Home

PHILIPS Xalio 300 user manual

1. PROBLEMS No dialling tone when ing AS pressing NN Troubleshooting CAUSES The base station is not properly connected to electricity or to the telephone sockets Too far from the base station Battery pack is low low battery icon is displayed SOLUTIONS Check the connections p 4 Reset the product by unplugging the power cord for few seconds and then by connecting it again Move closer to the base Charge battery pack for at least 24 hours page 4 icon is blinking The handset is out of range Move closer to the base station When the handset is placed on the charging unit no beep is heard The handset is not placed correctly on the base station charging unit Charging contacts are dirty Take the handset off the base station and put it back again Clean them with a clean and dry cloth Battery icon remains empty although the handset has charged for 24 hours No symbol on the display Bad audio guality crackles muted echo etc The Caller Line Identification does not work Handset battery pack is defective Battery pack is uncharged Interference from nearby electrical appliance Base station installed in a room with thick walls You are using the handset too far from the base station Service not activated or wrong operator or wrong setting Please contact your PHILIPS dealer in order to pur
2. lio Xe 3090 Xalio 300 Xalio 300 Multihandset packs Charge handset s for 24 hours before use This equipment is not designed for making emergency telephone calls when the power fails Earpiece Phonebook Star Programming key Microphone Xalio 300 Handset Display Line key PHILIPS 1I3320CC WENT ITD IO YU ZO Correction Redial amp Call log key e Hash Transfer amp JI Be o Xalio 300 multihandset packs Handset display The display gives information about the operation of your telephone ed a A On first use it is sometimes necessary to wait for a few minutes of charge before seing icons on the display The meaning of the icons is the following OA The battery is currently charging iN The battery is full i The battery is low Please charge The handset receives an incoming call C There is a call in progress Y The handset is within range of the base station Yo The handset is out of range Move closer to the base station D The Xalio 300 is in programming mode A programming operation is in progress NA AME The network has sent a message notification x 7 A call transfer is in progress 7 iN vU Phonebook 0
3. perturbations and for radio spectrum Installing the Xalio 300 PLEASE CHARGE THE XALIO 300 FOR 24 HOURS BEFORE USE ONLY USE RECHARGEABLE BATTERY PACK Unpacking your Xalio 300 The Xalio 300 package contains One Xalio 300 base station If anything is missing please contact your place of purchase immediately In the Xalio 300 multihandset packs you will also find one or more additional handsets chargers with their power supply and additional NiMH AAA 600 x 2 rechargeable battery packs Configuring your Xalio 300 Don t change your configuration code if you live in UK or Northern Ireland Your product is already factory configured with the right settings Country Code UK dial 44 Northern Ireland dial 44 Warning If you live in the Republic of Ireland you must enter the relevant configuration code using the key sequence shown followed by your country code Rep of Ireland dial 153 Advice lf you have bought your product in any of the above countries but want to use it in another one you can enter the configuration code according to the above tables in order to activate the right country settings Nevertheless you have to change the telephone line cord adapter according to the country where you want to use it Installing your Xalio 300 Qo Plug the power supply unit into the wall socket m cord into the wall socket 2 Plug the telephone line gt 9 Open the battery do
4. an choose several types according to your country The numeric display on your Xalio 300 does not show the name of the caller Press the Programming key Press the 0 key Select I 2 3 Press the Programming key to confirm your setting To select the recall type key R setting country dependent The use of some services accessed with RFI R 2 and R 3 call waiting call forward will depend on the flash setting short long according to your installation type ISDN Public PABX Press the Programming key Press the 5 key Select or 2 Press the Programming key country dependent In some countries you may have only one default setting available 9 To select tone dialling country dependent Press the Programming key Press the Star key Press the Programming key to confirm your setting To select pulse dialling country dependent This allows you to select pulse dialling also called Loop disconnect and used in countries without DTMF tone dialling capability or using old PABX Press the Programming key Press the Hash key Press the Programming key To clear the network message notification M Use this function if the network does not clear the message notification after reading See note page l Press the Programming key Press the 4 key Press the Programming key country dependent In some countries you may have only one default setting available
5. chase new rechargeable battery pack Make sure your product is plugged in p 4 Charge battery pack p 4 Try to plug the base station in elsewhere Install the base station in a different room Move closer to the base station Reduce the volume level p 8 Check your subscription with network or change caller identification type see p 9 Philips cannot guarantee the operation behind an ISDN adpater or a PABX The telephone rings while on line Note 4 The screen can display An attempt to transfer a call is in progress an unidentified call unlisted numbers withheld caller identification Press the line key to take the line if appropriate Note For more information on this function contact your operator Available also subject to technical availability Note 2 If Caller Display type does not work try another type 1 2 3 Note 3 Philips has designed the Xalio 300 to work on a PSTN analogue line Use on an ISDN line with an adapter is not guaranteed if non recognised number Environment and Safety Safety information The Xalio 300 is not designed for making emergency calls when the power fails An alternative should be made available for making emergency calls Power requirements The product requires an electrical supply of 220 240V alternating monophased current excluding IT installations defined in standard EN 60 950 WARNING The e
6. lectrical network is classified as dangerous according to criteria in the standard EN 60 950 The only way to power down the product is to unplug the power supply from the electrical outlet Ensure the electrical outlet is located close to the apparatus and is always easily accessible Telephone connections The voltage on the network is classified as TNV 3 Telecommunications Network Voltages as defined in the standard EN 60 950 Safety precautions Do not allow the handset to come into contact with liquids Do not open the handset or the base station This could expose you to high voltages Do not allow the charging contacts or the battery to come into contact with conductive materials Environmental care Please remember to observe the local regulations regarding the disposal of your packaging materials exhausted batteries and old phones and where possible promote their recycling Conformity We Philips declare that the product Xalio 300 is in compliance with ANNEX lll of the R amp TTE Directive 1999 5 EC and then with the following essential requirements Article 3 1 a protection of the health amp the safety of the user EN 60950 2000 Article 3 1 b protection requirements with respect to electromagnetic compatibility ETSI EN 301 489 6 VI 1 1 09 200 amp ETSI EN 301 489 1 VI 3 1 09 2001 Article 3 2 effective use of the radio spectrum EN 301 406 2001 The presumption of conformity with the essential requirement
7. or on the handset by sliding it down o Connect the battery pack to the connector inside the handset Place the battery with sticker face up and wires along the left side of the battery pack A When replacing the battery only use NiMH Optimal battery life is reached after 3 cycles of full charge discharge Standby time around 300 hours NV Talk time around 18 hours 6 Replace the battery door 0 Put the handset on the base and charge for 24 hours before use Using the Xalio 300 Note When using your telephone 3 different beep types can be heard J a validation beep JJ an error beep JJ a programming invitation beep JI long press to come back on idle mode at any time A To answer a Call Press the Line key to answer the call To end a call Press the Line key Or Replace the handset on the base To make a call Press the Line key Dial the number Predialling First dial the phone number If you make a mistake press the Correction key to delete incorrect digits Press the Line key To store an entry in the phonebooks Press the Phonebook key once to open Phonebook or press the Phonebook key twice to open Phonebook 2 Enter the memory number 0 to 9 you want to give to this entry Press the Programming key Enter the telephone number you want to store up to 16 digits including a pause by pres
8. s regarding Council Directive 1999 5 EC is ensured Date 06 01 2003 bb Vice president amp General manager DECT amp Home Telephony The product can only be connected to the analogue telephone network in the countries indicated on the back cover of this manual 2003 Philips Consumer Electronics DECT amp Home Telephony All rights reserved Printed in France www philips com CE S5 IRL 3111 285 20631
9. sing the Transfer key If you make a mistake press the Correction key to delete incorrect digits Press the Programming key to confirm your setting To make a call from the phonebooks Press the Phonebook key once to open Phonebook or press the Phonebook key twice to open Phonebook 2 Enter the memory number Display shows the corresponding number Press the Line key to call To view the phonebooks entries Press the Phonebook key once to open Phonebook or press the Phonebook key twice to open Phonebook 2 Enter the memory number Display shows the corresponding number Press the Phonebook key to exit A Modify a number by pressing the Correction key press it again to erase digits Press Programming key to validate S NJ To delete an entry Press the Phonebook key once to open Phonebook or press the Phonebook key twice to open Phonebook 2 Enter the memory number you want to delete Press the Programming key twice To call the last number Redial Press the Redial key Display shows the last number called Press the Line key To call back the last five callers To use the call log function you must first subscribe to the Caller Line Identification CLI Service See note page 11 Press the Redial key twice Display shows the last number received see note 4 page 11 Use the keys I and 3 to navigate within the call log Press the 2 key if you want to know the date and ho
10. to 9 memories consultation or editing in progress NI Phonebook 2 0 to 9 memories consultation or editing in progress NI 5 New entry on call log Z7IN Zr Call log consultation Contents Xalio 300 handset Troubleshooting ll Handset display Notes II Installing the Xalio 300 3 Environment amp Safety 12 Using the Xalio 300 5 To answer a call 5 To end a call 5 To make an external call 5 Predialling 5 To store an entry in the phonebook To make a call from the phonebook To view the phonebook entries To delete an entry To call the last number Redial Philips has marked the Battery To call back the last five callers and packaging with standard symbols designed to promote the recycling and To transfer a call to another appropriate disposal of your eventual Os handset Xalio 300 multihandset Waste Ea M Batteries should not be disposed of Programming the Xalio 300 with general household waste To set the ringer melody e A financial contribution has been paid To set the ringer volume to the associated national recovery amp To change the earpiece volume recycling system To select Caller Display type To select the recall type Key R setting 9 The CC marking certifies To select tone dialling 10 compliance with technical regulations in To select pulse dialling 10 accordance with the Directive 1999 5 EC To clear the network message for the safety of the user electromagnetic notification 10
11. ur of the call Press the 6 key if you want to erase the entry or Press the Line key to make the call To transfer a call to another handset Xalio 300 multihandset pack You can forward an external call to another handset During a call Press the Transfer key All handsets will ring Press the Line key on one of the other handset to take the transfered call A If you have only one handset pressing the Transfer key will also make your handset ring Programming the Xalio 300 To set the ringer melody You can choose from 7 ringer melodies Press the Programming key Press the I key Enter your choice of melody 2 or 7 The selected melody is played Press the Programming key to confirm your setting To set the ringer volume You can choose from 3 ringer volumes Press the Programming key Press the 2 key Enter your choice of volume I low 2 medium or 3 high The melody is played at the selected volume Press the Programming key to confirm your setting To change the earpiece volume You can choose from 3 earpiece volume levels Press the Programming key Press the 3 key Enter your choice of volume I low 2 medium or 3 high Press the Programming key to confirm your setting To select Caller Display Type country dependent To use the Caller Display function you must first subscribe to the Service from your Network operator See Note 1 2 and 3 page l1 You c

PHILIPS Xalio 300 user manual

Contents

Download Pdf Manuals

Related Search

Related Contents