3 As per 4 34 JIS C 5101 1 As per 4 8 JIS C 5101 3 Apply force of 5N in the two directions shown in the figure below for 10 1s after mounting the terminal on a circuit board product 4 E Apply force a circuit board Dimensions Refer to External dimensions Measure using a caliper of JIS B 7507 Class 2 or higher grade Resistance to solvents The indication should be clear As per 4 32 JIS C 5101 1 As per 4 18 JIS C 5101 3 Dip in the isopropyl alcohol for 30 5s at room temperature Solderability 3 4 or more surface area of the solder coated terminal dipped in the soldering bath should be covered with the new solder As per 4 15 2 JIS C 5101 1 As per 4 7 JIS C 5101 3 Dip speed 25 2 5mm s Pre treatment accelerated aging Leave the sample on the boiling distilled water for 1 h Solder temp 245 5 C Duration 3 0 5s Solder M705 Flux Rosin 25 IPA 75 Vibration Capacitance Measure value should not fluctuate during the
9. nsibility for such damage The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products ROHM does not grant you explicitly or implicitly any license to use or exercise intellectual property or other rights held by ROHM and other parties ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information The Products specified in this document are intended to be used with general use electronic equipment or devices such as audio visual equipment office automation equipment commu nication devices electronic appliances and amusement devices The Products specified in this document are not designed to be radiation tolerant While ROHM always makes efforts to enhance the quality and reliability of its Products a Product may fail or malfunction for a variety of reasons Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury fire or any other damage caused in the event of the failure of any Product such as derating redundancy fire control and fail safe designs ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual The Products are not designed or manufactured to be used with any equipment device or system which requires an extremely
10. ons should be clear As per 4 10 JIS C 5101 3 F _ Repetition 5 cycles L C Less than 200 of initial limit 1 cycle steps 1 to 4 without discontinuation AC C Within 20 of initial value Temp Time Df tan 8 Less than 200 of initial limit 1 5543 C 30 3min 2 Room temp 3min or less 3 125 2 C 30 3min 4 Room temp 3min or less After the specimens leave it at room temperature for over 24h and then measure the sample Moisture Appearance There should be no significant abnormality As per 4 22 JIS C 5101 1 resistance The indications should be clear As per 4 12 JIS C 5101 3 aCe ee After leaving the sample under such atmospheric ae pose than 2007s Orinta Nimit condition that the temperature and humidity are AC C Within 20 of initial value 60 2 C and 90 to 95 RH respectiveiy for 500 12h leave it at room Df tan Less than 200 of initial limit temperature for over 24h and then measure the sample www rohm com 3 6 2011 ROHM Co Ltd All rights reserved 2011 12 Rev H Data Sheet TCT Series PL Case Data Sheet Item Performance Test conditions based on JIS C 5101 1 and JIS C 5101 3 Temperature Temp 55 C As per 4 29 JIS C 5101 1 Stability As per 4 13 JIS C 5101 3 AC C Within 0 15 of initial value Df tan Shall be satisfied the voltage on Standard list L C T Temp 85 C AC C Within 15 0 of initial v
Download Pdf Manuals
Related Search
ROHM TCT series PL case Manual