camera Manual(1)(2)
Contents
1. The amount of light reaching the film plane is determined by a combination of the shutter speed and the lens aperture Since the two are interrelated different combinations will give the same degree of exposure A one step change in shutter speed or a one stop change in aperture setting will either halve or double the degree of exposure For example a shutter speed of 1 125 sec lets in twice as much light as a setting of 1 250 sec and only half as much light at 1 60 sec For an aperture setting of f 11 twice as much light as f 16 and half at much as 8 is let in Thus if the correct exposure for a particular picture taking situation is 1 125 at f 11 then 1 60 at f 16 or 1 250 at f 8 will give the same exposure The following table illustrates the interrelation between shutter speed and aperture The best combination will depend on the results you want Use fast shutter speeds to freeze motion use slow speeds to produce a deliberate blur See the example pictures on the opposite page Also small apertures give greater depth of field while large apertures restrict sharp focus to the main subject See page 26 A good rule to follow in preventing camera shake is to select a minimum shutter speed which is the reciprocal of the focal length of the lens in use For example when using a normal 50mm lens select a speed no slower than 1 60 sec the closest number to 1 50 For a 500mm super telephoto use no less than 1 500 sec and so fo2. symbol appears in the finder Release the preview button and take the shot For non AI lenses or accessories without automatic diaphragms On AUTO Stop the lens down manually until the desired shutter speed appears in the finder Then take the picture On MANUAL Adjust the shutter speed or aperture until the sign appears For fixed aperture reflex lenses photomicrography or astrophotography On AUTO No control is necessary On MANUAL Adjust the shutter speed dial until the appears Mirror lockup lever 3 Niele When using super telephoto lenses or doing photomicrography it becomes necessary to reduce camera vibration to the absolute minimum To lock the reflex viewing mirror in the up position push in the depth of field preview button and rotate the lever counterclockwise until it stops Note Two Nikkor lenses require that the mirror be locked up before mounting the Fisheye Nikkor 6mm f 5 6 and OP Fisheye Nikhor 10mm f 5 6 Caution With the mirror locked up you should not operate the camera on automatic Even though the LCD continues to show you the shutter speed automatically selected by the camera this speed will not produce the correct exposure Self timer The F3 High Eyepoint camera s blinking self timer provides a 10 sec delay in shutter release To operate the self timer 1 Push the self timer lever 4 ig to uncover the red dot 4 pa Ma wo 4 2 Push the shutter
3. flashtube module for convenient bounce flash Speedlights SB 11 and 14 When your require a bracket mounting unit Nikon offers two the SB 11 and SB 14 The powerful SB 11 has a guide number of 36 ISO 100 meters or 118 ISO 100 feet and features a 120 tilting flash head for bounce flash The SB 14 requires a separate battery pack It has a guide number of 32 ISO 100 meters or 105 ISO 100 feet and tilts 120 and rotates 120 for total bounce control For automatic TTL control these units must be used with TTL remote cord SC 12 Speedlight SB 21A The SB 21A lets you use TTL automatic exposure for macro photography and a convenient focus illuminator ensures pin point focus adjustment The flash head offers a 65 horizontal and 85 vertical angle of coverage and a wide illuminahon panel lets you shoot flash to subject distances closer than 40mm approx 1 6 in SB 21A can be used with an external power source AC or DC Guide number is 13 at ISO 100 meters or 43 at ISO 100 feet with internal batteries and 15 or 49 with external power source F3 High Eyepoint with SB 17 F3 High Eyepoint OTHER ACCESSORIES Eyepiece Correction Lenses Screwing into the finder eyepiece four separate lenses are provided so that near and farsighted photographers can use the F3 High Eyepoint camera without their glasses They are available in 2 O 1 and 2 diopters representing the combined dioptry of the finder and lens Eyep
4. 80 0 64 N a l N gt J 5S Hll sl ells SI SA l Fea Table Slowest shutter speed at full aperture with any lens How to read the EV chart e Full aperture metering Example Lens maximum aperture f 1 4 ASA ISO film speed 100 Working aperture 5 6 By referring to the f 1 4 column in Section A and the EV values indicated for ASA ISO 100 in Section D you will find that the EV range for an f 1 4 lens at ASA ISO 100 is 1 to 18 Now refer to Section B and single out the f 5 6 indication for ASA ISO 100 Go diagonally down until the protruding line intersects with Section C s vertical line for the shutter speed of 8 sec the F3 High Eyepoint camera s slowest shutter speed From this point of intersection follow the horizontal line that leads to Section D s EV value for ASA ISO 100 and you will obtain an EV value of 2 Start again from the f 5 6 indication for ASA ISO 100 in Section B and go down diagonally until the protruding line intersects with Section C s vertical line for the shutter speed of 1 2000 sec the F3 High Eyepoint camera s fastest shutter speed this time Then follow the horizontal line that leads to Section D s EV value for ASA ISO 100 and you will get a reading ot EV 16 This means that an f stop of f 5 6 at ASA ISO 100 and a shutter speed of from 8 to 1 2000 sec has an effective EV range of 2 to 16 which is well within the F3 High Eyepoint camera s metering range ot EV 1 to EV 18 The area encompassed by the
5. second section CONTROLS IN DETAIL A few minutes wisely invested now will pay off in years of rewarding photographic experiences BASIC OPERATION 1 Remove the battery chamber lid ag EI Use a coin to twist the lid counter clockwise to unscrew it 2 Install the batteries Insert the two 1 5V silver oxide batteries supplied with the camera making sure that the signs are up 3 Replace the battery chamber lid Slip the battery clip back into the camera body and screw it tightly into place 4 Move the power switch 4 to uncover the red dot gp eh tel This turns the camera on and makes it ready for exposure reading and shooting 5 Touch the shutter release button 53 lightly Stet This activates the exposure meter The meter stays on for 16 seconds after you take your finger off the button and turns itself off automatically to conserve battery power 6 Check battery power Look through the viewfinder cat at the liquid crystal display LCD The shutter speed should be displayed to show that the batteries have been properly installed and their power is adequate If not replace both batteries 7 Mount the lens onto the camera Grasp the lens by its mounting ring oF Then line up the focusing index aa on the lens with the white dot ag on the camera body and twist the lens counterclockwise until it clicks into place To remove Push the lens release button a8 and turn the lens cloc
6. the viewfinder Using a standard of ASA ISO 25 film you may be assured of at least a four second speed regardless of the aperture of the lens used as long as the lens is set at full aperture refer to Table Using ASA ISO 400 at f 1 4 the slowest speed is 1 4 second however as the aperture is closed down the functioning shutter speed becomes progressively slower until we reach f 8 when the slowest speed of eight seconds is functioning e Auto exposure control with stop down metering When using a bellows or other extension equipment which disengages the meter coupling device it is necessary to revert to stop down metering Certain limitations are imposed in this mode As lens to film distance is increased the metering range EV range changes proportionately For example when an f 2 lens is used at 2 1 reproduction twice life size the effective f number is f 5 6 When used at f 8 the effective f number is f 22 When pictures are taken under minimal light levels it is desirable to use a high speed film ASA ISO 160 or higher Using Tri X at film speed 400 with stop down metering with an effective f number of f 8 the shutter speed range would be from 1 4 second to 1 2000 Should the light level drop below EV 6 it would be out of the shutter speed range of the meter speed lowest shutter speed sec DH 400 200 4000 600 30 CO I KOT o D jars gt N pm N O E 00 160 00
7. you use a Nikon dedicated electronic flash unit which operates with a low voltage current Use of any other flash which operates af high voltages may damage the camera s circuitry Any damage caused by such use is not covered by the Nikon Warranty 2 Even with the couplerer the Nikon Speedlight SB 19 SB 18 SB 16B and SB E cannot be used with an F3 High Eyepoint camera when a finder other than the standard DE 3 or Eye Level Finder DE 2 is used Sync terminal 37 gt y a A separate sync terminal with a protective screw in cover is provided on the Nikon F3 High Eyepoint camera It accepts all standard plug in sync cords plus it is threaded for use with a Nikon screw in sync cord When using flash bulbs or an electronic flash without a hot shoe it is necessary to use the sync terminal Use the following table to determine the correct synchronization speed to set on the camera Shutter speed sec Synchronized Note When using a special electronic flash unit with provision for time leg an electronic flash unit with long flash duration time or the Medical Nikkor 120mm f 4 IF adjust shutter speed down to 1 30 sec or slower Viewfinder illuminator 43 TE A convenient built in viewfinder illuminator lets you see the liquid crystal display shutter speed including the aperture even in dim light While the LCD is displayed in the finder push the illuminator button ar Note The power switch must he turned on and the
8. DW 4 6X High Magnification Finder DE 3 provided with eyepiece shutter 0 75X magnification with 50mm lens set at infinity virtually 100 frame coverage Viewfinder display Liquid crystal display LCD shows shutter speed on Auto 2000 indicates overexposure 8 underexposure on Manual M appears with indicating overexposure underexposure and correct exposure LED ready light glows when Nikon dedicated flash unit is completely recycled aperture in use also shown through aperture direct readout ADR window Viewfinder illuminator Provided illuminates both liquid crystal display and ADR f number Film advance lever Wound in single stroke or series of strokes 30 stand off angle and 140 winding angle shutter speed automatically set to 1 80 sec until frame 1 for fast loading when shutter speed dial is set to A or 1 125 sec and above Frame counter Additive type self resetting Film rewind Folding crank with rewind button in baseplate Eyepiece shutter Provided prevents stray light from entering viewfinder from the rear Focusing screen Type K as standard interchangeable with 20 other types Depth of field preview button Provided coaxial with mirror lockup lever Reflex mirror Automatic instant return type with lockup facility incorporates air damper Multiple exposure lever Provided disengages frame counter for correct count Camera back Hinged interchangeable type memo holder provided Power switch
9. Nomenclature OONDAORWNM Shutter speed dial locking button Depth of field preview button Mirror lockup lever Neckstrap eyelet Self timer LED Backup mechanical release lever Expose memory lock button Lens mounting flange Reflex mirror ADR window Film rewind knob ASA ISO film speed Exposure compensation dial Sync terminal Lens mounting index Lens release button Meter coupling lever release button Meter coupling lever Viewfinder illuminator Motor drive coupling Motor drive positioning hole Film rewind button Memo holder Tripod Motor drive coupling socket Motor drive electrical contacts Battery chamber lid Motor drivecoupling cover Depth of field indicators Mounting ring Focusing ring Aperture ring Meter coupling ridge Finder mounting release levers Exposure compensation scale Exposure compensation index Film rewind crank Hot shoe contacts Accessory shoe Camera back lock lever Exposure compensation locking button ASA ISO film speed scale Eyepiece shutter lever Viewfinder eyepiece Shutter speed index Aperture Focusing index Meter coupling shoe Distance scale Aperture direct readout scale Viewfinder illuminator button Self timer lever Self timer ON index Power switch ON index Power switch Multiple exposure lever Shutter release button Frame counter Film adva
10. Provided Batteries Two 1 55V silver oxide cells Eveready EPX76 D76 or equivalent two 1 5V alkaline manganese cells or one 3V lithium battery when MD 4 motor drive is attached camera gets battery power from batteries in motor drive Dimensions Approx 148 5mm W x 101 5mm H x 69 0mm D Weight Approx 760g with DE 3 High Eyepoint Finder Specification and designs are subject to change without notice IMPORTANT The camera body you have purchased is packaged separately from the lens Before mounting the lens check if it is capable of Automatic Maximum Aperture Indexing AI operation with your camera body by verifying that the lens aperture ring is fitted with a meter coupling ridge as illustrated at the right Note that the Ai mark on the cover of the instruction sheet provided with AI Nikkor lenses is your assurance that the lens offers the AI feature If the lens is fitted with the mirror coupling ridge it is fully capable of full aperture exposure measurement and automatic maximum aperture indexing to attach it to the camera follow the directions provided in the BASIC OPERATION section of this instruction manual If the lens is non AI stop down exposure measurement is required with the camera body s meter coupling lever locked up to lock up the lever follow the directions in the Meter coupling lever section of CONTROLS IN DETAIL
11. ackground General film with continuous gradation Approx 1 to 2 stops Approx 1 1 2 to 2 1 2 stops for black Film of documents and drawings cere on wie bakeroa photographed 0 to approx 1 2 stop for white letters on black background ASA film speed dial 455 M S The scale as on the ASA dial has numbered settings for speeds from ASA 12 to 6400 Two dots between each pair of ASA numbers stand for intermediate settings such as 64 80 etc The table below gives the speeds for all intermediate settings 7 4000 160 a20 Fac 50 2500 450 ASA is a numerical rating of the film s sensitivity to a given amount of light The higher the number the greater the sensitivity and vice versa The ASA of your film is indicated on the cartridge itself It is also printed on the film carton and on the data sheet packed inside EXP oSuacs PR 135 3 Memo holder g M 2 As a reminder of the film type and the number of exposures on the roll in use clip off the end of the film carton and insert it into the memo holder Note At the B setting unless you hold the shutter release button down all the way the shutter may close prematurely Shutter release button ga ciel Slight pressure on the shutter release button switches on the exposure meter Pushing the button all the way down releases the shutter The shutter release button is threaded at the center to accept a standard cable release When battery power
12. ate Once you attach the MD 4 to your camera you ll never want to take it off The Firing Rate Converter MK 1 is available as a special accessory for a motor driven F3 High Eyepoint camera It screws into the tripod socket of the MD 4 and plugs into the remote terminal to provide three firing rates 1 2 or 3 frames per second It has its own handy trigger button for use in vertical format shooting The Magazine Back MF 4 for shooting up to 250 frames without changing film is also available as an option Possible with NiCd battery pack at 1 125 sec or above with the mirror locked up Electronic Flash Units Nikon Speedlights are dedicated electronic flash units and provide the perfect complement to your F3 High Eyepoint camera Just set the aperture and flash output is measured through the lens for correct exposures regardless of the lens in use Speedlights SB 16A and 17 The SB 16A and SB 17 mount directly on the camera for automatic TTL flash exposure control The SB 16A features two flash heads for more natural bounce flash portraits main head tilts 90 and rotates 270 the secondary head faces straight ahead to provide catchlight in subject s eyes Main head zooms in and out to match the coverage of 28 35 50 and 85mm lenses with a guide number of 32 ISO 100 and meters or 105 ISO 100 feet The light compact SB 17 has a guide number of 25 ISO 100 meters or 82 ISO 100 feet and features a rotating flash head and tilting 90
13. attempt to disassemble or repair the camera yourself These delicate procedures should be left to an authorized repairman SPECIFICATIONS Type of camera 35mm single lens reflex Picture format 24mm x 36mm standard 35mm film format Lens mount Nikon bayonet mount Lenses Nikkor 50 1 2 50 1 4 50 1 8 and Nikon Series E 50 1 8 as standard more than 70 Nikkor and Nikon Series E lenses available Shutter Horizontal travel titanium focal plane shutter Shutter speeds Auto Electromagnetically controlled stepless speeds from 8 to 1 2000 sec Manual Quartz electromagnetically controlled discrete speeds from 8 to 1 2000 sec plus B and X 1 80 sec Mechanical T setting on shutter speed dial and 1 60 sec when using backup mechanical release lever Shutter release Electromagnetic shutter release initial pressure on shutter release button switches on meter after power switch is turned on meter then remains on for 16 sec after finger is taken off button Backup mechanical release lever Trips shutter at 1 60 sec regardless of shutter speed dial setting except at T used when batteries are dead Self timer Quartz timed 10 sec delayed exposure LED blinks at 2 Hz for first 8 sec then at 8 Hz for last 2 sec Exposure control Aperture priority automatic exposure with manual override and backup mechanical control through the lens full aperture metering via silicon photo diode SPD with centerweighted metering pattern and meterin
14. cannot be read However this situation will return to normal when the temperature drops 2 Avoid storing the camera in excessively hot places such as in a car parked in direct sunlight or inside the trunk You may shorten the LCD s life by doing so 3 When the temperature goes below freezing the response time decreases as the liquid crystal becomes more viscose EV RANGE OF THE CAMERA The camera s meter may be used only within the shutter speed range covered by the exposure value EV range of the meter which varies with the aperture and ASA ISO settings The chart on page 35 shows the relationships between the f stop shutter speed and film speed indicating the slowest functioning shutter speed for metering purposes with any film speed aperture combination Careful attention to the following instructions will assure precise exposure automatically over the complete exposure control and meter range capabilities of your Nikon F3 High Eyepoint camera e Auto exposure control at full aperture For example with an f 1 4 lens and ASA ISO 100 film the automatic shutter will function down to one second with the lens set at f 1 4 and proportionately slower as the aperture is closed However practically speaking even if the shutter speed aperture combination is outside the guaranteed EV range shown in Section C of the EV Chart you can still obtain good exposures at either the AUTO or MANUAL setting unless 2000 or 8 appears in
15. compatible with which lenses consult the instruction sheet supplied with the lens Focusing Screen Selector Guide Type A Matte Fresnel field with 3mm circular split image rangefinder spot and 12mm reference circle Rapid and accurate focusing Excellent for general photography Type B Matte Fresnel field with 3mm fine ground matte focusing spot and 12mm reference circle Good for general photography especialy with long lenses Type C Fine ground matte field wth 4mm clear spot and cross hair For photomicrography astrophotography and other high magnification applications using parallax focusing on aerial images Type E Matte Fresnel field with 3mm fine ground matte spot 12mm reference circle and etched horizontal and vertical lines Ideal for architectural photography Type G Clear Fresnel field with extra bright 12mm microprism focusing spot for viewing and focusing in poor light Four models Gl G4 are available corresponding to specific focal length lenses Depth of field cannot be observed Type H Clear Fresnel field with microprism focusing pattern over the entire screen area Permits rapid focusing on any part of the screen with optimum edge to edge brightness in poor light Available in four models H1 H4 corresponding to particular focal length lenses Type J Matte Fresnel field with central microprism focusing spot and 12mm circle Good for general photography Type K Co
16. ds from 1 2000 sec to 8 sec including X B and T To move the shutter speed dial off A depress the locking button 3 D as you rotate the dial counterclockwise to the 1 2000 sec setting You can then rotate the dial freely between any setting except X which like A is a locked setting Shutter speeds from 1 2000 sec to 1 2 sec are engraved in white 1 to 8 seconds and B in orange and T and X in white 1 60 sec is in red indicating the highest manual shutter speed for proper synchronization with electronic flash except X When the camera is on manual an M appears to the left of the liquid crystal shutter speed display inside the viewfinder In addition above the M the following symbols appear and indicating underexposure overexposure and correct exposure respectively To obtain correct exposure simply turn the shutter speed dial and or aperture ring until the symbol appears The F3 has two separate settings for time exposures On B the shutter remains open for as long as the shutter release button is depressed On T the shutter stays open until the dial is rotated to another setting making it ideal for really long time exposures Being a mechanical setting T will not cause battery drain regardless of how long the shutter remains open X provides a shutter speed setting of 1 80 sec It is used to provide proper synchronization with electronic flash units other than the Nikon SB 12
17. er upright keep its nozzle more than 30cm away from the lens surface and move the nozzle around so that the stream of air is not concentrated in one spot 2 Clean the inside of the camera Brush out the inside of the camera periodically using a soft brush Do not exert pressure on the shuter curtains as this may damage them Also keep the mirror free from fingerprints and dust 3 Keep the camera away from water Avoid excessive moisture When using the camera near water guard against splashes especially sallwater spray 4 Do not expose the camera to high temperatures Keep the camera away from places where the temperature is apt to be high such as on the beach under direct sunlight or in the trunk of a car Als AU Pr PARER UN TRESS BC W e k MUN COO Ae m Te i F 5 i z m m m lt i 5 Store the camera properly Store the camera in a carrying case to protect it from dust Avoid storing the camera in excessively hot cold or damp places Always attach a body cap to the camera body and a front and rear lens cap to the lens when storing them to prevent dust from getting inside the body or on the lens surfaces To keep your F3 High Eyepoint in top working order it is recommended that you trip the shutter and operate the film advance lever a few times each month with or without film loaded in the camera Remove the batteries before storing the camera for an extended period of time 6 Never
18. fails the F3 s electromagnetically controlled shutter ceases to operate You cannot release the shutter release button unless you use the backup mechanical release lever To lock the shutter release button when the camera is not in use turn the power switch to the OFF position Film advance lever 5 TL The film advance lever is specially contoured to fit the thumb and is coaxial with the shutter release button It has a 30 stand off with a throw of 140 and may be operated in one complete stroke or a series of shorter ones Frame counter a wh To keep track of the number of exposed frames the frame counter is graduated from two frames below 0 up to 40 Blue numerals appear every 5 frames 0 5 10 etc with dots in between White marks at 12 20 24 and 36 indicate the number of frames available on most film cartridqes When making blank shots with the shutter speed dial set to A the shutter will fire at 1 80 sec until the frame counter reaches 1 In addition the LCD shows 80 in the finder Or if you set the dial manually between 1 125 and 1 2000 sec the shutter will still fire at 1 80 sec In the finder an M80 is displayed However if the speed is manually set to 1 80 sec X or below the shutter will fire at the speed set and the speed will be displayed by the LCD Therefore to speed up film loading set the dial to A or to 1 80 sec X or above T should not be used when making blank shots as the shu
19. g circuits incorporated into camera body meter works with all viewfinders Film speed range ASA ISO 12 to ASA ISO 6400 Metering range EV 1 to EV 18 at ASA ISO 100 with f 1 4 lens Exposure compensation dial Provided 2 EV in one third increments Exposure memoy lock Provided operates on Auto to electronically lock in shutter speed Accessory shoe Provided special Nikon type located at base of rewind knob accepts Nikon SB 12 SB 16A or SB 17 shoemounting electronic flash unit or TTL connecting cord from SB 11 or SB 14 for TTL direct flash output control using camera s SPD metering cell Flash synchronization Speeds up to 1 80 sec with electronic flash with a Nikon dedicated flash unit flash sync is automatically set to 1 80 sec when shutter speed dial is set at A or 1 125 sec or above flash synchronizes with shutter speed set at slower shutter speed settings threaded sync terminal provided for off camera or multiple flash photography Auto flash control TTL direct flash control governs a Nikon dedicated flash unit s flash output using camera s SPD sensor effective ASA ISO range from ASA ISO 25 to ASA ISO 400 Viewfinder High eyepoint pentaprism type DE 3 as standard entire viewfinder image plus exposure information visible with the eye located up to 25mm approx one inch away from the eyepiece interchangeable with five other types DX 1 AF Finder DE 2 Eyelevel Finder DA 2 Action Finder DW 3 Waist Level Finder and
20. heavy lines in Section C demonstrates a metering range for full aperture method using an f 1 4 lens and ASA TSO 100 film e Stop down metering Example ASA ISO film speed 100 Stopped down aperture f 8 In practice you will find that it is generally the high end and the low end which require a careful check The EV range of the Nikon F3 High Eyepoint camera encompasses most lighting situations and it is only under dim light or extra bright picture taking situations that you need pay any special attention EV Chart This EV Chart indicates the performance of the F3 High Eyepoint camera under normal temperatures and gives the usable ranges for all shutter speed film speed combinations rrim 5 Ennlan Yodo ipade ITP ee d a IET STP ke a BIL 1 i ke im pitti ets ES ae al FM Merapi Drala dios SB ER i EA ACCESSORIES Fig 2 BE 2 DA DW DW 4 In addition to the DE 3 High Eyepoint Finder the F3 High Eyepoint camera accepts various other interchangeable viewfinders To remove the finder slide the finder release levers Gh with your thumb and finger towards the back of the camera Fig 1 and lift the finder out Fig 2 The DX 1 AF Finder provides an electronic focus aid indication as you manually rotate the lens to obtain correct focus DX I Interchangeable viewfinders The DE 2 Eyelevel Finder offers regular eyelevel viewing and is recommended for photographers who don t wea
21. ible lens apertures have been tried then the available light is too bright or too dim for the meter s range Use either artificial light to increase the subject s brightness or a neutral density filter to reduce the amount of light reaching the film 21 Advance the film Stroke the film advance lever to transport the film to the next frame and get the camera ready for the next shot 22 Push in the rewind button is MLSA After the last exposure has been made the film advance lever will stop working You must then rewind the exposed film back into its cartridge To do this first turn the camera upside down and depress the rewind button to disengage the film sprocket drive 23 Rewind the film Lift the film rewind crank and turn it in the direction of the arrow to rewind the film When you feel the tension lessen continue winding one or two more turns until the film leader is rewound completely back into the cartridge 24 Remove the film cartridge Open the camera back and take out the film cartridge Avoid unloading the film in direct sunlight If there is no shade available turn your back on the sun and use your own shadow to shield the camera while unloading film 25 Turn the camera off To conserve battery power between takes return the power switch to the off position CONTROLS IN DETAIL In addition to automatic stepless shutter speed control the Nikon F3 offers manual control of all shutter spee
22. iece Adapter DK 1 The DK 1 is required when either the DR 3 Right Angle Viewing Attachment the DG 2 Eyepiece Magnifier or an Eyepiece Correction Lens designed for the F3 but not the F3 High Eyepoint camera is attached to the Nikon F3 High Eyepoint camera s viewfinder eyepiece Note that slight vignetting may occur when you wear glasses and look through the viewfinder with a correction lens for the F3 attached via the DK 1 Camera Cases The CF 21 CF 21A CF 22 Semi Soft Leather Cases and CS 15 Soft Leather Case were designed exclusively for the F3 High Eyepoint camera TIPS ON CAMERA CARE Camera care is common sense care Treat your F3 High Eyepoint camera as you would treat other valuable precision instruments Even though the F3 High Eyepoint camera is built to take many years of hard use it may be damaged by shock heat water or misuse Following are some tips to help you keep your camera in good condition 1 Keep the lens clean Keep the lens surfaces free of fingerprints and dust as much as possible Remove dust with a blower brush or lens tissue Never use cloth or ordinary tissue If smudges or fingerprints persist use lens tissue moistened sparingly with alcohol or lens cleaner Caution Use of a spray gun type blower to clean the lens may cause possible damage to the glass especially when ED glass is used for the front lens element by suddenly lowering the temperature on the lens surface To avoid damage hold the glow
23. image appears sharp The split image rangefinder works well for subjects having definite lines or boundaries The microprism collar is for fast moving subjects or ones with indistinct lines while the matte outer field is suitable for close ups In fast moving or candid shooting situations you can measure or estimate the distance between you and the subject and preset it on the lens using the distance scale ag engraved both in feet and meters Inside the viewfinder 1 LCD exposure information 2 ADR f number 3 Fine matte Fresnel outer field 4 Microprism collar 5 Split image rangefinder spot 6 12mm reference circle Note The meter reads the light over the entire focusing screen but is distinctly biased toward the central 12mm area 19 Set the lens aperture Turn the lens aperture ring ag until the desired f number is opposite the index mark on the lens The selected p g ed pp f number appears in the viewfinder for convenient reference 20 Take the picture Look through the viewfinder and press the shutter release button lightly to turn on the exposure meter The shutter speed display indicates the shutter speed selected by the camera As long as neither 2000 nor 8 appears in the shutter speed display the camera gives the correct exposure If either indication appears adjust the aperture ring on the lens until a desirable shutter speed is indicated Should either indication appear even after all poss
24. kwise until it comes off 8 Open the camera back Push the camera back lock lever 47 to the right with your thumb while lifting the film rewind knob 4g The oh ra E camera back will pop open 9 Install the film cartridge Drop the film cartridge into the film cartridge chamber so that the film leader points towards the takeup spool and push the rewind knob back down into place 10 Insert the film leader in the takeup spool Pull the leader across the camera and insert it into one of the slots in the film takeup spool Note The two data back contacts located inside the camera below the film guide rails are for use with a data back available in the future 11 Wind the film advance lever ey to advance film onto the takeup sprocket Wind the film advance lever and depress the shutter release button until the film sprockets engage the perforations on the edges of the film 12 Close the camera back Close the camera back until it snaps shut 13 Take up the film slack Fold out the film rewind crank an and rotate it in the direction of the arrow until it stops Then fold the crank back in 14 Make blank exposure until the frame counter a shows 1 Continue to wind the film advance lever and depress the shutter release button until the frame counter shows 1 While making blank exposures watch the rewind knob to see that it rotates This indicates that the film has been loaded correct
25. ly and is being advanced 15 Set the ASA film speed Lift up the ASA film speed dial a5 and rotate it in either direction until the white dot is opposite the ASA film speed in use Also make sure the exposure compensation dial is set to the red 0 This programs the camera s exposure meter so that it may provide a proper exposure for the type of film being used 16 Set the camera for automatic operation Rotate the shutter speed dial 7 until the A is opposite the white dot gg The built in locking mechanism PL az ensures that the dial cannot be accidentally shifted from the auto position during shooting 17 Hold the camera steady Wrap the fingers of your right hand around the camera body so that the index finger rests comfortably on the shutter release button and the thumb fits between the body and film advance lever Then cradle the camera in the left hand with the thumb and fingers grasping the lens locusing ring ag The Sar camera may be switched from horizontal to vertical format shooting in this position In focus 18 Focus on the subject Turn the lens focusing ring until the image in the viewfinder becomes sharp The K focusing screen comes with the camera as standard equipment With the split image rangefinder turn the ring until the split image becomes whole With the microprism grid turn the ring until the shimmering image appears sharp With the matte outer field turn the rinq until thc
26. mbination of Type A and J screens Matte Fresnel field with 3mm split image rangefinder spot surrounded by I1mm wide microprism doughnut Rapid and accurate focusing for subjects with both straight lines and ill defined contours Suitable for general photography Type L Same as Type A screen but with split image rangefinder line at a 45 angle Best for subjects with horizontal lines Type M Fine ground Fresnel field with 5 5mm clear spot and double cross hair for use in parallax focusing on aerial image plus millimeter scales for calculation of individual magnification of objects or for measuring objects Brilliant image in dim light Suitable for close ups photomicrography and other high magnification applications Type P Same as Type K but with split image rangefinder line at a 45 angle and etched horizontal and vertical lines as an aid to compositon Rapid and accurate focusing for subject with horizontal or vertical lines or ill defined contours Suitable for general photography Type R Same as Type A but with rangefinder prisms of sloping surfaces at a smaller angle and horizontal area vertical lines to aid proper composition Works best with lenses having maximum apertures from f 3 5 to f 5 6 Type T Matte Fresnel field with spit image rangefinder 12mm reference circle and horizontal and vertical lines Used when preparing slides for TV broadcasts Dotted lines indicate standard TV screen format Solid outline sh
27. nce lever Shutter speed scale Shutter speed dial Film plane indicator TABLE OF CONTENTS 2 3 FOREWORD 5 BASIC OPERATION 6 16 CONTROLS IN DETAIL 17 31 Shutter speed dial 17 19 Exposure memory lock button 20 Exposure compensation dial 21 ASA film speed dial 21 Memo holder 22 Shutter release button 22 Film advance lever 23 Frame counter 23 Multiple exposure lever 24 Batteries 24 Backup mechanical release lever 25 Depth of field preview button 25 26 Meter coupling lever 27 Mirror lockup lever 28 Self timer 28 Eyepiece shutter lever 29 Accessory shoe 29 Sync terminal 30 Viewfinder illuminator 30 Film plane indicator 31 Infrared focusing index 31 ABOUT THE LIQUID CRYSTAL DISPLAY LCD 32 EV RANGE OF THE CAMERA 33 35 ACCESSORIES 36 41 Interchangeable viewfinders 36 Interchangeable focusing screens 37 Focusing screen selector guide 38 Motor Drive MD 4 39 Speedlights 40 Other accessories 41 TIPS ON CAMERA CARE 42 43 SPECIFICATIONS 44 45 IMPORTANT 46 FOREWORD Congratulations You now own one of the most advanced and easy to use cameras on the market today With a wealth of exciting new features the Nikon F3 is designed to be as up to date as you are in your approach to photography However before actually taking pictures with the F3 you should familiarize yourself with its basic operation as presented in the first section For more detailed explanations and special picture taking situations refer to the
28. ows sale action area whereas broken lines indicate safe title area Type U Matte Fresnel field with 3mm fine ground matte focusing spot and 12mm reference circle Utilizes the same matte field as Type B but with lenses longer than 100mm the image in the viewfinder is easier to see With shorter focal length lenses this screen is nof suitable because of light fall off in the corners F3 High Eyepoint with MD 4 MF 4 Motor Drive MD 4 One of the most exciting accessories for the F3 High Eyepoint camera is the Motor Drive MD 4 This amazingly compact light and streamlined unit attaches to the bottom of the camera in seconds and advances the film either singly or in sequence up to 6 frames per second making it the fastest regular production motor drive on the market today Actual controls have been reduced to only those necessary for convenient operation In addition to the electromagnetic trigger button which also turns on the camera s meter when depressed halfway there are its concentric S C Single Continuous mode selector a battery check button and LED indicators two interlocking rewind slides for automatic film rewinding and a subtractive frame counter which stops the motor at the desired number of frames Eight AA type penlight batteries fit into a quick release clip housed in the base of the motor drive An optional NiCd battery pack is available for use in cold weather or when you want the fastest possible firing r
29. r glasses The DW 3 Waist Level Finder is ideal when you want to use the camera at a low angle or upside down over your head for shooting over crowds The DA 2 Action Finder works well for those situations when you can t bring your eye close to the finder such as when you are wearing a helmet or goggles or when the camera is enclosed in a waterproof underwater housing The DW 4 6X Magnification Finder is for critical high magnification close up work or photomicrography Regardless of which finder is attached you still have full automatic exposure control because the meter is built not into the finder but the body When using the DA 2 or DW 3 be careful that stray light does not enter from the top and cause an inflated meter reading Caution Before attaching the DX 1 the focusing screen inside the comera body must be removed refer to the next poge Fig 2 Interchangeable focusing screens Nikon offers you a choice of 21 interchangeable focusing screens A U The type K screen comes with the camera as standard equipment On the following page is a chart listing all the screens To take out the focusing screen first remove the finder then insert your fingernail under the rear edge of the screen and lift it out Fig 1 To install another screen simply insert the front edge the edge with the slot in the middle under the pin and push the rear edge of the screen down into place Fig 2 Note For more information on which screens are
30. release button 3 Watch the blinking red LED n a on the front of the camera The LED blinks faster during the final two seconds before the shutter opens to warn you to get ready 4 Don t forget to return the selt timer to its oriqinal position after using it If you want to cancel the self timer after pushing the shutter release button return the selftimer lever to its original position The picture then will not be taken Eyepiece shutter lever a When it s impossible to keep your eye at tho viewfinder such as when utilizing the self timer you should use the eyepiece shutter This shutter prevents stray light from entering the eyepiece and adversely affecting the automatic exposure meter reading Just push the lever to the left to close the shutter As a visual reminder that it s in use the blind is painted red Accessory shoe ag Located at the base of the rewind knob Lhe accessory shoe allows direct mounting of the Nikon SB 12 SB 16A SB 17 or SB 21A Speedlight Three electrical contacts as provide for synchronization of the flash unit automatic through the lens flash output control and ready light indication in the camera s viewfinder via an LED plus auto switching to the proper synchronization speed of 1 80 sec Three Nikon Flash Unit Couplers are available allowing either ISO or Nikon F2 type direct mounting electronic flash units to be attached Caution 1 For flash photography it is recommended that
31. rth Stop action Subject motion blur Exposure memory lock button 7 gt nae When there is a substantial difference between the main subject and the background unimportant bright spots or dark spots are likely to fool the camera s metering resulting in under or overexposure see Fig 1 One way to make exposure compensation is to use the memory lock This control allows you to lock in an exposure reading with the camera on automatic control To compensate for an excessively bright or dark background center the main subject in the viewfinder or move in close to the subject depress the memory lock button and hold it in then recompose and shoot see Fig 2 on 5 6 io Exposure compensation dial 7i Ma Another way to correct exposure is to use this dial Push the locking button E while rotating the dial The dial is graduated in one third stop increments 1 and 2 indicate one and two stops underexposure whereas 1 and 2 indicate one and two stops overexposure At ASA 6400 the compensation extends to only 1 at ASA 12 up to 1 The following table indicates the recommended settings for various subjects After use make sure you set the dial back to 0 Photographs and pictures with continuous Compensation not necessary gradation Copy work Approx 1 to 2 stops for black letters on Documents and drawings of high contrast white background approx 1 2 to 1 stop for white letters on black b
32. shutter button must be depressed halfway prior ro using the illuminator Otherwise it will not light up Film plane indicator gg TD The film plane indicator is engraved in white on the top deck just behind the shutter speed dial It indicates the exact position of the film plane inside the camera Whenever it becomes necessary to measure the exact distance between the subject and film plane such as in macrophotography use the film plane indicator The distance between the film plane and the lens mounting flange e z is exactly 46 5mm Infrared focusing index When you shoot infrared film note that the plane of sharpest focus is slightly farther away than that in visible light photography As a rule of thumb you can compensate for this shift in focus by referring to the infrared compensation index in the form of either a red dot or a red line near the focusing index on the lens barrel Some lenses including the Reflex Nikkor do not need compensation After focusing the image sharply through the viewfinder check the focused distance and turn the focusing ring to the left until the red infrared compensation index lines up with the prefocused distance Be sure to shoot with the appropriate filter such as R60 etc In this photo the subject to camera distance is set at i ABOUT THE LIQUID CRYSTAL DISPLAY LCD 1 At high temperatures over approx 60 C the whole surface turns black so that the exposure information
33. the up position until the advance lever stroke is completed Depth of field preview button 9 This control allows you to get a visual impression of the various parts of the scene in front of and behind the main subject which will appear sharp in the final photograph see the photos on the next page To operate this control push the button while looking through the viewfinder If the lens is set to anything other than maximum aperture the image on the focusing screen will give you an indication of exactly what will be in focus in the final photo The image progressively gets darker as the lens aperture gets smaller rh Lens set at f 2 8 Lens set at f 16 At wide apertures the depth of field is very shallow with the main subject in focus But when the lens is stopped down to f 16 most objects from near to far are in sharp focus n L Meter coupling lever Push the meter coupling lever release button 20 and lock the meter coupling lever in the up position before mounting a non AI Nikkor lens Then perform stopped down metering in the following manner For non AI Nikkor lenses with automatic diaphragms On AUTO Push in and hold the depth of field preview button while you trip the shutter Caution If the depth of field preview button is not depressed all the way the mirror may remain in the up position On MANUAL Select a shutter speed Then hold in the preview button and turn the aperture ring until the
34. tter will remain locked open Multiple exposure lever R By Double or multiple exposures are easy to accomplish with the F3 s multiple exposure lever Follow this procedure 1 Take the first shot 2 Then to recock the shutter without advancing the film push the multiple exposure lever forward Fig 1 and stroke the advance lever Immediately the multiple exposure lever will spring back to its normal position Fig 2 3 Now you re ready to take the second shot on the same frame For more than two shots on the same frame just repeat the same procedure for each additional exposure When you ve finished simply advance the film normally to the next frame Note While making multiple exposurea the frame counter doesn t advance Batteries When battery power fails the camera s exposure meter stops working and the shutter won t work either unless you use the backup mechanical release lever For this reason it is a good idea to carry an extra set of batteries with you whenever you set out to take pictures Under normal usage one set of 1 5V silver oxide batteries Eveready EPX76 or equivalent will last for about one year Try not to touch the or surfaces of the batteries as this many result in poor electrical contact If you do get fingerprints on the battery terminals wipe them off with a soft cloth At below freezing temperatures battery performance deteriorates The use of a fresh set of batteries is recommended to ens
35. ure reliable service at low temperatures In extremely cold climates it is recommended to use the F3 in conjunction with the MD 4 Motor Drive With the motor drive attached the camera gets all its power from the batteries in the motor drive Thus if you use a NiCd battery the camera motor drive will operate down to 20 C Note At 10 C or below the LCD may exhibit a slight delay in response time This is natural and should be no cause for concern However exposure to extremely high temperatures 80 C and above may actually shorten the life of the LCD Backup mechanical release lever i This lever is provided as an alternative method of tripping the shutter in case the camera s batteries become weak or completely exhausted To operate the lever first use your fingernail to pull it down to the ready position Then push it down to trip the shutter The shutter operates at a mechanical speed of approx 1 60 sec regardless of the setting on the shutter speed dial Even when the batteries are exhausted you can still make time exposures by setting the dial to T and using the backup mechanical release lever to trip the shutter Caution If you advance the film while holding down the backup mechanical release lever the shutter will fire immediately at the completion of the film advance stroke thus wasting a frame Also if you fail to advance the film completely and then use this lever to trip the shutter the mirror i Y will remain in
Download Pdf Manuals
Related Search
camera Manual(1)(2)