Foxconn 6497MB series motherboard English user manual V1.0
Contents
1. Select this option and press lt Enter gt and a dialogue box will pop up to let you load the optimized BIOS default settings Select lt Y gt and then press lt Enter gt to load the optimized defaults Select lt N gt and press lt Enter gt to exit without loading The defaults set by BIOS are the optimized performance parameters for the system to improve the performance of your system components However if the optimized performance parameters are not supported by your hardware devices it will likely cause system reliability and stability issues If you only want to load the optimized default for a specific option select the desired option and press the lt F gt key Set Supervisor User Password The access rights and permissions associated with the Supervisor password are higher than those of a regular User password The Supervisor password can be used to start the system or modify the CMOS settings By default the option Set User Password is displayed in gray and can be activated only when users assign the Supervisor password The User password can also start the system While the User password can be used to view the current CMOS settings these settings cannot be modified using the User password When you select the Set Supervisor User Password option the following message will appear in the center of the screen which will help you to set the password Enter Password Enter your password not exceeding 8 characters the2. CPU Clock Ratio Default based on CPU specifications This option is used to set the ratio of an unlocked CPU The possible settings range from a minimum of 0 to a maximum of 50 Note This option is invisible for locking frequency CPU lt Auto Detect DIMM PCI Clk Default Enabled This option is used to set whether the clock of an unused DIMM PCI slot will be disabled to reduce electromagnetic interference The available settings are Enabled and Disabled lt Spread Spectrum Default Disabled When enabled it can significantly reduce the EMI Electromagnetic Interference generated by the system al Warning Be sure your selection is right CPU overclock will be dangerous We will not be responsible for any damage caused FOXCONN Chapter 3 BIOS Description Load Fail Safe Defaults Press lt Enter gt to select this option A dialogue box will pop up that allows you to load the default BIOS settings Select lt Y gt and then press lt Enter gt to load the defaults Select lt N gt and press lt Enter gt to exit without loading The defaults set by BIOS set the basic system functions in order to ensure system stability But if your computer cannot POST properly you should load the fail safe defaults to restore the original settings Then carry out failure testing If you only want to load the defaults for a single option you can select the desired option and press the lt F6 gt key Load Optimized Defaults
3. j feseerces LPress Eater PELCGGR Palette Sanap Hare cen Boe s epparted Nee reen Paplead Sure Siete iHome Fetler Selert f Pus PE F la FDI Sa RI Exe i L SES PEETA l ER lp F5 dd ZER OTT F Farl SaFe d Biect 3 Berk mm GE BeFamli s PnP PCI Configurations Menu Init Display First Default PCI Slot This item is used to set which display device will be used first when your PC starts up The available setting values are PCI Slot and PCIEx lt Reset Configuration Data Default Disabled This option is used to set whether the system is permitted to automatically distribute IRQ DMA and I O addresses when each time the machine is turned on The setting values are Disabled and Enabled lt Resources Controlled By Default Auto ESCD This option is used to define the system resource control scheme If all cards you use support PNP then select Auto ESCD and the BIOS will automatically distributes interruption resources If the ISA cards you installed not support ing PNP you will need to select Manual and manually adjust interruption resources in the event of hardware conflicts However since this motherboard has no ISA slot this option does not apply lt PCI VGA Palette Snoop Default Disabled If you use a non standard VGA card use this option to solve graphic accelera tion card or MPEG audio card problems e g colors not accurately displayed The setting values are Disabled and Enabled
4. on the rear panel will not work If you do not want to use the Front Audio pin 5 and 6 pin9 and 10 must be SHORT and then the sig nal will be sent to the rear audio port USB Connectors F_USB1 F_USB2 Besides four USB ports on the rear panel the series of motherboards also have two 10 pin connectors on board which may connect to front panel USB cable optional to provide additional four USB ports VCC VCC VCC VCC D5 D4 D7 D6 D5 D4 D7 D6 GND GND GND GND Empty NC Empty NC F_USB 1 F USB 2 Additional COM Connector COM2 This motherboard provides an additional serial COM connector for your machine Connect one side of a switching cable to the connector then attach the serial COM device to the other side of the cable FOXCONN Chapter2 Installation Instructions 1394 Connector F_1394 optional The 1394 expansion cable can be connected to either the front provided that the front panel of your chassis is equipped with the appropriate interface or rear TPB panel of the chassis 12V GND IrDA Connector IR This connector supports wireless transmitting and re Empty ceiving device Before using this function configure the settings of IR Mode from the Integrated Peripherals section of the CMOS Setup 5V IRTX Chassis Intruder Connector INTRUDER The connector connects to the chassis security switch on the case The system can detect the chassis intrusion through the status of this connecto
5. 100M Ethernet LAN is enabled The available setting values are Disabled and Auto SIS MAC Address Input optional When Machine MAC Address is set as Enabled you can select the option and key in MAC address lt Onboard LAN Controller Default Enabled optional This option is used to set whether the onboard 1000M LAN controller is enabled The available setting values are Disabled and Enabled lt Onboard LAN Boot ROM Default Disabled This option is used to decide whether to invoke the boot ROM of the onboard LAN chip The available setting values are Disabled and Enabled FOXCONN Chapter 3 BIOS Description Fhoreiz eebe e E IERCH ekbanrd Sager lf Baas SEEE A e yet a E nak be lien Help Can Fee IFE Tae Ge g s God ial Fees i e 2 FR pol i RER e leet Ha J re Nap Fair G t Par ay Pork E Se Fark EP EGF As User ts SleetHoee 2 HTH ET ONE E ed Dia KR PR TI FOODS a Exit Flchesers L Hel FSS Frewppas lalprs F Faal SaFe Petan lis gt Mert weg zed Ch Fambis Onboard SuperlO Device Menu lt Onboard Serial Port 1 2 Default 3F8 IRQ4 2F8 IRQ3 This option is used to assign the I O address and interrupt request IRQ for the onboard serial port 1 2 Note Do not try to set the same values for serial ports 1 and 2 lt UART Mode Select Default Normal Use this option to select the UART mode Setting values include Normal IrDA ASKIR The setting value is determi
6. Always Off This option is used to control power resume state The available setting val ues are Always Off Always On and Keep Pre State PM Wake Up Events Press lt Enter gt to set the items of PM Wake Up Events Please refer to page 39 Foxconn Chapter 3 BIOS Description he at BS DEER Gas Miilits PE TEELS pemn ed Kat nth Led p E eabtedi TE EE Me teg iren GER HI Ze ra ria Mabe op from S19 S455 Clic reer Ma hn Elan ESA ed DisehDed NES HIR Primary CHE CKissbiet 5 I Bi Ded 1A L Pc Greg Ap Ch kiEre tle Pars Dater beck Wana oe HTL ESE Exit Fitieseral Be PES da CLC Waloes TE Fail Safe Defaults T F Be Faa lis PM Wake Up Events Menu RING Power Up Control Default Enabled If this option is enabled it allows the system to resume from a software power down or power saving mode whenever there is an incoming call to an in stalled fax modem This function needs to be supported by the relevant hard ware and software The setting values are Disabled and Enabled lt MACPME Power Up Control Default Enabled optional This option is used to enable or disable the system to be waken up by SIS onboard LAN lt PCIPME Power Up Control Default Enabled This option is used to enable or disable the system to be waken up by PCI card lt PS2KB Power Up Control Default Hot Key This option is used to set which action will wake up PS 2 keyboard from S3 S4 S5 statu
7. Configuration and Power Interface ACPI is a standard that defines power and configuration management interfaces be tween an operating system and the BIOS In other words it is a standard that describes how computer components work together to manage system hardware In order to use this function the ACPI specification must be sup ported by the OS for example Windows 2000 or WindowsXP The available setting values are Enabled and Disabled lt ACPI Suspend Type Default S1 POS This option is used to set the energy saving mode of the ACPI function When you select S1 POS mode the power will not shut off and the power supply status will remain as it is In S1 mode the computer can be resumed at any time When you select S3 STR mode the power will be cut off after a delay period The status of the computer before it enters STR will be saved in memory and the computer can quickly return to previous status when the STR function wakes When you select S1 amp S3 mode the system will automatically select the delay time lt Power Management Default User Define This option is used to set the power management scheme Available setting values are User Define Min Saving and Max Saving lt Suspend Mode Default Disabled This option is used to set the idle time before the system enters into sleep status The setting values are Disabled and 1 Min 1 Hour FOXCONN Chapter 3 BIOS Description Video O
8. FOXxconn Chapter3 BIOS Description PC Health Status Pheenax eh ID SE SS TL TE FE Bealth 5 EFE Werning Tenperatere Eiszsbbed GITT WR CH Enard Fan EE ler Pile Sart Te wd Ekari PIH lal dr 137 Supe Bales OPE 11 Seed On Temp Iw al tL isles SITT SCHT Mni R mM RT E OX Picieseral Be Lp ED Fes ans Kabes FE Fait Safe Defaults Bed ina zed Be Falis PC Health Status menu CPU Warning Temperature Default Disabled This option is used to set the warning temperature for the CPU When the temperature of CPU is higher than setting value the motherboard will send off warning information The setting values are Disabled and 50 C 122 F 53 C 127 F 56 C 133 F 60 C 140 F 63 C 145 F 66 C 151 F 70 C 158 F lt Case Open Warning Default Disabled This option is used to enable or disable case open warning function The setting values are Disabled and Enabled lt Smart Fan Controller Default Enabled This option is used to enable or disable smart fan function The setting values are Disabled and Enabled Foxconn Chapter 3 BIOS Description Frequency Voltage Control Pheemiz Fear dE MS ORE Sertap Btalaty Freqeeney Us tage Costrel ERR Clet Batis EA futa Bebect BIMASPE CIE Emad Ded Spread Spectren Disab bed Boe G Sfadee HTL ESEtExit Fitiemeral Bele F T TP tle ere Dater Sleet l T PES Ae DTD Maloers b Fail Safe Defaults ER TER TEE Frequency Voltage Control Menu
9. Onboard Audio 8 optional e Supports 8 channel audio e Supports SPDIF output e Supports high quality differential CD input PCI Express x16 Support e Supports A GB sec 8 GB sec concurrent bandwidth e Low power consumption and power management features Green Function e Supports ACPI Advanced Configuration and Power Interface Supports SO normal S1 power on suspend S3 Suspend to RAM GA Suspend to disk depends on OS and S5 soft off Expansion Slots e Three PCI slots e One PCI Express x16 Graphics slot FOXxconmMm Chapter 1 Product Introduction Advanced Features e PCI 2 3 specification compliant e Supports Windows 2000 XP soft off e Supports PC Health function capable of monitoring system voltage CPU temperature system temperature and fan speed Chapter 1 Product Introduction Geo e Si ee 8 e d 1 AUX_IN Connector optional 2 CD_IN Connector 3 4 pin ATX_12V Power Connector 4 CPU Fan Connector 5 LGA775 CPU Socket 6 North Bridge SiS649 SiS662 Chipset 7 South Bridge SiS964 Chipset 8 184 pin DIMM Slots 9 24 pin ATX Power Connector 10 IrDA Connector 11 Chassis Intruder Connector 12 BIOS Protection Jumper 13 FDD Connector e e o e o OO e 14 ATA 133 100 66 IDE Connectors 15 Serial ATA Connectors optional 16 Clear CMOS Jumper 17 System Fan Connector 18 Front Panel Connector 19 Speaker Connector 20 COM2 Connect
10. can be set up through this menu FOXCONN Chapter 3 BIOS Description BIOS Features The special features can be set up through this menu Advanced BIOS Features The advanced system features can be set up through this menu Advanced Chipset Features The values for the chipset can be changed through this menu and the sys tem performance can be optimized Integrated Peripherals Onboard peripherals can be set up through this menu Power Management Setup All the items of Green function features can be set up through this menu PnP PCI Configurations The system s PnP PCI settings and parameters can be modified through this menu PC Health Status This will display the current status of your PC Frequency Voltage Control Frequency and voltage settings can be adjusted through this menu Load Fail Safe Defaults The default BIOS settings can be loaded through this menu Load Optimized Defaults The optimal performance settings can be loaded through this menu however the stable default values may be affected Set Supervisor User Password The supervisor user password can be set up through this menu Save amp Exit Setup Save CMOS value settings to CMOS and exit setup Exit Without Saving Abandon all CMOS value changes and exit setup Foxconn Chapter 3 BIOS Description Standard CMOS Features This sub menu is used to set up the standard CMOS features such as the date time HDD model and so on Use the arrow
11. gt Cylinder number of cylinders number of heads write pre compensation Landing Zone FOXCONN Chapter 3 BIOS Description Award Phoenix BIOS can support 3 HDD modes CHS LBA and Large or Auto mode For HDD lt 528MB SSC For HDD gt 528MB amp supporting LBA Logical Block Addressing For HDD gt 528MB but not supporting LBA Recommended mode Drive A B This option allows you to select the kind of FDD to be installed including None S60K 5 25 in 1 2M 5 25 in 720K 3 5 in 1 44M 3 5 in and 2 88 M 3 5 in Video The following table is provided for your reference in setting the display mode for your system VGA SEGA SVGA or PGA monitor adapters Halt On This category determines whether or not the computer will stop if an error is detected during powering up will stop and you will be prompted No Errors The system boot will not stop for any error that may be detected All But Keyboard The system boot will not stop for a keyboard error but it will stop for all other errors stop for all other errors error but it will stop for all other errors Foxconn Chapter 3 BIOS Description Memory This is a Display Only Category determined by POST Power On Self Test of the BIOS Base Memory The BIOS POST will determine the amount of base or conventional memory installed in the system Extended Memory The BIOS determines how much extended memory is m present during the POST To
12. set the delay time between RAS Row Address Strobe and CAS Column Address Strobe signals The setting values are 2T 3T 4T 5T lt Precharge Time tRP Default Depend on memory It is used to set the precharge time of RAS The setting values are 2T 3T 4T 5T lt RAS to Active Time tRCD Default Depend on memory It is used to set the RAS to active time The setting values are 4T 15T lt Write Recovery Time tWR Default Depend on memory It is used to set the write recovery time The setting values are 1T 2T 3T AT 5T 6T lt DDR 128 Bit Access Default Disabled It is used to set whether 128 bit access is allowed or not Foxconn Chapter 3 BIOS Description Integrated Peripherals Pheenix eard llS CHES Setup Otality Bategrabed Peripherals t SIS fetihop IDE TE Fress Enter Jien Help IE Uoti D Wd ZEIT Freee Caer ee ee ee iraire Fress Enter KR reel PRG Eleck Hade es CHIC TZ LEDE Bas Ss Laberface EDE us Gccess laberface EDE Bas 2 08 eeess mberar LEDE Bus E ccess oterface EDE Bas later LEDE Bus a ea Poker ter deck d d Wa RER AT RITTER Il CTIa H Fictheseral rip P Frevuoes aloes Ehr Fail Safe Petanlge F3 Bpi maizi Befaeli Integrated Peripherals Menu SIS OnChip IDE Device Press the lt Enter gt key to enter the setup sub menu For details please refer to page 34 SIS OnChip IDE Device Press the lt Enter gt key to enter the setup sub menu For details p
13. the content of this manual will remain consistent with the actual BIOS version at any given time in the future OH Attention The pictures of objects used in this manual are just for your reference Please refer to the physical motherboard 6497MB Engl i sh pref ace p65 6 2005 5 9 15 18 6497MB Engl i sh pref ace p65 This manual is suitable for 6497MB motherboard Each motherboard is carefully designed for the PC user who wants diverse features L with onboard 100M LAN K with onbaord 1G LAN 6 with 6 channel audio 8 with 8 channel audio E with 1394 function S with SATA function R with RAID function You can find PPID label on the motherboard It indicates the functions that the motherboard has For example OM OOK COON ON OUNO 00 OUV OID UOO OUNI UN On the blue mark of the PPID label it means the motherboard supports 6 channel audio 6 1394 port E onboard 100M LAN L SATA function S 7 2005 5 9 15 18 Thank you for buying Foxconn s 6497MB series motherboard This series of motherboard is one of our new products and offers superior performance reliability and quality at a reason able price This motherboard adopts the advanced SiS649 SiS964 SiS964L chipset providing users a computer platform with a high integration compatibility performance price ratio This chapter includes the following information Main Features Motherboard Layout FOxCONN Chapter 1 P
14. to always con nect with the cable on the same side as pin 1 of the PIDE SIDE or FDD connector on the motherboard FOXCONN Chapter2 Installation Instructions Front Panel Connector FP1 This motherboard includes one connector for connect ing the front panel switch and LED indicators Sa IDE LED Connector IDE LEID The connector connects to the case s IDE indicator LED indicating the activity status of hard disks Reset Switch RESET Attach the connector to the Reset switch on the front panel of the case the system will restart when the switch is pressed Power LED Connector PLED Attach the connector to the power LED on the front panel of the case The Power LED indicates the system s status When the system is in SO status the LED is on When the system is in S1 status the LED is blink When the system is in S3 S4 S5 status the LED is off Power Switch Connector PWRBTN Attach the connector to the power button of the case Pushing this switch allows the system to be turned on and off rather than using the power supply button Fan Connectors CPU_FAN FAN The fan speed of CPU FAN and FAN1 can be detected and viewed in PC Health Status section of the CMOS Setup These fans will be automatically turned off after the system enters S3 S4 and S5 mode Plug the CPU cooling fan cable into the 3 pin CPU FAN power supply on the motherboard Connect the case cooling fan connector to FAN1 1 GND GND P
15. CMOS Setup but also to start up your PC Floreis beard DIS CHES Setep TER EC ga F Tire real Hana tel CN ge Bn ER E DD e ELE Ei cabled sl Enabled J Mag EqtertSebeck E e d B a RTE TT ap STT det Exit de Fu Pre THS Pelens F Faal SafFe Petan lis Fe OR shy letalis CPU Feature Menu Thermal Management Default Thermal Monitor 1 This option is used to manage CPU thermal lt Limit CPUID MaxVal Default Disabled The option is used to set limit CPUID MaxVal The available setting values are Disabled and Enabled Foxconn Chapter 3 BIOS Description Advanced Chipset Features CTIE hardi MS ORG Setep Btalits Gdegeced Chipsel Feateres t DREN Cleck Tinieg Lepirat Fress Eater stem EMIS Ciy ret Bodre RAM Cacherahle LE mai bed Hmary Bole ot P 16H hisa HTK BTE HEH Bele tle ere Dater Sejecri aa A Bi A alae Fi PES de DT aloes PbS Fail Safe Defaults Fis Dptumazed BefFaslis Advanced Chipset Features Menu e DRAM Clock Timing Control Press lt Enter gt to set the sub items of the DRAM clock timing For details please refer to page 32 System BIOS Cacheable Default Enabled Select Enabled to allow caching of the system BIOS which may improve performance If any other program writes to this memory area a system error may result The available setting values are Enabled and Disabled lt Video RAM Cacheable Default Enabled It is recommended that users set this op
16. ECISION INDUSTRY COMPANY LTD 66 CHUNG SHAN RD TU CHENG INDUSTRIAL DISTRICT TAIPEI HSIEN TAIWAN R O C declares that the product Motherboard 6497MB is in conformity with reference to the specification under which conformity is declared in accordance with 89 336 EEC EMC Directive Wl EN 55022 A1 2000 Limits and methods of measurements of radio disturbance characteristics of information technology equipment IV EN 61000 3 2 A14 2000 Electromagnetic compatibility EMC Part 3 Limits Section 2 Limits for harmonic current emissions equipment input current lt 16A per phase IV EN 61000 3 3 A1 2001 Electromagnetic compatibility EMC Part 3 Limits Section 2 Limits of voltage fluctuations and flicker in low voltage supply systems for equipment with rated current lt 16A V EN 55024 A1 2001 Information technology equipment Immunity characteristics limits and methods of measurement Signature Place Date TAIPEI 2004 Printed Name James Liang Position Title Assistant President 6497MB Engl i sh pref ace p65 3 2005 5 9 15 18 Declaration of conformity Trade Name Model Name Responsible Party Address Telephone Facsimile Equipment Classification Type of Product Manufacturer Address Supplementary Information Foxconn 6497MB PCE Industry Inc 458 E Lambert Rd Fullerton CA 92835 714 738 8868 714 738 8838 FCC Class B Subassembly Motherboard HON HAI PRECISION INDU
17. OWER 12V FAN1 sense CPU_FAN SENSE CONTROL Foxconn Chapter 2 Installation Instructions Audio Connectors CD_IN AUX_IN optional CD_IN AUX_IN is Sony standard CD audio connectors it can be connected to a CD ROM drive through a CD audio cable CD R AUX_R 1 L GND GND _ CD L AUX L CD_IN AUX_IN Speaker Connector SPEAKER The speaker connector is used to connect speaker of ee the chassis a SPKJ SPEAKER SPDIF Out Connector SPDIF OUT optional The S PDIF out connector is capable of providing digi ge tal audio to external speakers or compressed AC3 d SPDIF_OUT data to an external Dolby digital decoder We Note The empty pin of SPDIF cable should be aligned SPDIF_OUT to empty pin of SPDIF out connector S ATA Connectors SATA_1 SATA_2 optional The S ATA headers are used to connect the S ATA devices to the motherboard These connectors support the thin Serial ATA cables for primary internal storage devices The current Serial ATA interface allows up to 150MB s data transfer rate SATA _1 SATA 2 FOXCONN Chapter2 Installation Instructions Front Audio Connector F_AUDIO The audio interface provides two kinds of audio output choices the Front Audio the Rear Audio Their priority is sequenced from high to low AUD_RET R Front Audio to Rear Audio If headphones are Se plugged into the front panel of the chassis using the Front Audio then the Line out Rear E AUDIO Audio
18. STRY COMPANY LTD 66 CHUNG SHAN RD TU CHENG INDUSTRIAL DISTRICT TAIPEI HSIEN TAIWAN R O C This device complies with Part 15 of the FCC Rules Operation 1s subject to the follow ing two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Tested to comply with FCC standards RE Signature ae Lint lt J 6497MB Engl i sh pref ace p65 4 Date 2004 2005 5 9 15 18 Table of Contents Chapter Product Introduction Main Features cc cccccccccececececccccccececececeaccceececeneaeaceeeceneneaeacsneneceaneraes Ee Chapter 2 Installation Instructions Other Connectors 22 2 0 c ccc ccececececececececececececececececececececececececuceeeeeceseesceeess Expansion SOS eeectceissecenscaccecetauis nesceaniteomsuueacnes sauedeunesewetuseetuetersaumeedeeasedactanns JUMPE EE Chapter BIOS Description Enter BIOS Setup ccc cc ccc ccccccccecccececececececucncucucucucucucucacucucacaeaeaeaeaeaeeeanas Main Men Standard CMOS Features cccccccececececececececececececececenecenenecenenenenenenenees BIOS TE Advanced BIOS Features ccccccccccsececesceceeeeeeeceseeeesueeeseeeseeeeseneessaees Advanced Chipset Features cccccccsscccececeeceeeeseeesansecaeesaneeaueeseeesauss Integrated Peripherals cccccccccseccsececee
19. Statement This manual is the intellectual property of Foxconn Inc Although the information in this manual may be changed or modified at any time Foxconn does not obligate itself to inform the user of these changes Trademark All trademarks are the property of their respective owners Version User Manual V1 0 in English for 6497MB series motherboard P N 91 181 U49 M2 0E Symbol description RI Note refers to important information that can help you to use motherboard better Attention indicates that it may damage hardware or cause data loss and tells you how to avoid such problems Warning means that a potential risk of property damage or physical injury exists More information If you want more information about our products please visit Foxconn s website http www foxconnchannel com 6497MB Engl i sh pref ace p65 1 2005 5 9 15 18 Item Checklist Thanks for your purchasing Foxconn s 6497MB series motherboard Please check the package if there are missing or damaged items contact your distributor as soon as possible 6497MB motherboard x1 Foxconn Utility CD x1 6497MB User Manual x1 RAID User Manual x1 optional ICH6R RAID Floppy x1 optional IDE Ribbon Cable x1 FDD Ribbon Cable x1 I O Shield x1 S ATA Signal Cable x1 lt S ATA Power Cable x1 6497MB Engl i sh pref ace p65 2 2005 5 9 15 18 Declaration of conformity LE HON HAI PR
20. amage caused Foxconn Chapter 3 BIOS Description Advanced BIOS Features Pheemix hara BS GE Bees Btalite ad BUGS Feate i SI i Press i 2 bi n m I oa Ar lar no te Li amp CH dot CFE LE Cache LE mei Le qaper vn echt Technologas EE EFI L3 che ERE Ehecki iy dj LELI haar Be Zei lest eer ie farsa De Fiegen Brad d ERT ier dch Drier LR d na De Flappy Serk Enabled Bn te Bel s Etape Trpo ie Ia SEES hae ed Seceridy Rat ies Se ein tle cee SITT SEET i le ee Fil Same j ESEzExit WEIGHT ENT Betr PRS de DTW IST CG Fail Safe Deta sits Fiz OORT EIN Be Fa alis Advanced BIOS Features Menu CPU Feature Press lt Enter gt to set the items of CPU feature Please refer to page 30 Hard Disk Boot Priority This option is used to select the priority for HDD startup After pressing lt Enter gt you can select the HDD using the lt PageUp gt lt PageDn gt or Up Down arrow keys and change the HDD priority using lt gt or lt gt you can exit this menu by pressing lt Esc gt Virus Warning Default Disabled Allows you to choose the VIRUS warning feature for IDE hard disk boot sector protection If this function is enabled and someone attempt to write data into this area BIOS will show a warning message on screen and an alarm will beep The setting values are Disabled and Enabled Note Such function provides protection to the start up sector only it does not protect the e
21. eseeesceseeseeseeesceeeceeeseerseeeeseeescess Power Management Setup cccccccssccceeeeceseeceeseceeesseseceueeseaeeseeeesseeeens ie es e eu le Ee le EE Bee in Frequency Voltage Contol Load Fail Safe RT Beie Optimized el CTIE Set Supervisor User Password cccccccceecesececeeeceeecaeeeceesaueeseeeseueeaneeaes We oN n E EXIC VINOU SAVINO ME Chapter Driver CD Introduction Bit ae RE Start to Install Drivers 2 0 00 00 cccccccccccccccccccccccccccecuacsceacaceueacsueauseeaeaeeneaeanes 6497MB Engl i sh pref ace p65 5 2005 5 9 15 18 Warning 1 Attach the CPU and heatsink using silica gel to ensure full contact 2 It is suggested to select high quality certified fans in order to avoid damage to the motherboard and CPU due high temperatures 3 Never turn on the machine if the CPU fan is not properly installed 4 Ensure that the DC power supply is turned off before inserting or removing expansion cards or other peripherals especially when you insert or remove a memory module Failure to switch off the DC power supply may result in serious damage to your system or memory module Warning We cannot guarantee that your system will operate normally while over clocked Normal operation depends on the over clock capacity of your device OH Attention Since BIOS programs are upgraded from time to time the BIOS description in this manual is just for reference We do not guarantee that
22. ff Method Default DPMS Supported This option is used to define the video off method Blank Screen mode means that after the computer enters power saving mode only the monitor will close however the vertical and horizontal scanning movement of the screen continues When you select the V H SYNC Blank mode the vertical and hori zontal scanning movement of screen stops when the computer enters power saving mode DPMS Supported mode is a new screen power management system and it needs to be supported by the monitor you are using Switch Function Default Break Wake This option is used to enable or disable switch function to wake up The setting values are Disabled and Break Wake lt Hot Key Function As Default Power Off The option is used to define the hot key function The available setting values are Disabled Power off and Suspend lt HDD Off After Default Disabled This option is used to define the continuous HDD idle time before the HDD enters power saving mode The setting values are Disabled and 1 Min 15 Min lt Power Button Override Default Instant Off This option is used to set the power down method This function is only valid for systems using an ATX power supply When Instant Off is selected press the power switch to immediately turn off power When Delay 4 Sec is selected press and hold the power button for four seconds to turn off power lt Power State Resume Control Default
23. hus making your PC more personal ized and friendly FOXxconn Chapter 4 Driver CD Introduction c SuperUpdate SuperUpdate function can help to update the BIOS through Internet directly B Adobe Reader C Norton Internet Security 3 Browse CD Click here to browse CD content 4 HomePage Click here to visit Foxconn motherboard homepage ET Note 1 Install the latest patch first if your OS is Windows XP or Win dows 2000 2 Follow the CD screen order to install your motherboard drivers Start to Install Drivers Click lt Install Driver gt to enter the driver installation menu screen shown as below Click the relevant buttons to install IDE Driver SiS RAID optional DirectX 9 0b USB2 0 Driver Audio Driver and LAN Driver from this CD FOXCONN Utility CO SiS 649 Series DPE Peter IRE driwer dinstalletian d JES FADN 4 e i Follow the screen a ts _ order to install the USES T Gri ii motherboard drivers Aadio briw T aE ts F tJ OAH DeLagr E ERN
24. ides the ports as below For 6 channel 1394 Port optional LAN Port 4 Parallel Port Printer Port PS 2 Mouse Connector 2 PS 2 Keyboard Connector jal Serial Port S PDIF Coaxial uss 2 0 Ports COM1 For 8 channel PS 2 Mouse Connector This green 6 pin connector is for a PS 2 mouse PS 2 Keyboard Connector This purple 6 pin connector is for a PS 2 keyboard Serial Port COM1 This 9 pin COM1 port is for pointing devices or other serial devices O Parallel Port Printer Port This 25 pin port connects a parallel printer a scanner or other devices FOXCONN Chapter2 Installation Instructions S PDIF Coaxial Out Port This port connects to external audio output devices with coaxial cable connectors 1394 Port optional This digital interface supports electronic devices such as digital cameras scanners and printers USB 2 0 Ports These four Universal Serial Bus USB ports are available for connecting USB 2 0 1 1 devices O LAN Port L K optional This port allows connection to a Local Area Network LAN through a network hub Line in Line out Microphone Jacks for 6 channel When using a 2 channel sound source the Line Out jack is used to connect to speaker or headphone the Line In jack connects to an external CD player tape player or other audio device The Microphone jack is used to connect to the microphone When using a 6 channel sound source connect
25. keys select the item to set up and then use the lt PgUp gt or lt PgDn gt keys to choose the setting values ene ell paip TOET Itiliiy Ekandard Ee are Lag d e CNA TU lien Help Tise Ch see a er T IHE me l p Wester sc UI Bear iHome Hane pu E ima i Eki smd LL 4 E phaard O thee EnteriSeleci ai APP alme Fii Save ESCE FA Wel FSS Feeeoees THE PRS Faul Sate Deas lis FJ a ALEN od PeFamlis Standard CMOS Features Menu Date This option allows you to set the desired date usually as the current date with the lt day gt lt month gt lt date gt lt year gt format Day weekday from Sun to Sat defined by BIOS read only Month month from Jan to Dec Date date from 1 to 31 can be changed using the keyboard Year year set up by users Time This option allows you to set up the desired time usually as the current time with lt hour gt lt minute gt lt second gt format IDE Channel 0 1 Master Slave These categories identify the HDD types of 1 IDE channel installed in the com puter system There are three choices provided for the Enhanced IDE BIOS None Auto and Manual None means no HDD is installed or set Auto means the system can auto detect the hard disk when booting up by choosing Manual and changing Access Mode to CHS the related information should be entered manually Enter the information directly from the keyboard and press lt Enter
26. lease refer to page 35 lt Onboard SuperlO Device Press the lt Enter gt key to enter the setup sub menu For details please refer to page 36 lt IDE HDD Block Mode Default Enabled This option is used to set whether IDE HDD block mode is allowed Selecting Enabled will set IDE HDD as block mode When disabled IDE HDD does not support block mode lt MAC Access Interface Default EDB Bus optional This option is visible only when your motherboard features 10 100M LAN Foxconn Chapter3 BIOS Description Pheesd Pars CHR Setep tality SES Gelhio DIE E Datereal FEL TE Fuik DOE Primers Hisler FIND DIE Frimars lace FIR DOE Secondary Haster FDI DOE Secondary Sleee AL Pricery Master OltrabHa Ber sure Slane HIT Secondary Fasiri lt raDHA TECEN lave Ed DOE Forel Bede thee TTT fotert amp ebeck we FPilPi Gelder NG RT ESEtExit Fittemeral Be Lp PES Freeoses alors Fa Fail Safe Defaults Fis Dptumazed BefFaalis SIS Onchip IDE Menu Internal PCI IDE Default Both This option is used to set the ports of onboard IDE The available setting values are Disabled Primary Secondary and Both lt Primary Secondary Master Salve PIO Default Auto These four items let you assign which kind of PIO Programmed Input Output is used by IDE devices Choose Auto to let the system auto detect which PIO mode is best or select a PIO mode from 0 4 lt Primary Secondary Master Salve UDMA Default Auto UltraDMA tech
27. mal pins 2 and 3 together with the jumper cap 3 Turn the AC power supply back on OH Warning 1 Disconnect the power cable before adjusting the jumper settings 2 Do not clear the CMOS while the system is turned on FOXCONN Chapter2 Installation Instructions BIOS Protection Jumper FWH_EN1 The motherboard BIOS is inside the FWH If the jumper FWH_EN1 is set as CLOSED the system BIOS is pro tected from being attacked by a serious virus such as the CIH virus You will be unable to flash the BIOS to the motherboard when the system BIOS is protected CLOSED DISABLE c 123 OPEN nase CED 123 FWH_EN1 papte CH This chapter tells how to change system settings through the BIOS Setup menus Detailed descriptions of the BIOS pa rameters are also provided You have to run the Setup Program when the following cases occur 1 An error message appears on the screen during the system POST process 2 You want to change the default CMOS settings This chapter includes the following information I Q PV Q V te Ze Z Ze Ze Ze Ze ki Ze Ze 2 Ze Ze Enter BIOS Setup Main Menu Standard CMOS Features BIOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP PCI Configurations PC Health Status Frequency Voltage Control Load Fail Safe Defaults Load Optimized Defaults Set Supervisor User Pa
28. n press lt Enter gt The password you enter will replace any previous password When prompted key in the new password and press lt Enter gt Foxconn Chapter 3 BIOS Description If you do not want to set a password just press lt Enter gt when prompted to enter a password and in the screen the following message will appear If no password is keyed in any user can enter the system and view modify the CMOS settings PASSWORD DISABLED Press any key to continue Under the menu Advanced BIOS Features Setup if you select System from the Security Option you will be prompted to enter a password once the system is started or whenever you want to enter the CMOS setting program If the incor rect password is entered you will not be permitted to continue Under the menu Advanced BIOS Features Setup if you select Setup from the security Option you will be prompted to enter a password only when you enter the CMOS setting program Save amp Exit Setup When you select this option and press lt Enter gt the following message will appear in the center of the screen SAVE to CMOS and EXIT Y N Y Press lt Y gt to save your changes in CMOS and exit the program press lt N gt or lt ESC gt to return to the main menu Exit Without Saving If you select this option and press lt Enter gt the following message will appear in the center of the screen Quit Without Saving Y N N Press lt Y gt t
29. ned by the infrared module installed on the board lt UR2 Duplex Mode Default Half This option is available when UART 2 mode is set to either ASKIR or IrDA This item enables you to determine the infrared function of the onboard infrared chip lt Onboard Parallel Port Default 378 IRQ7 This item allows you to determine onboard parallel port controller I O address and interrupt request IRQ Setting values include Disabled 378 IRQ7 278 IRQ5 and 3BC IRQ7 lt Parallel Port Mode Default SPP Select an address and corresponding interrupt for the onboard parallel port Setting values include SPP EPP ECP ECP EPP lt ECP Mode Use DMA Default 3 select a DMA Channel for the parallel port when using the ECP mode This field is only configurable if Parallel Port Mode is set to ECP The available setting values are 3 and 1 Foxconn Chapter 3 BIOS Description Power Management Setup Pheemix 2 ech RS CNS Een TIET F TT Sel SEF matt ijan E mak bed SEF Seepeed Tree i j Zpeer Hannagrsegl Gas pend Hade Qadeo OFF Epi isa fides qt Pte q hed fwatch Eanrtiee HRTEM ge EF Jaq Hot CR ZP HIE UFF GFte freer Betten Beerride RI OI Fesane Comber ab EZE PE Wake Op Lee Belay Feoor is Thermal tL oils IT EP dna Bales HT E Ex ae aie Ne Ehz Pro TERES aimes Fk Fatl Safe Defaolts RER ed Be Fa Power Management Setup Menu lt ACPI Function Default Enabled ACPI stands for Advanced
30. nology provides faster access to IDE devices If you install a device that supports UltraDMA change the appropriate item on this list to Auto The available setting values are Disabled and Auto lt IDE Burst Mode Default Enabled This option is used to set whether the IDE burst mode is allowed The available setting values are Disabled and Enabled Foxconn Chapter 3 BIOS Description ee Ieee DM Setep Btalite SES fetkua FC P E E Ennirellber Emak bed ER 7 0 Supports EnabLed Ee es ard Super ae i Homer Soppar FTE IT Cru Enak bed EW WEI ETHE EBET Emak bed IS dires Dope Prese Eater SIS Serral FIA E tentrelier LE maki bed Jabear ai LOR Leetenl ler Enabled Baboard LEH Boot AIH Bish bed EE EEN W HUT fektert elect DFFG Baler STL Ze Exit Fitiemeral Bebe PES Frevuees Maloers F j la k zafe Defa sits Pptuimazed Befas lis SIS Onchip PCI Device Menu SIS USB Controller Default Enabled This option is used to enable or disable SIS USB controller USB Keyboard Mouse Support Default Enabled Select Enabled if you need to use a USB interfaced keyboard or mouse in the operating system The setting options include Enabled and Disabled SIS AC97 AUDIO Default Enabled This option is used to set whether onboard AC97 Audio is enabled The avail able setting values are Disabled and Auto SIS 10 100M ETHERNET Default Enabled optional This option is used to set whether 10
31. ntire hard disk CPU L1 amp L2 Cache Default Enabled This option is used to enable or disable the CPU L1 amp L2 cache Leave it at default unless the system runs abnormally when it is set as Enabled Set ting it as Disabled will adversely affect the system performance lt CPU L3 Cache Default Enabled optional This option is used to enable or disable CPU L3 cache The available set tings include Enabled and Disabled FOXCONN Chapter 3 BIOS Description lt Hyper Threading Technology Default Enabled This option is used to turn on or off the Hyper Threading function of the CPU The available setting values are Disabled and Enabled Note This function will not be displayed until a CPU that supports Hyper Threading has been installed First Second Third Boot Device Default Floppy Hard Disk CDROM This option allows you to set the boot device sequence The available setting values are Floppy LS120 Hard Disk CDROM ZIP 100 USB FDD USB ZIP USB CDROM LAN and Disabled lt Boot Other Device Default Enabled With this function set to Enabled the system will boot from some other devices if the first second third boot devices failed The available setting val ues are Disabled and Enabled Security Option Default Setup When it is set to Setup a password is required to enter the CMOS Setup screen When it is set to System a password is required not only to enter
32. o exit CMOS without saving your modifications press lt N gt or lt ESC gt to return to the main menu The utility CD that came with the motherboard contains use ful software and several utility drivers that enhance the motherboard features This chapter includes the following information Utility CD content o Start to Install drivers Foxconn Chapter 4 Driver CD Introduction Utility CD content This motherboard comes with one Utility CD To begin using the CD simply insert the CD into your CD ROM drive The CD will automatically display the main menu screen FOXCONN Utility CH SiS 649 Series p Install Gerdes tT moors see bes m Prone j maran 1 Install Driver Using this choice you can install all the drivers for your motherboard You should install the drivers in order and you need to restart your computer after the drivers are all installed A IDE Driver B SiS RAID optional C DirectX 9 0b D USB2 0 Driver E Audio Driver F LAN Driver 2 Accessories Use this option to install additional software programs A SuperUtility a SuperStep SuperStep is a powerful and easy to operate tool for overclocking You can quickly increase your CPU s working frequency through its user friendly interface It will enhance your CPU s performance and meet all kinds of DIY requirements b SuperLogo SuperLogo can display user designed graphics and pictures such as a company logo or personal photos t
33. or 21 USB Connectors 22 PCl Express x16 Slot 23 PCI Expansion Slots 24 SPDIF Out Connector optional 25 1394 Connector optional 26 Front Audio Connector Note This layout is provided for reference please refer to the physical motherboard Chapter This chapter introduces the hardware installation process in cluding the installation of the CPU memory power supply slots rear panel and pin headers and the mounting of jumpers Caution should be exercised during the installation of these modules Please refer to the motherboard layout prior to any installation and read the contents in this chapter carefully This chapter includes the following information CPU Memory Zei Ze Ze Power supply Ze Rear Panel Connectors Ze Other Connectors Ze Expansion Slots wi Ze Jumpers FOXCONN Chapter2 Installation Instructions CPU This motherboard supports single Pentium 4 Processor including Prescott desktop CPUs in an LGA775 package It also supports Hyper Threading Technology and FSB Dynamic Bus Inversion DBI Installation of CPU Below is the CPU socket illustration Follow these procedures to install a CPU Load plate Load cap 1 Lifted tab Foxconn Chapter 2 Installation Instructions 3 Use thumb amp forefinger to hold the hook of the load lever and pull the lever sideways to unlock it Correct Q Warnina DO NOT use finger
34. r To utilize this function set Case Open Warning to Enabled in the PC Health Status section of the CMOS Setup Save and exit to make sure this function takes effect 1 INTRUDERJ 2 GND INTR Foxconn Chapter 2 Installation Instructions Expansion Slots This motherboard includes three 32 bit Master PCI bus slots and one PCI Ex press x 16 slot PCI Slots The expansion cards can be installed in the three PCI slots When you install or take out such cards you must make sure that the power plug has been pulled out Please read carefully the instructions provided for such cards and install and set the necessary hardware and software for such cards such as the jumper or BIOS setup PCI Express Slot PCI Express will offer the following design advantages over the PCI and AGP interface Compatible with existing PCI drivers and software and Operating Systems High Bandwidth per Pin Low overhead Low latency PCI Express supports a raw bit rate of 2 5 Gb s on the data pins This results in a real bandwidth per pair of 250 MB s A point to point connection allows each device to have a dedicated connec tion without sharing bandwidth Ability to comprehend different data structure Low power consumption and power management features PCI Express will take two forms x16 and x1 PCI Express slots Whereas the x16 slot is reserved for graphic video cards the x1 slot is designed to accommo date less bandwidth in
35. roduct Introduction Main Features Size e mATX form factor of 9 6 inch x 8 5 inch Microprocessor D hy ding e Supports Intel Prescott T processor in an LGA775 package e Supports FSB at 533 800 MHz e Supports Hyper Threading technology Chipset e iS649 North Bridge SiS964 SiS964L South Bridge Memory FNDR400 Two 184 pin L t d e Supports up to 2 GB DDR memory Supports Single Channel DDR 400 333 266 e Registered memory not supported e Supports 128 Mb 256 Mb 512 Mb technologies USB 2 0 Ports e Supports hot plug e Eight USB 2 0 ports four rear panel ports two onboard USB headers providing four extra ports e Supports wake up from S1 and S3 mode e Supports USB 2 0 Protocol up to 480 Mbps transmission rate Onboard Serial ATA optional e 150 MBps transfer rate e Supports two S ATA devices e Supports RAID 0 RAID 1 JBOD Foxconn Chapter1 Product Introduction Onboard 1394 E optional FJ IEEE 1394 e Support hot plug e With rate of transmission at 400 Mbps e Self configured addressing e Can connect with 2 independent 1394 units synchronously at most Onboard LAN L K optional e Supports 10 100 1000 K optional Mbit sec Ethernet e LAN interface built in on board Onboard Audio 6 optional E e AC 97 2 3 Specification Compliant e Supports SPDIF output e Onboard Line in jack Microphone in jack Line out jack e Supports 6 channel audio setting via software CA
36. s The hotkey is Ctrl Alt Backspace The setting values are Any Key Hot Key and Password lt PS2MS Power Up Control Default Click This option used to set which action will wake up PS 2 mouse from 3 S4 S5 status The setting values are Disabled Click Move amp Click Power UP by Alarm Default Disabled This option is used to set the timing of the start up function In order to use this function the start up password function must be cancelled Also the PC power source must not be turned off Month Alarm This option is used to set the timing for the start up month The setting values contain 1 12 and NA FOXCONN Chapter 3 BIOS Description lt Day of Month Alarm This option is used to set the timing for the start up day of the month The setting values contain 0 31 Time hh mm ss Alarm This option is used to set the timing for the start up time The setting values contain hh 0 23 mm 0 59 ss 0 59 lt Primary Secondary IDE Default Disabled When these items are enabled the system will restart the power saving timeout counters when any activity is detected on any of the drives or devices on the primary or secondary IDE channels The setting values are Dis abled and Enabled Foxconn Chapter 3 BIOS Description PnP PCI Configurations P hnrnis bearda Dr SSE LIESE Cd Iert Bisplas First FET Star Then Help Becet Comfageretioan Data Bissbled Eecoerces Costrelbed Ey ete ESCH b
37. ssword Save amp Exit Setup Exit Without Saving Foxconn Chapter 3 BIOS Description Enter BIOS Setup The BIOS is the communication bridge between hardware and software correctly setting up the BIOS parameters is critical to maintain optimal system performance Power on the computer when the following message briefly appears at the bottom of the screen during the POST Power On Self Test press lt Del gt key to enter the AWARDBIOS CMOS Setup Utility Press TAB to show POST screen DEL to enter SETUP ET Note We do not suggest that you change the default parameters in the BIOS Setup and we shall not be responsible for any damage that result from any changes that you make Main Menu The main menu allows you to select from the list of setup functions and two exit choices Use the arrow keys to select among the items and press lt Enter gt to accept or go to the sub menu O TEE bears CHES Setep Stiliiy E Standard CHES Festeres i bregma lelieages Eootral b EDES Festores Laad Fail Safe DATE F RES EFestares lead bpl mized Defaults ee ee ee oe Te Set Pepereiser Passed gt iebegraied Peripierals Power Banegeern Eetop Case 2 Cazi Setup Pafs FEI Ce eat oes Peat Withee Saring PE Bealih States gt eat Tier Sanr amp ee ee a Tare Date Bard Disk Tepe Main Menu The items in the main menu are explained below Standard CMOS Features The basic system configuration
38. tal Memory Total memory of the system Foxconn Chapter3 BIOS Description BIOS Features Pheenix I eech ait DS DUT TEE Beterb e ST bed Super Ge ks lisab led FuperBeceeery Baltes LEF Raf crn leck OR IAH Fre Egrznt a Rat ta SFE tle re ater beck da Gales BTL cee CTS Fitieseral Bela PRE Prevuoes Waloes tie Gab Safe Detaults Bet Lndzed ie fan lil BIOS Features Menu lt SuperBoot SuperBoot Default Disabled SuperBoot allows system relevant information to be stored in CMOS upon the first normal startup of your PC and the relevant parameters will be restored to help the system start up more quickly on each subsequent startup The avail able setting values are Disabled and Enabled lt SuperBlOS Protect SuperBlIOS Protect Default Disabled SuperBlOS Protect function protects your PC from viruses e g CIH The avail able setting values are Disabled and Enabled lt SuperRecovery SuperRecovery Hotkey Default LSHIFT F1 SuperRecovery provides the users with an excellent data protection and HDD recovery function There are 12 optional hotkeys and the default hotkey is LSHIFT F1 SuperSpeed SuperSpeed CPU Clock Default depend on CPU This option is used to set the CPU clock CPU DRAM Frequency Ratio Default SPD This item is used to set the DRAM frequency ratio Warning Be sure your selection is right CPU overclock will be dangerous We will not be responsible for any d
39. tensive cards such as a modem or LAN card The difference in bandwidth between the x16 and x1 slots is notable to be sure with the x16 slot pushing 4GB sec 8GB sec concurrent of bandwidth and the x1 PCI Express slot offering 250MB sec Warning lf a performance graphics card was installed into 16x PCI Express slot 2 x 12 pin power supply was strongly recommended since that card maybe draws 75W power FOXCONN Chapter2 Installation Instructions Jumpers The users can change the jumper settings on this motherboard if needed This section explains how to use the various functions of this motherboard by chang ing the jumper settings Users should read the following content carefully prior to modifying any jumper settings Description of Jumpers 1 For the jumpers on this motherboard pin 1 can be identified by the silk screen printed A next to it However in this manual pin 1 is simply labeled as 1 2 The following table provides some explanation of the jumper pin settings User should refer to this when adjusting jumper settings Set pint and pin2 closed Clear CMOS Jumper CLR_CMOS The motherboard uses the CMOS RAM to store all NORMAL the set parameters The CMOS can be cleared by Default removing the CMOS jumper How to clear CMOS CLEAR 1 Turn off the AC power supply and connect pins 1 12 3 1 2 3 and 2 together using the jumper cap CLR CMOS 2 Return the jumper setting to nor
40. the front speaker to the green audio output connect the surround sound speaker to the blue audio output connect the center speaker subwoofer to the red Microphone output Line in Line out Microphone Rear LEF CEN Side Jacks for 8 channel When using an 8 channel sound source connect the front speaker to the green audio output connect the rear sound speaker to the black audio output con nect the center speaker subwoofer to the yellow audio output connect the side sound speaker to the blue audio output FOXCONN Chapter2 Installation Instructions Other Connectors This motherboard includes connectors for floppy IDE devices Serial ATA devices USB devices IR module and others FDD connector FLOPPY This motherboard includes a standard FDD connector supporting 360 K 720 K 1 2 M 1 44 M and 2 88 M FDDs HDD Connectors PIDE amp SIDE These connectors support the provided Ultra DMA 133 100 66 IDE hard disk ribbon cable Connect the cable s blue connector to the primary recommended or secondary IDE connector then connect the gray connector to the Ultra DMA 133 100 66 slave device hard disk drive and the black connector to the Ultra DMA 133 100 66 master device If you install two hard disks you must configure the second drive as a slave device by setting its jumper accordingly Refer to the hard disk documentation for the jumper settings i Attention Ribbon cables are directional therefore make sure
41. tion as the value Disabled so as to free the memory space and reduce the possibility of conflict occurrence lt Memory Hole At 15M 16M Default Disabled This option is used to determine whether the 15M 16M address field of memory is reserved for the ISA expansion card The available setting values are En abled and Disabled FOXCONN Chapter 3 BIOS Description wg Shaepis Rerdelis EES Tanta LIEU De Clair ai el DOE CEE Latency SPR DNEH Timing Cembra l r wn Pormuned Bape LESCHT Bata pass SES ied WET H Tosin imie E Bead Date UNE LIRE SEA ILRES HIR ties HUT Dater Selec Odd OuxRKTRITWNE RI RIICHT 3 Fithemeral HeLa PES de pens ET D TE Fail Safe Defaults Fis Dptumazed ie Fan lis DRAM Clock Timing Control Menu lt DDR CAS Latency Default SPD When synchronous DRAM is installed the number of clock cycles of CAS latency depends on the DRAM timing lt DRAM Timing Control Default Auto Selects whether DRAM timing is controlled by the SPD Serial Presence Detect EEPROM on the DRAM module Setting to Auto enables DRAM timings to be determined by BIOS based on the configurations on the SPD Selecting Manual allows users to configure the DRAM timings manually The setting values are Auto Manual Note The following options can be activated and configured only when this option is set as Manual lt RAS to CAS Delay tRCD Default Depend on memory It is used to
42. to lift the locking lever the improper operation will cause finger hurt and the SKT in a poor operation condition 4 Lift up the lever Use thumb to open the load plate Be careful not to touch the contacts 5 Hold the CPU and tilt it to some degree since the contacts are designed to be hooked then match the triangle marker to Pin 1 position as shown below Carefully insert the CPU into the socket until it fits in place Pin 1 indicator FOXCONN Chapter2 Installation Instructions 6 Close the load plate and slightly push down the tongue side Slightly push down the tongue side 7 Lower the lever and lock it to the load plate then the CPU is locked completely Note Excessive temperatures will severely damage the CPU and system Therefore you should install CPU cooling fan and make sure that the cooling fan works normally at all times in order to prevent overheating and damaging to the CPU Please refer to your _ CPU fan user guide to install it properly FOXCONN Chapter2 Installation Instructions Memory This motherboard includes two 184 pin slots with 2 5 V for DDR These slots support 256 Mb 512 Mb and 1 Gb DDR technologies for x8 and x16 devices You must install at least one memory bank to ensure normal operation Installation of DDR Memory 1 There is only one gap near the center of the DIMM slot and the memory module can be fixed in one direction only Unlock a DIMM slot b
43. y pressing the module clips outward 2 Align the memory module to the DIMM slot and insert the module vertically into the DIMM slot 104 Pins 80 Pins 3 The plastic clips at both sides of the DIMM slot will lock automatically D Warning Be sure to unplug the AC power supply before adding or removing expansion cards or other system peripherals especially the memory devices otherwise your motherboard or the system memory might be seriously damaged Foxconn Chapter 2 Installation Instructions Power Supply This motherboard uses an ATX power supply In order to avoid damaging any devices make sure that they have been installed properly prior to connecting the power supply 4 pin ATX_12 V Power Connector PWR2 The ATX power supply connects to PWR2 and 4 pin ATX_12 V power connector provides power to the CPU 24 pin ATX power connector PWR1 PWR1 is the ATX power supply connector Make 24 pin ATX power connector sure that the power supply cable and pins are RSVD PS ON properly aligned with the connector on the motherboard Firmly plug the power supply cable 24 into the connector and make sure it is secure i Pr ef T Er fA S o Note We strongly recommend that you use 24 pin power supply If you want to use 20 pin power supply you need to align the ATX power connec tor according to the right picture Foxconn Chapter 2 Installation Instructions Rear Panel Connectors This motherboard prov
Download Pdf Manuals
Related Search
Foxconn 6497MB series motherboard English user manual V1.0