3M Thermally Conductive Grease TCG-2037 TCG-2033
Contents
1. Information relates to the 3M Grease TCG 2033 3M Thermally Conductive Grease TCG 2037 TCG 2033 Typical Performance Characteristics Note The following technical information and data should be considered representative or typical only and should not be used for specification purposes k 3 0 W m K Thermal Impedance 0 017 C in2 W 0 109 C cm W Thermal Impedance measured with a modified 3M ASTM D5470 Test Method Storage and Shelf Life Product Shelf life is 9 months from date of manufacture when stored in the original product container and packaging materials and stored at room temperature 18 24 C and 50 RH To ensure best uniformity of conductive fillers the product should be mixed prior to use to ensure uniform distribution of fillers Directions for Use Apply the product at the desired interface and use pressure from approximately 1 25 psi applied at a variable or constant force as determined by end user when bringing the substrate interfaces together Pressure is applied until the desired gap thickness is achieved Apply sufficient product to ensure good gap filling at the desired final nominal gap thickness Sufficient product volume use can be demonstrated by having a small amount of squeeze out at the edges of the interface Heat can be applied 40 50 C to lower the product viscosity to aid in product flow and for establishing a desired gap thickness The 3M Thermally Conductive Grease TCG 2033 product c2. Technical Data December 2008 3M Thermally Conductive Grease TCG 2037 TCG 2033 Product Description 3M Thermally Conductive Grease TCG 2037 is a high performance thermal interface material for transferring thermal energy from a heat source e g processor chip graphics chip etc to a heat sinking or heat spreading surface The 3M Grease TCG 2037 s blend of inorganic fillers in a non silicone resin system provides for excellent bulk thermal conductivity along with very low thermal resistance 3M Thermally Conductive Grease TCG 2033 has a lower viscosity versus the 3M Thermally Conductive Grease TCG 2037 as a small amount of solvent has been blended into the product The lower viscosity of the 3M Grease TCG 2033 can allow for a thinner bond line leading to improved thermal resistance and is also designed for use in screen printing applications Key Features e Superior bulk conductivity e Non silicone based formulation e Excellent thermal impedance e lt 40 u max particle diameter e 3M Grease TCG 2033 is screen printable Typical Physical Properties Note The following technical information and data should be considered representative or typical only and should not be used for specification purposes G 1450 Pa 25 C 360 Pa G 375 Pa 25 C 210 Pa n 20 Pa sec 25 C 5 Pa sec 5 2 5 g cm 2 43 Vol Resistivity 4 10 x 107 O cm 1 kHz Dielectric Breakdown Strength 105 Volts mm
3. contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon in writing by an authorized officer of 3M Warranty Limited Remedy Limited Liability This product will be free from defects in material and manufacture at the time of purchase 3M MAKES NO OTHER WARRANTIES INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE If this product is defective within the warranty period stated above your exclusive remedy shall be at 3M s option to replace or repair the 3M product or refund the purchase price of the 3M product Except where prohibited by law 3M will not be liable for any indirect special incidental or consequential loss or damage arising from this 3M product regardless of the legal theory asserted These products are not warranted or guaranteed to be silicone free Electronics Markets Materials Division 3M Electronics 3M Center Building 21 1W 10 900 Bush Avenue St Paul MN 55144 1000 3M is a trademark of 3M Company 1 800 251 8634 phone Please recycle Printed in U S A 651 778 4244 fax 3M 2008 All rights reserved www 3M com electronics 60 5002 0366 0 3
4. ontains a small amount of solvent to lower viscosity and allow for screen printing Screen print to a desired surface and allow product to rest open faced for 2 10 minutes at room temperature to allow solvent to evaporate prior to assembly Review MSDS for detailed use information 2 3M Thermally Conductive Grease TCG 2037 TCG 2033 Precautionary Information Refer to Product Label and Material Safety Data Sheet for Health and Safety Information before using this product For additional health and safety information call 1 800 364 3577 or 651 737 6501 For Additional Information To request additional product information or to arrange for sales assistance call toll free 1 800 251 8634 Address correspondence to 3M Electronics Markets Materials Division Building 21 1W 10 900 Bush Avenue St Paul MN 55144 1000 Our fax number is 651 778 4244 or 1 877 369 2923 In Canada phone 1 800 364 3577 In Puerto Rico phone 1 787 750 3000 In Mexico phone 52 70 04 00 Important Notice All statements technical information and recommendations related to 3M s products are based on information believed to be reliable but the accuracy or completeness is not guaranteed Before using this product you must evaluate it and determine if it is suitable for your intended application You assume all risks and liability associated with such use Any statements related to the product which are not contained in 3M s current publications or any
Download Pdf Manuals
Related Search
3M Thermally Conductive Grease TCG 2037 TCG 2033