Home

ASRock P4i48-M motherboard user manual

1. see p 8 No 25 AUD OUT R MIC POWER MIC This is an interface for front panel audio cable that allows convenient connection and control of audio devices System Panel Header 9 pin PANEL 1 see p 8 No 16 This header accommodates several system front panel functions Chassis Speaker Header SPEAKER Please connect the chassis 4 pin SPEAKER 1 DUMMY speaker to this header see p 8 No 17 ey Chassis Fan Connector Please connect a chassis fan 3 pin CHA_FAN1 tn cable to this connector and see p 8 No 15 CND TO match the black wire to the ground pin CPU Fan Connector GND Please connect a CPU fan cable 12V 3 pin CPU_FAN1 CPU FAN SPEED to this connector and match 000 see p 8 No 4 the black wire to the ground pin ATX Power Connector 20 pin ATXPWR1 see p 8 No 2 Please connect an ATX power supply to this connector Game Port Connector 15 pin GAME1 see p 8 No 21 5V 5V Connect a Game cable to this connector if the Game port bracket is installed 171 18 2 7 Serial ATA SATA Hard Disks Installation This motherboard adopts Intel ICH5 south bridge chipset that supports Serial ATA SATA hard disks You may install SATA hard disks on this motherboard for internal storage devices This section will guide you to install the SATA hard disks STE
2. the socket lever to secure the CPU The lever clicks on the side tab to indicate that it is locked Vever Up to 90 STEP 1 STEP 2 STEP 3 STEP 4 Lift The Socket Lever Up to 90 Match The CPU Marked Corner Push Down And Lock to The Socket Marked Corner The SocketLever 2 2 Installation of CPU Fan and Heatsink This motherboard adopts 478 pin CPU socket to support Intel Pentium 4 CPU It requires larger heatsink and cooling fan to dissipate heat You also need to spray thermal grease between the CPU and the heatsink to improve heat dissipation Make sure that the CPU and the heatsink are securely fastened and in good contact with each other Then connect the CPU fan to the CPU FAN connector CPU FAN1 see page 8 No 4 For proper installation please kindly refer to the instruction manuals of the CPU fan and the heatsink 111 12 2 3 Installation of Memory Modules DIMM P4i48 M motherboard provides two 184 pin DDR Double Data Rate DIMM slots Please make sure to disconnect power supply before adding or removing DIMMs or the system components Step 1 Unlock a DIMM slot by pressing the retaining clips outward Step 2 Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot lt notch M break The DIMM only fits in one correct orientation It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation Step 3
3. gt Floppy Configuration gt SuperIO Configuration u Go to Sub Screen gt USB Configuration General Help Load Defaults Save and Exit Exit Select Screen Select Item v02 54 C Copyright 1985 2003 American Megatrends Inc Setting wrong values in this section may cause L the system to malfunction 3 3 1 CPU Configuration BIOS SETUP UTILITY Advanced CPU Configuration Select how to set the CPU host frequency Actual Frequency MHz 200 Spread Spectrum Disabled Ratio Status Ratio Actual Value Select Screen CPU Thermal Throttling Disabled Select Item Change Option General Help Hyper Threading Technology Auto Load Defaults Max CPUID Value Limit Disabled Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc CPU Host Frequency While entering setup BIOS auto detects the present CPU host frequency of this motherboard The actual CPU host frequency will show in the following item Spread Spectrum This item should always be Auto for better system stability 21 I 122 Ratio Status This is a read only item which displays whether the ratio status of this motherboard is Locked or Unlocked If it shows Unlocked you will find an item Ratio CMOS Setting appears to allow you changing the ratio value of this motherboard If it shows Locked then the item Ratio CMOS Set ting will be hidden If you use the ratio value to time the CPU frequency
4. AC power remains off when the power recovers If Power On is selected the AC power resumes and the sys tem starts to boot up when the power recovers Ring In Power On Use this item to enable or disable Ring In signals to turn on the system from the power soft off mode PCI Devices Power On Use this item to enable or disable PCI devices to turn on the system from the power soft off mode PS 2 Keyboard Power On Use this item to enable or disable PS 2 keyboard to turn on the system from the power soft off mode RTC Alarm Power On Use this item to enable or disable RTC Real Time Clock to power on the system 3 3 4 IDE Configuration BIOS SETUP UTILITY Advanced T Set Compatible Mode Do re when both Legacy OS MS DOS Win Me 98SE and SATA device OnBoard IDE Controller Both are used gt Primary IDE Master Hard Disk Set Enhanced Mode gt Primary IDE Slave Not Detected when Native OS Secondary IDE Master Not Detected Win 2000 XP gt Secondary IDE Slave Not Detected is used FSATA1 Not Detected PSATA2 Not Detected saltet Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc OnBoard IDE Operate Mode Please select Compatible Mode when you install legacy OS Windows ME 98SE into SATA device If you install legacy OS into IDE HDD while SATA devices are used you also need to select Compatible Mode If nat
5. Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated 2 4 Expansion Slots PCI and AGP Slots There are 3 PCI slots and 1 AGP slot on P4i48 M motherboard PCI slots PCI slots are used to install expansion cards that have the 32 bit PCI interface AGP slot The AGP slot is used to install a graphics card The ASRock AGP slot A has a special locking mechanism which can securely fasten the graph ics card inserted Please do NOT use a 3 3V AGP card on the AGP slot of this motherboard It may cause permanent damage For the voltage information of your graphics card please check with the graphics card vendors Installing an expansion card Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Before installing the expansion card please make sure that the power supply is switched off or the power cord is unplugged Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation Remove the system unit cover if your motherboard is already installed in a chassis Remove the bracket facing the slot that you intend to use Keep the screws for later use Align the card connector with the slot and press firmly until the card is completely seated on the slot Fasten the card to the chassis with screws Replace the system cover 131 I 14 2 5 Jumpers Setup The illustrati
6. Select Item Enter Go to Sub Screen F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 3 5 1 Boot Settings Configuration BIOS SETUP UTILITY Boot Settings Configuration To enable or disable the boot from network feature Bootup Num Lock Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Boot From Network Use this item to enable or disable the Boot From Network feature Boot Up Num Lock If this item is set to On it will automatically activate the Numeric Lock function after boot up 31 Il I 32 3 5 2 Boot Device Priority In this section you may specify the boot sequence from the available devices in your system BIOS SETUP UTILITY Boot Device Priority Specifies the boot sequence from the available devices 2nd Boot Device HDD PM MAXTOR 6L08 3rd Boot Device CD DVD A device enclosed in parenthesis has been disabled in the corresponding type menu Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Likewise you may also specify the boot sequence from the available devices for the hard disk drives the removable drives and the CD DVD drives 3 6 Security Screen In this section you may set or change the supe
7. USB 2 0 Support Use this item to enable or disable the USB 2 0 support Legacy USB Support Use this item to enable or disable the support to emulate legacy I O devices such as mouse keyboard etc Or you may select Auto so that the system will start to auto detect if there is no USB device connected Auto option will disable the legacy USB support 3 4 Hardware Health Event Monitoring Screen In this section it allows you to monitor the status of the hardware on your system including the parameters of the CPU temperature motherboard temperature CPU fan speed chassis fan speed and the critical voltage BIOS SETUP UTILITY Main Advanced H W Monitor Hardware Health Event Monitoring CPU Temperature M B Temperature CPU Fan Speed Chassis Fan Speed Vcore 3 30V 5 00V 12 00V 2 37 C 98 F 31 C 8TF 2463 RPM N A 1 629V 3 306V 5 067V 11 890V Security Select Screen Select Item General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc I 30 3 5 Boot Screen In this section it will display the available devices on your system for you to config ure the boot settings and the boot priority BIOS SETUP UTILITY Main Advanced H W Monitor Security Exit Boot Settings Configure Settings during System Boot y Boot Device Priority y Hard Disk Drives y Removable Drives gt CD DVD Drives gt Select Screen til
8. it will be equal to the core speed of the installed processor Ratio Actual Value This is a read only item which displays the ratio actual value of this motherboard CPU Thermal Throttling You may select Enabled to enable P4 CPU internal thermal control mecha nism to keep the CPU from overheated Hyper Threading Technology To enable this feature it requires a computer system with an Intel Pentium 4 processor that supports Hyper Threading technology and an operating sys tem that includes optimization for this technology such as Microsoft Win dows XP Set to Auto if using Microsoft Windows XP or Linux kernel version 2 4 18 or higher This option will be hidden if the installed CPU does not support Hyper Threading technology Max CPUID Value Limit For Prescott CPU only some OSes ex NT4 0 cannot handle the function with disable This should be enabled in order to boot legacy OSes that cannot support CPUs with extended CPUID functions 3 3 2 Chipset Configuration BIOS SETUP UTILITY Advanced Chipset Configuration 133MHz DDR266 Flexibility Option Disabled 166MHz DDR333 Configure DRAM Timing by SPD Disabled 200MHz DDR400 DRAM CAS Latency Auto Auto DRAM RAS Precharge 4 Clocks DRAM RAS to CAS Delay 4 Clocks DRAM Precharge Delay 8 Clocks DRAM Burst Length 8 Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit Memory Hole Disabl
9. API Removable Media Device such as MO LBA Large Mode Use this item to select the LBA Large mode for a hard disk gt 512 MB under DOS and Windows for Netware and UNIX user select Disabled to disable the LBA Large mode I 26 Block Multi Sector Transfer The default value of this item is Auto If this feature is enabled it will enhance hard disk performance by reading or writing more data during each transfer PIO Mode Use this item to set the PIO mode to enhance hard disk performance by optimizing the hard disk timing DMA Mode DMA capability allows the improved transfer speed and data integrity for compatible IDE devices S M A R T Use this item to enable or disable the S M A R T Self Monitoring Analysis and Reporting Technology feature Configuration options Disabled Auto Enabled 32 Bit Data Transfer Use this item to enable 32 bit access to maximize the IDE hard disk data transfer rate 3 3 5 PCIPnP Configuration BIOS SETUP UTILITY Advanced PCI PnP Configuration Value in units of PCI L clocks for PCI device latency timer register PCI IDE BusMaster Enabled Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc PCI Latency Timer The default value is 32 It is recommended to keep the default value unless the installed PCI expansion cards specifications require other settings PCI IDE BusMaste
10. ASRocK P4i48 M User Manual Version 1 0 Published November 2004 Copyright 2004 ASRock INC All rights reserved Copyright Notice No part of this manual may be reproduced transcribed transmitted or translated in any language in any form or by any means except duplication of documentation by the purchaser for backup purpose without written consent of ASRock Inc Products and corporate names appearing in this manual may or may not be regis tered trademarks or copyrights of their respective companies and are used only for identification or explanation and to the owners benefit without intent to infringe Disclaimer Specifications and information contained in this manual are furnished for informa tional use only and subject to change without notice and should not be constructed as a commitment by ASRock ASRock assumes no responsibility for any errors or omissions that may appear in this manual With respect to the contents of this manual ASRock does not provide warranty of any kind either expressed or implied including but not limited to the implied warran ties or conditions of merchantability or fitness for a particular purpose In no event shall ASRock its directors officers employees or agents be liable for any indirect special incidental or consequential damages including damages for loss of profits loss of business loss of data interruption of business and the like even if ASRock has been advised of the pos
11. OS SETUP UTILITY after POST restart the system by pressing lt Ctl gt lt Alt gt lt Delete gt or by pressing the reset button on the system chassis You may also restart by turning the system off and then back on Because the BIOS software is constantly being updated the following BIOS setup screens and descriptions are for refer ence purpose only and they may not exactly match what you See on your screen 3 1 1 BIOS Menu Bar The top of the screen has a menu bar with the following selections Main To set up the system time date information Advanced To set up the advanced BIOS features H W Monitor To display current hardware status Boot To set up the default system device to locate and load the Operating System Security To set up the security features Exit To exit the current screen or the BIOS SETUP UTILITY Use lt lt gt key or lt gt gt key to choose among the selections on the menu bar and then press lt Enter gt to get into the sub screen 191 3 1 2 Navigation Keys Please check the following table for the function description of each navigation key Navigation Key s Function Description ex Moves cursor left or right to select Screens EUR Moves cursor up or down to select items To change option for the selected items lt Enter gt To bring up the selected screen F1 To display the General Help Screen F9 To load optimal default values for all the settings lt F10 gt To save chang
12. P Configuration 27 3 3 6 Floppy Configuration 0 cee eeeeeseeeeeeeeeeeees 28 3 3 7 Super IO Configuration 28 3 3 8 USB Configuration sees 30 3 4 Hardware Health Event Monitoring Screen 30 8 5 Boot Screen 31 3 5 1 Boot Setting Configuration s es 31 8 5 2 Boot Device Priority 32 3 6 Security Screen 32 3 7 Exit Screen Il 4 4 Software Support 34 4 1 Install Operating System seses 34 4 2 Support CD Information eee 34 4 2 14 Running Support CD sese 34 4 2 2 Drivers Menu rentre 34 4 2 3 Utilities Menu eee 34 4 2 4 Contact Information eee 34 Chapter 1 Introduction Thank you for purchasing ASRock P4i48 M motherboard a reliable motherboard produced under ASRock s consistently stringent quality control It delivers excellent performance with robust design conforming to ASRock s commitment to quality and endurance In this manual chapter 1 and 2 contain introduction of the motherboard and step by step guide to the hardware installation Chapter 3 and 4 contain the configuration guide to BIOS setup and information of the Support CD N Because the motherboard specifications and the BIOS software might be updated the content of this manual will be subject to change without notice In case any modifications of this manual occur th
13. P t STEP2 STEP3 STEP 4 STEP5 STEP6 STEP 7 Install the SATA hard disks into the drive bays of your chassis Connect the SATA power cable to the SATA hard disk Connect one end of the SATA data cable to the motherboard s primary SATA connector SATA1 Connect the other end of the SATA data cable to the primary SATA hard disk If you just want to install only one SATA HDD the installation process is complete at this step If you want to install two SATA HDDs please continue to do the following steps Connect the SATA power cable to the SATA hard disk Connect one end of the second SATA data cable to the motherboard s secondary SATA connector SATA2 Connect the other end of the SATA data cable to the secondary SATA hard disk Before you install OS into the SATA hard disk you need to check and ensure the configuration of the OnBoard IDE Operate Mode option in BIOS setup is correct according to the condition of your system For the configuration details please refer to the instruction on page 25 3 BIOS SETUP UTILITY 3 1 Introduction This section explains how to use the BIOS SETUP UTILITY to configure your system The BIOS FWH chip on the motherboard stores the BIOS SETUP UTILITY You may run the BIOS SETUP UTILITY when you start up the computer Please press F2 during the Power On Self Test POST to enter the BIOS SETUP UTILITY otherwise POST will continue with its test routines If you wish to enter the BI
14. SATA EF 14 1 PCI 3 Battery 5 Tie nee 15 PS2 USB PWR1 Jumper ATX Power Connector ATXPWR1 CPU Socket CPU Fan Connector CPU FAN1 CPU Heatsink Retention Module 184 pin DDR DIMM Slots DDR1 2 Secondary IDE Connector IDE2 Black Primary IDE Connector IDE1 Blue North Bridge Controller AGP Slot 1 5V AGP1 South Bridge Controller USB 2 0 Header USB67 Blue Secondary Serial ATA Connector SATA2 Primary Serial ATA Connector SATA1 15 16 17 18 BNBRRBRNBS Chassis Fan Connector CHA_FAN1 System Panel Header PANEL1 Chassis Speaker Header SPEAKER 1 Clear CMOS Jumper CLRCMOSO Infrared Module Header IR1 Floppy Connector FLOPPY1 Game Port Connector GAME1 Internal Audio Connector AUX1 White Internal Audio Connector CD1 Black JR1 JL1 Jumpers Front Panel Audio Header AUDIO1 PCI Slots PCI1 3 BIOS FWH Chip Shared USB 2 0 Header USBA 5 Blue 1 4 ASRock I O Plus oa kwon Lg Parallel Port 7 RJ 45 Port 8 Line In Light Blue 9 Line Out Lime 10 Microphone Pink 11 Shared USB 2 0 Ports USB45 USB 2 0 Ports USBO1 USB 2 0 Ports USB23 Serial Port COM1 PS 2 Keyboard Port Purple PS 2 Mouse Port Green I 10 Chapter 2 Installation P4i48 M is a Micro ATX form factor 9 6 in x 7 8 in 24 4 cm x 19 8 cm motherboard Before you install the motherboard study the config
15. TA HDD connect to the power connector power supply Please connect the black end of SATA power cable to the power connector on each drive Then connect the white end of SATA power cable to the power connector of the power supply USB 2 0 Header 9 pin USB67 SnD DUMMY see p 8 No 12 5 5 BR USB_PWR ASRock I O Plus accommo dates 6 default USB 2 0 ports If those USB 2 0 ports on the I O panel are not sufficient this USB 2 0 header is available to support 2 additional USB 2 0 ports Shared USB 2 0 Header 9 pin USB4 5 P 5 P 5 see p 8 No 28 l enD DUMMY This USB45 connector is shared with the USB 2 0 ports 4 5 on ASRock I O Plus When using the front panel USB ports by attaching the front panel USB cable to this connector USB4_5 the USB ports 4 5 on ASRock I O Plus will not be able to function Infrared Module Header ROX y DUMMY 5 pin IR1 STE see p 8 No 19 1 This header supports an optional wireless transmitting and receiving infrared module Internal Audio Connectors 4 pin CD1 4 pin AUX1 AURTE ep GND GND GND GND CD1 see p 8 No 23 AUX R CD R AUX1 see p 8 No 22 These connectors allow you to receive stereo audio input from sound sources such as a CD ROM DVD ROM TV tuner card or MPEG card Front Panel Audio Header 9 pin AUDIO1 BACKOUT R BACKOUT L Oo AUD OUT L GND
16. and 2E8 IRQ3 Parallel Port Address Use this item to set the address for the onboard parallel port or disable it Configuration options Disabled 378 and 278 Parallel Port Mode Use this item to set the operation mode of the parallel port The default value is ECP EPP If this option is set to DECP EPP it will show the EPP version in the following item EPP Version Configuration options Normal Bi Directional and ECP EPP EPP Version Use this item to set the EPP version Configuration options 1 9 and 1 7 ECP Mode DMA Channel Use this item to set the ECP mode DMA channel Configuration options DMAO DMA1 and DMAQ3 Parallel Port IRQ Use this item to set the IRQ for the parallel port Configuration options IRQ5 and IRQ7 OnBoard Game Port Use this item to enable the Game Port or disable it OnBoard MIDI Port Use this itme to select the address for the MIDI Port or disable it Configura tion options Disabled 300 and 330 29 I 3 3 8 USB Configuration BIOS SETUP UTILITY Advanced USB Configuration USB Devices Enabled None USB 2 0 Support Enabled Legacy USB Support Disabled To enable or disable the onboard USB controllers Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc USB Controller Use this item to enable or disable the use of USB controller
17. aults When you select this option it will pop out the following message Load optimal defaults Select OK to load the default values for all the setup configurations 33 I Chapter 4 Software Support 4 1 Install Operating System This motherboard supports various Microsoft Windows operating systems 98 SE ME 2000 XP Because motherboard settings and hardware options vary use the setup procedures in this chapter for general reference only Refer to your OS documentation for more information 4 2 Support CD Information The Support CD that came with the motherboard contains necessary drivers and useful utilities that enhance the motherboard features 4 2 1 Running The Support CD To begin using the support CD insert the CD into your CD ROM drive The CD automatically displays the Main Menu if AUTORUN is enabled in your computer If the Main Menu did not appear automatically locate and double click on the file ASSETUP EXE from the BIN folder in the Support CD to display the menus 4 2 2 Drivers Menu The Drivers Menu shows the available devices drivers if the system detects installed devices Please install the necessary drivers to activate the devices 4 2 3 Utilities Menu The Utilities Menu shows the applications software that the motherboard supports Click on a specific item then follow the installation wizard to install it 4 2 4 Contact Information If you need to contact ASRock or want to know mor
18. e about ASRock welcome to visit ASRock s website at http www asrock com or you may contact your dealer for further information I 34
19. e updated version will be available on ASRock website without further notice You may find the latest memory and CPU support lists on ASRock website as well ASRock website http www asrock com 1 1 Package Contents ASRock P4i48 M Motherboard Micro ATX Form Factor 9 6 in x 7 8 in 24 4 cm x 19 8 cm ASRock P4i48 M Quick Installation Guide ASRock P4i48 M Support CD One 80 conductor Ultra ATA 66 100 IDE Ribbon Cable One Ribbon Cable for a 3 5 in Floppy Drive One Serial ATA SATA Data Cable One Serial ATA SATA HDD Power Cable Optional One ASRock I O Plus Shield 1 2 Specifications Platform CPU Chipsets Memory IDE Serial ATA Floppy Port Audio PCI LAN Hardware Monitor PCI slots AGP slot USB 2 0 ASRock I O Plus BIOS Micro ATX Form Factor 9 6 in x 7 8 in 24 4 cm x 19 8 cm Socket 478 supports Intel Pentium 4 Prescott Northwood Willimate Celeron processor North Bridge Intel 848P chipset FSB 800 533 400MHz supports Hyper Threading Technology see CAUTION 1 South Bridge Intel ICH5 supports SATA 1 5Gb s 2DDR DIMM slots DDR1 and DDR2 supports PC3200 DDR400 PC2700 DDR333 PC2100 DDR266 Max 2GB see CAUTION 2 IDE1 ATA 100 Ultra DMA Mode 5 IDE2 ATA 100 Ultra DMA Mode 5 Supports up to 4 IDE devices Supports up to 2 SATA devices at 1 5Gb s data transfer rate Not Support RAID and Hot Plug functions Supports up to 2 floppy disk drive
20. ed Init Graphic Adapter Priority PCI AGP Graphics Aperture Size 64MB OnBoard LAN Enabled OnBoard AC 97 Audio Auto v02 54 C Copyright 1985 2003 American Megatrends Inc DRAM Frequency If Auto is selected the motherboard will detect the memory module s inserted and assigns appropriate frequency automatically You may also select other value as operating frequency 133MHz DDR 266 166MHz DDR 333 200MHz DDR 400 Flexibility Option The default value of this option is Disabled It will allow better tolerance for memory compatibility when it is set to Enabled Configure DRAM Timing by SPD Select Enabled will configure the following items by the contents in the SPD Serial Presence Detect device DRAM CAS Latency Use this item to adjust the means of memory accessing Configuration options Auto 2 5 2 and 3 Please note that the configuration option 3 is available only for FSB 800 and FSB 533 DRAM RAS Precharge This controls the idle clocks after a precharge command is issued Configuration options 4 Clocks 3 Clocks and 2 Clocks DRAM RAS to CAS Delay This controls the latency between the DRAM active command and the read write command Configuration options 4 Clocks 3 Clocks and 2 Clocks DRAM Precharge Delay This controls the number of DRAM clocks for RAS minimum Configura tion options 8 Clocks 7 Clocks 6 Clocks and 5 Clocks DRAM Burst Length DRAM Burst l
21. ength can be set as 8 or 4 Memory Hole The default value of this item is Disabled or you may set the value of this item as 15MB 16MB Init Graphic Adapter Priority This allows you to select PCI AGP and AGP PCI as the initial graphics adapter priority The default vaule is PCI AGP Graphics Aperture Size It refers to a section of the PCI memory address range used for graphics memory It is recommended to leave this field at the default value unless the installed AGP card s specifications requires other sizes OnBoard LAN This allows you to enable or disable the OnBoard LAN feature OnBoard AC 97 Audio Select Auto Enabled or Disabled for the onboard AC 97 Audio feature 23 I I 24 3 3 3 ACPI Configuration BIOS SETUP UTILITY Advanced ACPI Settings Select auto detect or EEG EGG disable the STR feature Restore on AC Power Loss Power Off Ring In Power On Disabled PCI Devices Power On Disabled PS 2 Keyboard Power On Disabled RTC Alarm Power On Disabled Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Suspend to RAM Use this item to select whether to auto detect or disable the Suspend to RAM feature Select Auto will enable this feature if the OS supports it Restore on AC Power Loss Use this item to set the power state after an unexpected AC power loss If Power Off is selected the
22. er as the example in the following instruction which can be applied to the configurations of Primary IDE Slave Sec ondary IDE Master Secondary IDE Slave SATA1 and SATA2 as well BIOS SETUP UTILITY Advanced Primary IDE Master Select the type gt of device connected Device Hard Disk to the system Vendor ST340014A Size 40 0 GB LBA Mode Supported Block Mode 16Sectors PIO Mode 4 Async DMA MultiWord DMA 2 Ultra DMA Ultra DMA 5 S M A R T Supported Select Screen LBA Large Mode enl Select tom Block Multi Sector Transfer uto 2 PIO Mode Auto Change Option DMA Mode Auto General Help S M A R T Disabled Load Defaults 32Bit Data Transfer Disabled Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc TYPE Use this item to configure the type of the IDE device that you specify Configuration options Not Installed Auto CD DVD and ARMDJ Not Installed Select Not Installed to disable the use of IDE device Auto Select Auto to automatically detect the hard disk drive 7 After selecting the hard disk information into BIOS use a disk 3 utility such as FDISK to partition and format the new IDE hard disk drives This is necessary so that you can write or read data from the hard disk Make sure to set the partition of the Primary IDE hard disk drives to active CD DVD This is used for IDE CD DVD drives ARMD This is used for IDE ARMD AT
23. es and exit the BIOS SETUP UTILITY lt ESC gt To jump to the Exit Screen or exit the current screen 3 2 Main Screen When you enter the BIOS SETUP UTILITY the Main screen will appear and display the system overview BIOS SETUP UTILITY Advanced H W Monitor Boot Security System Overview Use Enter TAB or SHIFT TAB to L 00 09 select a field System Date Fri 11 05 2004 Use or to configure system Time P4i48 M BIOS P1 00 Intel R Pentium R 4 CPU 3 2GHz 3200 MHz 2 1024KB Select Screen 0F34 0E Select Item Change Field Total Memory 256MB Select Field DIMM 1 256MB 166MHz DDR333 General Help DIMM 2 None Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc System Time Hour Minute Second Use this item to specify the system time System Date Day Month Date Year Use this item to specify the system date I 20 3 3 Advanced Screen In this section you may set the configurations for the following items CPU Configuration Chipset Configuration ACPI Configuration IDE Configuration PCIPnP Configuration Floppy Configuration SuperlO Configuration and USB Configuration BIOS SETUP UTILITY Advanced H W Monitor Security Advanced Settings Configure CPU WARNING Setting wrong values in below sections may cause system to malfunction y Chipset Configuration gt ACPI Configuration gt IDE Configuration gt PCIPnP Configuration
24. ically shutdown Before you resume the system please check if the CPU fan on the motherboard functions properly and unplug the power cord then plug it back again To improve heat dissipation remember to spray thermal grease between the CPU and the heatsink when you install the PC system 4 Do NOT use a 3 3V AGP card on the AGP slot of this motherboard It may cause permanent damage 5 Power Management for USB 2 0 works fine under Microsoft Windows XP SP1 2000 SP4 It may not work properly under Microsoft Windows 98 ME 6 Although this motherboard offers stepless control it is not recommended to perform over clocking Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU Il 8 1 3 Motherboard Layout MN OO O1 BR ND a B amp ND T 2 3 4 5 6 19 8cm 7 8 in e gt 177 o ol 2a 2 e 3 g i amp s s 9 J EE EN 7 Ee te O OE ale BIS sui mie Intel 6 E35 re gt oe ajjaj z x 848 su EHENES Chipset aS PLS gt i zx sai SV ILI r 8 AGPSX 1 5V AGP1 IDE 9 10 Intel CAN USB2 0 ICH5 2 26 Per ng 13 5 1CH GEERT ES
25. ive OS Windows 2000 XP is installed into SATA device please select Enhanced Mode You also need to select Enhanced Mode while native OS is installed into IDE HDD and SATA devices are used If you do not install any SATA device please also select Enhanced Mode no matter you use legacy OS or native OS for the system Please note that the following options will be varied depending on the OnBoard IDE Operate Mode Compatible Mode or Enhanced Model that you selected When Enhanced Mode is selected OnBoard IDE Controller You may enable either the primary IDE channel or the secondary IDE channel Or you may enable both the primary and the secondary IDE channels by selecting Both Set to Disabled will disable the both Configuration options Disabled Primary Secondary Both When Compatible Mode is selected Combined Mode Option It allows you to select between Pri IDE SATA and SATA Sec IDE If itis set to Pri IDE SATA then the secondary IDE will not work Likewise if it is set to SATA Sec IDE then the primary IDE will not work A V Because Intel ICH5 south bridge only supports four IDE devices under legacy OS Windows ME 98SE you have to choose either Pri IDE SATA or SATA Sec IDE when the installed SATA device is used with legacy OS 25 I IDE Device Configuration You may set the IDE configuration for the device that you specify We will use the Primary IDE Mast
26. on shows how jumpers are setup When the jumper cap is placed on pins the jumper is Short If no jumper cap u is placed on pins the jumper is Open The illustration shows a 3 pin jumper whose pin1 ag Gia da and pin2 are Short when jumper cap is Short O placed on these 2 pins m ERR Jumper Setting Description PS2 USB PWR1 12 23 Short pin2 pin3 to enable see p 8 No 1 Dm fS 5VSB standby for PS 2 5V 5VSB or USB wake up events Note To select 5VSB it requires 2 Amp and higher standby current provided by power supply JR1 see p 8 No 24 mE JL 1 see p 8 No 24 JR1 JL1 Note If the jumpers JL1 and JR1 are short both the front panel and the rear panel audio connectors can work Clear CMOS CLRCMOSO 2 pin jumper aoe see p 8 No 18 2 pin jumper Note CLRCMOSO allows you to clear the data in CMOS The data in CMOS includes system setup information such as system password date time and system setup parameters To clear and reset the system parameters to default setup please turn off the computer and unplug the power cord then use a jumper cap to short the pins on CLRCMOSO for 3 seconds Please remember to remove the jumper cap after clearing the CMOS If you need to clear the CMOS when you just finish updating the BIOS you must boot up the system first and then shut it down before you do the clear CMOS action 2 6 Onboard Headers and Connectors Onboard headers and connectors are NOT j
27. r Use this item to enable or disable the PCI IDE BusMaster feature 27 I I 28 3 3 6 Floppy Configuration In this section you may configure the type of your floppy drive BIOS SETUP UTILITY Advanced Floppy Configuration Select the type of CC floppy drive connected to the Floppy B Disabled system Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 3 3 7 Super IO Configuration BIOS SETUP UTILITY Advanced Configure Super IO Chipset Allow BIOS to Enable RE or Disable Floppy Controller Serial Port Address 3F8 IRQ4 Infrared Port Address Disabled Parallel Port Address 378 Parallel Port Mode ECP EPP EPP Version 1 9 ECP Mode DMA Channel DMA3 Parallel Port IRQ IRQ7 OnBoard Game Port Enabled OnBoard MIDI Port Disabled Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc OnBoard Floppy Controller Use this item to enable or disable floppy drive controller Serial Port Address Use this item to set the address for the onboard serial port or disable it Configuration options Disabled 3F8 IRQ4 2F8 IRQ3 3E8 IRQ4 2E8 IRQ3 Infrared Port Address Use this item to set the address for the onboard infrared port or disable it Configuration options Disabled 2F8 IRQ3
28. rvisor user password for the system For the user password you may also clear it BIOS SETUP UTILITY Main Advanced H W Monitor Boot Security Security Settings Install or Change the password Supervisor Password Not Installed User Password Not Installed Change User Password Clear User Password Select Screen ity Select Item Enter Change F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit v02 54 C Copyright 1985 2003 American Megatrends Inc 3 7 Exit Screen BIOS SETUP UTILITY Advanced H W Monitro HII Security Exit Options Exit system setup after saving the changes Discard Changes and Exit Discard Changes F10 key can be used for this operation Load Optimal Defaults Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit v02 54 C Copyright 1985 2003 American Megatrends Inc Save Changes and Exit When you select this option it will pop out the following message Save configuration changes and exit setup Select OK to save the changes and exit the BIOS SETUP UTILITY Discard Changes and Exit When you select this option it will pop out the following message Dis card changes and exit setup Select OK to exit the BIOS SETUP UTILITY without saving any changes Discard Changes When you select this option it will pop out the following message Dis card changes Select OK to discard all changes Load Optimal Def
29. s 5 1 channels AC 97 Audio Speed 802 3u 10 100 Ethernet supports Wake On LAN CPU temperature sensing Chassis temperature sensing CPU overheat shutdown to protect CPU life ASRock U COP see CAUTION 3 CPU fan tachometer Chassis fan tachometer Voltage monitoring 12V 5V 3 3V Vcore 3 PCI slots with PCI Specification 2 2 1 AGP slot supports 1 5V 8X 4X AGP card see CAUTION 4 8 USB 2 0 ports includes 6 default USB 2 0 ports on the rear panel plus two headers to support 2 additional USB 2 0 ports see CAUTION 5 1 PS 2 mouse port 1 PS 2 keyboard port 1 serial port COM1 1 parallel port ECP EPP support 6 default USB 2 0 ports 1 RJ 45 port Audio Jack Line In Line Out Microphone AMI legal BIOS OS Supports Plug and Play ACPI 1 1 compliance wake up events Supports jumperfree CPU frequency stepless control only for advanced users reference see CAUTION 6 Microsoft Windows 98 SE ME 2000 XP compliant CAUTION 1 About the setting of Hyper Threading Technology please check page 22 2 Please check the table below for the memory support frequency and its corresponding CPU FSB frequency CPU FSB Frequency Memory Support Frequency 800 DDR266 DDR320 DDR400 533 DDR266 DDR333 400 DDR266 When you use an FSB800 CPU on this motherboard it will run at DDR320 if you adopt a DDR333 memory module 3 While CPU overheat is detected the system will automat
30. sibility of such damages arising from any defect or error in the manual or product FC This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation ASRock Website http www asrock com Contents 1 Introduction essen 5 1 1 Package Contents 5 1 2 Specifications cere th deeds 6 1 3 Motherboard Layout eene 8 1 4 ASROCK T O Pl s M secte ta 9 Zinaa eoa aaa A R 10 Pre installation Precautions 10 2 1 CPU Installation eee 11 2 2 Installation of CPU Fan and Heatsink ssec 11 2 3 Installation of Memory Modules DIMM 12 2 4 Expansion Slots PCI and AGP Slots 13 2 5 Jumpers Setup eee 14 2 6 Onboard Headers and Connectors 15 2 7 Serial ATA SATA Hard Disks Installation 18 3 BIOS SETUP UTILITY esses 19 3 1 introducti sasssa irni aanle iiaae lara ria aaea akna RATIS 19 3 1 1 BIOS Menu Bar see 19 3 1 2 Navigation Keys 20 3 2 Mairi Screen nant em ie nn sine tre 20 3 3 Advanced Screen sse 21 8 8 1 CPU Configuration 21 8 3 2 Chipset Configuration cee eeeeeeeeeeeeteeeeeees 22 8 8 3 ACPI Configuration 24 3 3 4 IDE Configuration eee 25 8 8 5 PCIPn
31. umpers Do NOT place jumper caps over these headers and connectors Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard the red striped side to Pin1 FDD connector 33 pin FLOPPY1 see p 8 No 20 Pint Note Make sure the red striped side of the cable is plugged into Pin1 side of the connector Primary IDE connector Blue Secondary IDE connector Black 39 pin IDE1 see p 8 No 8 39 pin IDE2 see p 8 No 7 connect the blue end Cc T D connect the black end to the motherboard s x to the IDE devices 80 conductor ATA 66 100 cable Note If you use only one IDE device on this motherboard please set the IDE device as Master Please refer to the instruction of your IDE device vendor for the details Besides to optimize compatibility and performance please connect your hard disk drive to the primary IDE connector IDE1 blue and CD ROM to the secondary IDE connector IDE2 black Serial ATA Connectors These two Serial ATA SATA SATA1 see p 8 No 14 SATA2 connectors support SATA data SATA2 see p 8 No 13 cables for internal storage SATA1 devices The current SATA interface allows up to 1 5 Gb s data transfer rate Serial ATA SATA Either end of the SATA data cable Data Cable can be connected to the SATA hard disk or the SATA connector on the motherboard 151 I 16 Serial ATA SATA si Power Cable 4 Optional connect to the SA
32. uration of your chassis to en sure that the motherboard fits into it Pre installation Precautions Take note of the following precautions before you install motherboard com ponents or change any motherboard settings 1 Unplug the power cord from the wall socket before touching any component 2 To avoid damaging the motherboard components due to static electricity NEVER place your motherboard directly on the carpet or the like Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components 3 Hold components by the edges and do not touch the ICs 4 Whenever you uninstall any component place it on a grounded anti static pad or in the bag that comes with the component Before you install or remove any component ensure that the power is switched off or the power cord is detached from the power supply Failure to do so may cause severe damage to the motherboard peripherals and or components 2 1 Step 1 Step 2 Step 3 A Step 4 CPU Installation Unlock the socket by lifting the lever up to a 90 angle Position the CPU directly above the socket such that its marked corner matches the base of the socket lever Carefully insert the CPU into the socket until it fits in place The CPU fits only in one correct orientation DO NOT force the CPU into the socket to avoid bending of the pins When the CPU is in place press it firmly on the socket while you push down

ASRock P4i48-M motherboard user manual

Contents

Download Pdf Manuals

Related Search

Related Contents