Home

D-LINK DWL-2700AP Manual

1. Authentication WPA Personal v PassPhrase Settings Cipher Type AUTO v Group Key Update Interval 1800 Sec passPhrase OOOO OE Apply Cipher Type When you select WPA Personal WPA2 Personal or WPA Auto Personal you must select AUTO AES or TKIP from the pull down menu Select the interval during which the group key will be valid Broun gei opiate The default value of 1800 is recommended nterval Enter a passphrase The passphrase is an alpha numeric password between 8 and 63 characters long The password can include symbols amp _ and spaces Make sure you enter this key exactly the same on all other wireless clients PassPhrase D Link DWL 2700AP User Manual 22 WDS with AP Mode D Link 802 11G Outdoor Wireless AP Bridge Home X Tool Configuration v System Bl Logout Help DAL 2700AP Basic Settings a less Wireless Band IEEE802 119 LAN S Advanced Settings Mode WDS with AP v age Status Wireless Network Name SSID dlink SSID Broadcast Enable v Channel 1 2 412 GHz Auto Channel Scan WDS with AP Remote AP MAC Address il al EN sl Site Survey Type CH Signal BSSID Security Authentication Open System Open System Key Settings Encryption 1 Shared Key Me O Disable Open System Shared Key Key Type HEX WPA Personal WPA2 Personal Valid Key W
2. Introduction The DWL 2700AP a reliable high performance wireless outdoor solution is an ideal addition to business networks seeking to extend wireless signal coverage With the DWL 2700AP bandwidth intensive applications like graphics or multimedia will benefit significantly because large files are able to move across the network quickly The DWL 2700AP is capable of operating in one of 3 different modes to meet your wireless networking needs The DWL 2700AP can operate as an access point or in WDS Wireless Distribution System with AP or in WDS mode Use less wiring enjoy increased flexibility save time and money with PoE Power over Ethernet With PoE the DWL 2700AP shares power and data over the CAT5 cable making the setup of your network less expensive and more convenient An ideal solution for quickly creating and extending a wireless local area network WLAN in offices or other workplaces trade shows and special events the DWL 2700AP provides data transfers at up to 54Mbps when used with other D Link Air Premier products The 802 119 standard is backwards compatible with 802 11b devices WPA is offered in two flavors Enterprise used for corporations and Personal used for home users WPA Personal and WPA2 Personal is directed at home users who do not have the server based equipment required for user authentication The method of authentication is similar to WEP because you define a Pre Shared Key on the wir
3. 5 Why does my wireless connection keep dropping Antenna Orientation Try different antenna orientations for the DWL 2700AP Try to keep the antenna at least 6 inches away from the wall or other objects If you are using 2 4GHz cordless phones X 10 equipment or other home security systems ceiling fans and lights your wireless connection will degrade dramatically or drop altogether Try changing the channel on your router access point and wireless adapter to a different channel to avoid interference Keep your product away at least 3 6 feet from electrical devices that generate RF noise like microwaves monitors electric motors etc Why can t I get a wireless connection If you have enabled encryption on the DWL 2700AP you must also enable encryption on all wireless clients in order to establish a wireless connection Make sure that the SSID on the router and the wireless client are exactly the same If they are not wireless connection will not be established Move the DWL 2700AP and the wireless client into the same room and then test the wireless connection Disable all security settings Turn off your DWL 2700AP and the client Turn the DWL 2700AP back on again and then turn on the client Make sure that all devices are set to Infrastructure mode Check that the LED indicators are indicating normal activity If not check that the AC power and Ethernet cables are firmly connected Check that the IP address
4. Select 64 bit 128 bit or 152 bits Valid Key Select the 1st through the 4th key to be the active key First through Fourth Input up to four keys for encryption You will select one of these keys in keys the valid key field Hexadecimal digits consist of the numbers 0 9 and the letters A F ASCII American Standard Code for Information Interchange is a code for representing English letters as numbers 0 127 D Link DWL 2700AP User Manual 25 WPA WPA2 Personal Encryption D Link 802 11G Outdoor Wireless AP Bridge A Home Tool Configuration So System Bi Logout Help 2 DWL 27004P Ge Basic Settings Pl ser Wireless Band IEEE802 119 LAN H E Advanced Settings Mode WDS with AP v P Status Wireless Network Name SSID dlink SSID Broadcast Enable v Channel 1 12 412 GHz Auto Channel Scan WDS with AP Remote AP MAC Address EEE ORRE HE EE ih 6 Ue 8 Site Survey Scan Type CH Signal SSID Security Authentication WPA Personal PassPhrase Settings Cipher Type AUTO w Group Key Update Interval 1800 Sec PassPhrase Cipher Type When you select WPA Personal WPA2 Personal or WPA Auto Personal you must select AUTO or AES from the pull down menu Group Key Update Select the interval during which the group key will be valid The default value Interval of 1800 is recommended PassPhrase Enter a passphrase The passphrase is an alpha numeric password betw
5. 10 Wireless Installation Considerations The D Link wireless point lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network Keep in mind however that the number thickness and location of walls ceilings or other objects that the wireless signals must pass through may limit the range Typical ranges vary depending on the types of materials and background RF radio frequency noise in your home or business The key to maximizing wireless range is to follow these basic guidelines 1 Keep the number of walls and ceilings between the D Link router and other network devices to a minimum each wall or ceiling can reduce your adapter s range from 3 90 feet 1 30 meters Position your devices so that the number of walls or ceilings is minimized 2 Be aware of the direct line between network devices A wall that is 1 5 feet thick 5 meters at a 45 degree angle appears to be almost 3 feet 1 meter thick At a 2 degree angle it looks over 42 feet 14 meters thick Position devices so that the signal will travel straight through a wall or ceiling instead of at an angle for better reception 3 Building Materials make a difference A solid metal door or aluminum studs may have a negative effect on range Try to position access points wireless routers and computers so that the signal passes through drywall or open doorways Materials and objects such as glass steel me
6. 44 WDS Information D Link 802 11G Outdoor Wireless AP Bridge Home Tool Configuration lt gt Syste BD Logout Hei 2 DVYL 2700 amp P Basic Settings P Advanced Settings WDS Information Station association with 11B G 0 e Status 530 MAC Bana Authentication Signal Channel Device Information A Indication B Client Information A WDS Information i Stats A Log MAG Displays the MAC address of the client Band Displays the wireless band the client is connected on Authentication Displays the type of authentication being used Signal Displays the strength of the clients signal Channel Displays the wireless channel being used D Link DWL 2700AP User Manual 45 WLAN 802 11G Traffic Statistics D Link 802 11G Outdoor Wireless AP Bridge d Home Tool Configuration lt gt Pl Logout Hei 2 DVYL 2700 amp P HP Basic Settings ES Advanced Settings Throughput f Status Transmit Success Rate gt Device Information Transmit Retry Rate oan Receive Success Rate Client Information 8 A WDS Information Receive Duplicate Rate Stats RTS Success Count Log RTS Failure Count Transmitted Frame Count Transmitted Frame Count Multicast Transmitted Frame Count Transmitted Error Count Transmitted Total Retry Count Transmitted Multiple Retry Count Received Frame Count Received Frame Count Multicast Received Frame Count Received Frame FCS Error Count Received Frame
7. Click Delete next to a MAC address to remove it from the list D Link DWL 2700AP User Manual 38 Wireless MAC ACL D Link 802 11G Outdoor Wireless AP Bridge Home Tool Configuration v gt System Pi Logout Help 2 DVYL 270DAP a p Basit Settings i z Weg Wireless Band IEEE802 11g ge Advanced Settings Access Control Disable alge MAC Address IT gt Grouping gt Mutti SSID e DHCP Server ID MAC Address Delete Dynamic Pool Settinc Static Pool Setting Current IP Mapping L 5 Filters Ethernet MAC ACL Wireless MAC ACL Wireless IP ACL WLAN Partition EW E iY Du y vu EIJ RY Kl E ao af 2 wo Wireless Band IEEE 802 119 Access Control Select Off to disable MAC address filtering Select Accept to allow association between the DWL 2700AP and the MAC addresses listed Select Reject to reject devices with the MAC addresses listed MAC Address Enter the MAC address you want to include in the Access Control List and click Apply MAC Address List MAC addresses added to the Access Control List will appear in this list Click Delete next to a MAC address to remove it from the list D Link DWL 2700AP User Manual 39 Wireless IP ACL D Link 802 11G Outdoor Wireless AP Bridge Home X Tool E Configuration System HA Logout _ Help ST Dud 2700AP Basic Settings me Wireless Access Control Disable v B LAN Ef Advanced Settings IP
8. Client Information A WDS Information Download Configuration File Load settings to Local Hard Drive gt Log Settings Upload File Click Browse to locate a previously saved configuration file on your local computer After selecting the file click Upload to apply the configuration settings to the DWL 2700AP Download Click Download to save the current DWL 2700AP configuration to your Configuration File local computer D Link DWL 2700AP User Manual 52 Select File Choose file Amy Music My Recent Zu Pictures Documents My Received Files iz my Web Sites Desktop My Documents My Computer My Network File name z Places Files of type fan Files D v Cancel When you click Browse in the previous screen the dialog box shown above appears Select the file you wish to download and click Open File Download Do you want to open or save this file E Name dwl2700 dcf Type Unknown File Type From 192 168 00 50 Always ask before opening this type of file harm your computer If you do not trust the source do not open or wi While files from the Internet can be useful some files can potentially save this file What s the risk When this dialog box appears click Save and select a location to save the configuration file D Link DWL 2700AP User Manual 53 D Link Home X Tool v Configuration System Bl Logout
9. EE e ele EE ee eer eee 48 Gp Eee ge sj REE 49 Change NN 49 CAINS SONG E 49 Console Settings Lure Folden 49 SNMP NGS eneen ashen eenen 49 Firmware and SSL Certification Upload cccccccceeeeeessssseeeesssseeeees 51 Configuration File Upload and Download nne 52 Select TE 53 VRANG 54 SVENE get ee 55 SEE ED 5 EE errr teens 55 Restore to Factory Settings sneden tene eeben 55 Using the ERNA 56 le Ee du Le A 59 D Link DWL 2700AP User Manual Technical SpecificatiOnS snnnxnnrnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnneennnnnnnnnnnnnnnnnnnuenennnnnnnnnvnnnnnn 62 Contacting Technical SUPPOrE sein anseneeeeideennnnededeenkenennnhikkaadsenenneens eneen 64 Ke TE EE NE 65 PREG SU NE 70 D Link DWL 2700AP User Manual Package Contents Note Using a power supply with a different voltage rating than the one included with the DGL 4500 will cause damage and void the warranty for this product D Link DWL 2700AP User Manual System Requirements D Link DWL 2700AP User Manual Computer with the following e Windows Macintosh or Linux based operating system An installed Ethernet adapter Browser Requirements Internet Explorer 6 0 or higher e Mozilla 1 7 12 or higher e Firefox 1 5 or higher e Safari 1 0 or higher with Java 1 3 1 or higher e Flock 0 7 14 or higher e Opera 6 0 or higher Windows Users Make sure you have the latest version of Java installed Visit www java com to download the latest version
10. Link 802 11G Outdoor Wireless AP Bridge Home Tool v Configuration So System ee Help 2 DWL 27004P zi Le Basic Settings gt Wireless Balance v LAN Load Disable v Advanced Settings User Limit 0 64 10 gt Performance i en gt Grouping Link Integrate Disable gt Mutti SSID ts DHCP Server ts Filters Status Load Balance Load Balancing allows you to balance and share the wireless net work traffic and clients using multiple DWL 2700APs Select Enable or Disable User Limit Sets the maximum amount of users allowed 0 64 Link Integrate If the Ethernet connection between the LAN and the DWL 2700AP is disconnected the Link Integrate option will cause the wireless segment associated with the AP to be disconnected from the AP Select Enable or Disable D Link DWL 2700AP User Manual Multi SSID Settings D Link 802 11G Outdoor Wireless AP Bridge Home Tool Configuration v gt System Bl Logout Help DVL 2700AP il p Basic Settings aa C Enable Multi ssiD CJ Enable VLAN State H Advanced Settings Wireless Settings 8 Performance Band EEE802 119 Grouping Multi SSID Index Primary SSID ime DHCP Server Wireless Network Name SSID Es Filters Status SSID Broadcast Enable Security sone VLAN ID fi o Key Settings Key Type He Key Size 54 Bits Key 1 0000000000 Index Band E
11. address C Performance gt Grouping F Mutti SSID Ge DHCP Server ID IP address Delete gt Dynamic Pool Settinc 8 H Static Pool Setting Current IP Mapping L Ef Filters Ethernet MAC ACL B Wireless MAC ACL B Wireless IP ACL WLAN Partition H B Status Access Control Select Off to disable IP address filtering Select Accept to allow association between the DWL 2700AP and the IP addresses listed Select Reject to reject devices with the IP addresses listed IP Address Enter the IP address you want to include in the Access Control List and click Apply IP Address List IP addresses added to the Access Control List will appear in this list Click Delete next to an IP address to remove it from the list D Link DWL 2700AP User Manual 40 D Link g Home Tool e EL Be P Statu DAL 2700AP Ge Basic Settings he Wireless AN LG Ae Advanced Settings Performance H Grouping Mutti SSID Bg DHCP Server 2 Dynamic Pool Setting Static Pool Setting Current IP Mapping L ilters Ethernet MAC ACL Wireless MAC ACL Wireless IP ACL i WLAN Partition 5 Wireless Band Internal Station Connection Ethernet to WLAN Access WLAN Partition Settings MW Configuration Wireless Band Internal Station Connection Ethernet to WLAN Access IEEE 802 119 S System 802 11G Outdoor Wireless AP Bridge Bi Logout Gi Help IEEE80
12. community string D Link DWL 2700AP User Manual 50 Firmware and SSL Certification Upload D Link Home X Tool Dr 2700AP B Basic Settings H B Advanced Settings J Status Device Information Indication gt Client Information A WDS Information B Stats ES Log gt View Log gt Log Settings 802 11G Outdoor Wireless AP Bridge v Configuration v gt System Bi Logout Gi Help Update Firmware From Local Hard Drive Firmware Version v3 10 Upload Firmware From File Update SSL Certification From Local Hard Drive Upload Certificate From File Upload Key From File Browse Upload Upload Firmware After downloading the most recent version of firmware for the DWL 2700AP from http support dlink com to your local computer use the Browse button to locate the firmware file on your computer Click Upload to update the firmware version Upload SSL Click Browse to locate the SSL Certification file on your local computer Certification After selecting and opening the file click Upload to upload the file to the DWL 2700AP D Link DWL 2700AP User Manual 51 Configuration File Upload and Download D Link 802 11G Outdoor Wireless AP Bridge d Home X Tool E Configuration System JET GE DAL 2700AP i d ker Basic Settings d f k Advanced Settings Upload Configuration File r Upload File Device Information gt Indication gt
13. ke II M 2 ge Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights Version 2 10 August 23 2007 D Link DWL 2700AP User Manual 70
14. original purchase point based on its return policy In case the return policy period has expired and the product is within warranty the customer shall submit a claim to D Link as outlined below e The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance in sufficient detail to allow DLink to confirm the same along with proof of purchase of the product such as a copy of the dated purchase invoice for the product if the product is not registered e The customer must obtain a Case ID Number from D Link Technical Support at 1 877 453 5465 who will attempt to assist the customer in resolving any suspected defects with the product If the product is considered defective the customer must obtain a Return Material Authorization RMA number by completing the RMA form and entering the assigned Case ID Number at https rma dlink com e After an RMA number is issued the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit and the RMA number must be prominently marked on the outside of the package Do not include any manuals or accessories in the shipping package DLink will only replace the defective portion of the product and will not ship back any accessories e The customer is responsible for all in bound shipping charges to D Link No Cash on Delivery COD is allowe
15. that the hardware portion of the D Link product described below Hardware will be free from material defects in workmanship and materials under normal use from the date of original retail purchase of the product for the period set forth below Warranty Period except as otherwise stated herein e Hardware excluding power supplies and fans One 1 year e Power supplies and fans One 1 year e Spare parts and spare kits Ninety 90 days The customer s sole and exclusive remedy and the entire liability of D Link and its suppliers under this Limited Warranty will be at D Link s option to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund the actual purchase price paid Any repair or replacement will be rendered by D Link at an Authorized D Link Service Office The replacement hardware need not be new or have an identical make model or part D Link may at its option replace the defective Hardware or any part thereof with any reconditioned product that D Link reasonably determines is substantially equivalent or superior in all material respects to the defective Hardware Repaired or replacement hardware will be warranted for the remainder of the original Warranty Period or ninety 90 days whichever is longer and is subject to the same limitations and exclusions If a material defect is incapable of correction or if D Link determines that it is not practical to repa
16. the phone number that you want to dial Country region nied States 1 Area code 714 Phone number Connect using Jett v 5 Configure the Port Settings COM1 Properties Port Settings Bits per second Data bits Parity Stop bits Flow control Note Your terminal emulation must be set to 9600 bits per second D Link DWL 2700AP User Manual 57 6 Enter Login Name and Password Access Point Hyper Terminal File Edit View Call Transfer Help DS 5 28 wireless access point starting Auto Channel Scan selected 2412 MHz channel 1 wlanl Ready Ready Starting web server Server is initializing Default Certificate and Private Key Decode Private Key with RSA Success Certificate Loaded Successfully Server is ready 0 D link Corp Access Point login admin Password Atheros Access Point Rev 4 1 2 56 D link Corp Access Point wlanl gt _ Connected 0 02 30 Auto detect 9600 8 N 1 Once logged in you will be able to run configuration commands from the command line prompt D Link DWL 2700AP User Manual 58 Troubleshooting This Chapter provides solutions to problems that can occur during the installation and operation of the DWL 2700AP Wireless Access Point We cover various aspects of the network setup including the network adapters Please read the following if you are having problems Note It
17. the provided serial console cable to the console port on the DWL 2700AP and the other to an available serial port on the PC you wil use to connect to the device 2 Run HyperTerminal on the PC Goto the Start Menu e Select All Programs e Select Accessories e Select Communications e Select HyperTerminal 3 Enter a New Connection name D Link DWL 2700AP User Manual Accessibility gt fa Co ions ICH Entertainment System Tools VJ Address Book 15 Calculator ES Command Prompt B Notepad WY Paint Program Compatibility Wizard Internet Internet Explorer Y Paint ei HyperTerminal EB WinRAR Windows Catalog Windows Update IC Administrative Tools D Link ei Games ICH Mozilla Firefox ei Startup ICH Winrar internet Explorer s gt Remote Assistance buet 33 windows Messenger Connection Description SL New Connection Set Program Access and Defaults Be Log Off Turn Off Computer 4 untitled Paint 3 synchronize Tour Windows XP EG Windows Explorer E windows Movie Maker A Wordpad Enter a name and choose an icon for the connection Name Access Point network Connections 2 Network Setup Wizard E New Connection Wizard F Remote Desktop Connection Icon 56 4 Select the appropriate COM port Connect To D Access Point Enter details for
18. worker efficiency Low Implementation Costs WLANs are easy to set up manage change and relocate Networks that frequently change can benefit from WLANs ease of implementation WLANs can operate in locations where installation of wiring may be impractical Installation and Network Expansion Installing a WLAN system can be fast and easy and can eliminate the need to pull cable through walls and ceilings Wireless technology allows the network to go where wires Cannot go even outside the home or office Inexpensive Solution Wireless network devices are as competitively priced as conventional Ethernet network devices The DWL 2700AP saves money by providing multi functionality configurable in one of three different modes Scalability WLANs can be configured in a variety of ways to meet the needs of specific applications and installations Configurations are easily changed and range from Peer to Peer networks suitable for a small number of users to larger Infrastructure networks to accommodate hundreds or thousands of users depending on the number of wireless devices deployed D Link DWL 2700AP User Manual 9 Standards based Technology The DWL 2700AP Wireless Access Point utilizes the 802 11b and the 802 119 standards The IEEE 802 119 standard is an extension of the 802 11b standard It increases the maximum wireless signal rate of up to 54Mbps within the 2 4GHz band utilizing OFDM technology This means that in most environmen
19. 2 11g Enable Enable Enabling this feature allows wireless clients to communicate with each other If this feature is disabled wireless stations on the selected band are not allowed to exchange data through the access point Enabling this feature allows Ethernet devices on the LAN to communicate with wireless clients on the WLAN If this feature is disabled all data from Ethernet devices to wireless clients is blocked Wireless devices can still send data to Ethernet devices D Link DWL 2700AP User Manual 41 Status Device Information D Link Home Tool Configuration gt System P Logout Help DVWL 27004P D P Basic Settings H Advanced Settings A Device Information B Indication Client Information Ethernet Gateway SSID Channel 802 11G Outdoor Wireless AP Bridge Firmware Version v3 10 CS Status Ethernet MAC Address 00 15 e9 c9 00 50 i WLAN1 MAC Address Primary 00 15 e9 c9 00 50 Secondary 00 15 e9 c9 00 51 00 15 e9 c9 00 57 i WDS Information Get IP From Manual ig Stats IP address 192 168 0 50 SP Log Subnet Mask 255 255 255 0 0 0 0 0 Wireless 802 119 dlink 1 Data Rate Auto Security Level Open System Encryption Disabled Device Information This window displays the configuration settings of the DWL 2700AP including the firmware version and device MAC address D Link DWL 2700AP User Manual 42 Indication 802 11G Outdoor Wireles
20. 277 7mm e W 6 10 inches 155mm e H 1 77 inches 45mm Warranty e 1 Year D Link DWL 2700AP User Manual 63 Contacting Technical Support U S and Canadian customers can contact D Link technical support through our web site or by phone Before you contact technical support please have the following ready e Model number of the product e g DWL 2700AP e Hardware Revision located on the label on the bottom of the device e g rev A1 e Serial Number s n number located on the label on the bottom of the device You can find software updates and user documentation on the D Link website as well as frequently asked questions and answers to technical issues For customers within the United States Phone Support 877 354 6555 Internet Support http support dlink com For customers within Canada Phone Support 877 354 6560 Internet Support http support dlink com D Link DWL 2700AP User Manual 64 Warranty Subject to the terms and conditions set forth herein D Link Systems Inc D Link provides this Limited Warranty e Only to the person or entity that originally purchased the product from D Link or its authorized reseller or distributor and e Only for products purchased and delivered within the fifty states of the United States the District of Columbia U S Possessions or Protectorates U S Military Installations or addresses with an APO or FPO Limited Warranty D Link warrants
21. 92 168 606 586 Pinging 192 168 5 with 32 bytes of data Reply from 192 168 0 50 bytes 32 time lt ims TTL 64 Reply from 192 168 0 50 bytes 32 time lt ims TTL 64 Reply from 192 168 0 50 bytes 32 time lt ims TTL 64 Reply from 192 168 0 50 bytes 32 time lt ims TTL 64 Ping statistics for 192 168 5 Packets Sent 4 Received 4 Lost z loss gt Approximate round trip times in milli seconds Minimum ms Maximum ms Average ns F NDocuments and Settings lah3 gt _ D Link DWL 2700AP User Manual 59 2 The wireless client cannot access the Internet in the Infrastructure mode Make sure the wireless client is associated and joined with the correct access point To check this connection Right click on the Local Area Connection icon in the taskbar gt select View Available Wireless Networks The Connect to Wireless Network screen will appear Please make sure you have selected the correct available network as shown in the illustrations below Disable Status Repair View Available Wireless Networks Open Network Connections Connect to Wireless Network PIX The following network s are available To access a network select it from the list and then click Connect Available networks alan dan E default t na If you are having difficulty connecting to a network click Advanced m Check that the IP address assigned to the wireless adapter is within the sa
22. D SET FORTH ABOVE EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN THE ENTIRE RISK AS TO THE QUALITY SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT D Link DWL 2700AP User Manual 67 Limitation of Liability TO THE MAXIMUM EXTENT PERMITTED BY LAW D LINK IS NOT LIABLE UNDER ANY CONTRACT NEGLIGENCE STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT INCONVENIENCE OR DAMAGES OF ANY CHARACTER WHETHER DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL INCLUDING BUT NOT LIMITED TO DAMAGES FOR LOSS OF GOODWILL LOSS OF REVENUE OR PROFIT WORK STOPPAGE COMPUTER FAILURE OR MALFUNCTION FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D LINK S PRODUCT IS CONNECTED WITH LOSS OF INFORMATION OR DATA CONTAINED IN STORED ON OR INTEGRATED WITH ANY PRODUCT RETURNED TO D LINK FOR WARRANTY SERVICE RESULTING FROM THE USE OF THE PRODUCT RELATING TO WARRANTY SERVICE OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY EVEN IF D LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPAIR REPLACEMENT OR REFUND OF THE DEFECTIVE OR NONCONFORMING PRODUCT THE MAXIMUM LIABILITY OF D LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY THE FOREGOING EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES
23. DIUS server required and encryption of data is upgraded with the Advanced Encryption Standard AES Select WPA Auto Enterprise to allow the client to either use WPA Enterprise or WPA2 Enterprise Select WPA Auto Personal to allow the client to either use WPA Personal or WPA2 Personal D Link DWL 2700AP User Manual 18 WEP Encryption D Link 802 11G Outdoor Wireless AP Bridge Home Tool e m Configuration v s System Logout Help ST Dat 2700AP d Basic Settings i ag Wireless Wireless Band IEEE802 119 iE LAN i P Advanced Settings Mode Access Point v 7 Fr Status Wireless Network Name SSID dink SSID Broadcast Enable v Channel 1 2 412 GHz Auto Channel Scan Authentication Open System v Key Settings Encryption O Disable Enable Key Type HEX wi Key Size 64 Bits e valid Key First First Key D ZONE Second Key mo Third Key Lessssssss Fourth Key mor Encryption Select Disabled or Enabled Disabled is selected here Key Type Select HEX or ASCII Key Size Select 64 bit 128 bit or 152 bits Valid Key Select the 1st through the 4th key to be the active key First through Fourth Input up to four keys for encryption You will select one of these keys in keys the valid key field Hexadecimal digits consist of the numbers 0 9 and the letters A F ASCII American Standard Code for Information Interchange is a co
24. DWL 2700AP Release 2 10 Outdoor AP Bridge Wireless G Outdoor AP Bridge User Manual Table of Contents Product OV e 5 Package GMN EE ET EE 5 System Requirements RER TE 6 MINN 7 EE 8 Wireless BASICS ad 9 Standards based Technology den 10 Wireless Installation ConsideratlOfS onmens seeden 11 Getting Started vs 12 Connecting to a Power over Ethernet Network AAA 13 Configuration sosise Eaa aa aE ee 14 Web based Configuration Utility oreert eenn 14 Save and Activate EEE RE 15 Wireless Modes Lave EENEN EEEE EEN aaa 16 FN 17 Wireless Settings nennen eend 17 Access Felnt OCS EEEE 17 VPT IN 19 802 1 RADIUS ET 20 WPA WPA2 Enterprise Encrvptton eereenenenveeennnnnn 21 WENN PAZ Personal Encryption savvcornashasntansaniacasndnitonnenansieanansanternddesss 22 WDS with AP MODS EE 23 WEE TN 25 WPA WPA2 Personal Encryption eee 26 VPS BL 27 WEP ETNA 29 WPAMWPA Personal Encryption marsen metende dadendstatnnnne 30 En 31 ee 31 BE Fel ll 32 Advanced es e eee a er ee ee 33 FT TE 33 GEN tees 33 Deeg 33 D Link DWL 2700AP User Manual WMM ME 33 TEMP ON vu 33 Antenna Diversity TE 33 AP Grouping EAN ve 35 Coad Balance NN NR 35 leet 35 Multi SSID Settings eege dere 36 EEE ERE 38 Ethernet MAC ACL ER ENEE 38 Wireless MAC ACL PE ET NE 39 TE SG EE ettr eee 40 WLAN Partition Settings arver 41 TT 42 Device Information E 42 le ee EE 43 EIE uge dage 44 WDS INGEN nede aksene 45 UR ERT e 46 clo E 47 View on 47 System
25. Duplicate Count ACK RCV failure Count WEP Frame Error Count WEP Excluded Frame Count WEP ICY Error Count d II WLAN 802 119 Traffic Statistics This page displays statistics for data throughput transmitted and received frames and WEP frame errors for the 802 11g wireless network D Link DWL 2700AP User Manual D Link 802 11G Outdoor Wireless AP Bridge Home Tool M Configuration System BD Logout M Help 2 DVYL 2700AP 4 8 Basic Settings EE eee ee il B Advanced Settings Total Log 100 us Device Information desi Received Disassoc WLAN 1 11G STA 00 1 Client Information 1 95 8c ef f9 WDS Information Association 11G STA 00 11 95 8c ef f9 associated with WLAN1 SSID dlink2 Received Deauth WLAN 1 11G STA 00 11 i 95 8c eff9 reason code 3 i BB Log Settings Received Disassoc WLAN 1 11G STA 00 1 1 95 8c eff9 Association 11G STA 00 11 95 8c ef fa associated with WLAN1 SSID dlink Received Deauth WLAN 1 11G STA 00 11 95 8c eff9 reason code 3 Received Disassoc WLAN 1 11G STA 00 1 1 95 8c ef fd Association 11G STA 00 11 95 8c ef fa associated with WLAN1 SSID dlink2 100 0 day 0 11 09 Web logout from 192 168 0 100 0 day 0 01 05 System Web login successfully from 192 168 0 100 0 day 0 00 10 AP warm start with fiw version v3 00 0 day 0 00 10 Wireless WLAN1 Normal AP ready 0 day 3 05 42 AP reboot by MANUAL REBOOT N dav AAA SYSTFM fartnmv defialt set View Log The lo
26. EXPRESS IMPLIED OR STATUTORY Governing Law This Limited Warranty shall be governed by the laws of the State of California Some states do not allow exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the foregoing limitations and exclusions may not apply This Limited Warranty provides specific legal rights and you may also have other rights which vary from state to state Trademarks D Link is a registered trademark of D Link Corporation D Link Systems Inc Other trademarks or registered trademarks are the property of their respective owners Patent Pending Copyright Statement No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from D Link Corporation D Link Systems Inc as stipulated by the United States Copyright Act of 1976 and any amendments thereto Contents are subject to change without prior notice Copyright 2007 by D Link Corporation D Link Systems Inc All rights reserved FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio fre
27. Help 2 DVYL 2700AP Ip kor Basic Settings P Advanced Settings Ae Status Device Information Indication gt Client Information A WDS Information gt Stats Log View Log Log Settings SNTP NTP Information SNT NTP Server IP Address SNTP NTP Time Zone Daylight Saving Time SNTP Settings 802 11G Outdoor Wireless AP Bridge SNTP NTP Information SNTPINTP Server IP GMT Greenwich Mean Time Dublin Edinburgh Lisbon SNTPINTP Time Zone London Local Time SNTP NTP Setting SNTP NTP Server IP SNTP NTP Time Zone GMT Greenwich Mean Time Dublin Edinburgh Lisbon London ze Daylight Saving Time TT Enable Displays the current SNTP NTP settings Enter the SNTP NTP server IP address Select your correct Time Zone Check the box to Enable Daylight Saving Time D Link DWL 2700AP User Manual 54 System Settings D Link 802 11G Outdoor Wireless AP Bridge Home Xl Tool Configuration 5 System Bi Logout MW Help DAL 2700AP Basic Settings fb Advanced Settings Status Apply Settings and Restart Restore to Factory Default Settings Click Restart to restart the DWL 2700AP Click Restore to restore the DWL 2700AP back to factory default settings D Link DWL 2700AP User Manual 59 Using the Console Port You can connect to the DWL 2700AP console port to configure device settings via the command line 1 Connect one end of
28. Limit Administrator IP 1 Limit Administrator IP 2 Login Settings User Name Old Password New Password Confirm New Password D Link DWL 2700AP User Manual Administrator Settings 802 11G Outdoor Wireless AP Bridge M Configuration v Bi Logout iW Help Limit Administrator IP C Limit Administrator IP 1 Limit Administrator IP 2 Login Settings User Name Old Password New Password Confirm New Password Console Settings Status Console Protocol Enable Telnet OSSH Timeout 1Min v SNMP Settings Status M Enable Public Community String Private Community String Check the box to enable the feature Enter the IP address that the administrator will be allowed to log in from Enter a secondary IP address that the administrator will be allowed to log in from Enter a user name The default is admin When changing your password enter the old password here When changing your password enter the new password here Confirm your new password here 49 Console Settings Status Status is Enabled by default Uncheck the box to disable the console Console Protocol Select the type of protocol you would like to use Telnet or SSH SNMP Settings Status Status is Enabled by default Uncheck the box to disable the SNMP functions Public Community String Enter the public SNMP community string Private Community String Enter the private SNMP
29. N m Wireless Wireless Band B LAN f Advanced Settings Mode SSID Broadcast Channel Authentication Cipher Type RADIUS Server RADIUS Port RADIUS Secret Accounting Mode Accounting Server Accounting Port H Status Wireless Network Name SSID 802 11G Outdoor Wireless AP Bridge gt System Bi Logout MW Help IEEE802 119 Access Point ze E nable w 1 2 412 GHz Auto Channel Scan WPA Enterprise i RADIUS Server Settings AUTO ze 1812 Disable Group Key Update Interval 1800 Sec el Po Cipher Type When you select WPA Enterprise WPA2 Enterprise or WPA Auto Enterprise you must select AUTO AES or TKIP from the pull down menu Group Key Update Select the interval during which the group key will be valid 1800 is the Interval recommended value A lower interval may reduce transfer data rate RADIUS Server Enter the IP address of the RADIUS server RADIUS Port Enter the RADIUS port RADIUS Secret Enter the RADIUS secret D Link DWL 2700AP User Manual 21 WPA WPA2 Personal Encryption gg Home Tool Configuration P Logout Help DAL 2700AP _ ze Basic Settings E Wireless Wireless Band IEEE802 119 gt LAN B Advanced Settings Mode Access Point v f Status Wireless Network Name SSID dlink SSID Broadcast Enable v Channel 2 412 GHz Auto Channel Scan
30. PA Auto Personal First Key socccccece Second Key Lenessssss Fourth Key eeeeeeese0 nl In WDS with AP mode the DWL 2700AP wirelessly connects multiple networks while still functioning as a wireless AP WDS Wireless Distribution System allows access points to communicate with one another wirelessly in a standardized way It can also simplify the network infrastructure by reducing the amount of cabling required Basically the access points will act as a client and an access point at the same time Wireless Band IEEE 802 119 Mode WDS with AP is selected from the pull down menu SSID Service Set Identifier SSID is the name designated for a specific wireless local area network WLAN The SSID factory default setting is dlink The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network D Link DWL 2700AP User Manual 23 SSID Broadcast Enable or Disable SSID broadcast Enabling this feature broadcasts the SSID across the network Channel 6 is the default channel for IEEE 802 119 All devices on the network must share the same channel Note The wireless adapters will automatically scan and match the wireless setting Auto Channel Scan This option is unavailable in WDS with AP mode Enter the MAC addresses of the APs in your network that will serve as Remote AP MAG Address bridges to wirelessly connect multiple networks
31. Scan Click Scan to view available APs in your network that will serve as bridges Authentication Select Open System to communicate the key across the network Select Shared Key to limit communication to only those devices that share the same WEP settings Select Open System Shared Key to allow either form of data encryption Select WPA Personal WPA2 Personal or WPA Auto Personal to secure your network using a password and dynamic key changes No RADIUS server required Note WDS is not completely specified in WiFi or IEEE standards Communication with other vendor s access points is not guaranteed D Link DWL 2700AP User Manual 24 WEP Encryption D Link 802 11G Outdoor Wireless AP Bridge Home Tool Configuration Bi Logout Help DVYL 2700AP Basic Settings a Wireless Wireless Band IEEE802 119 LAN E Advanced Settings Mode WDS with AP v status Wireless Network Name SSID dlink SSID Broadcast Enable v Channel 1 2 412 GHz Auto Channel Scan WDS with AP Remote AP MAC Address Security Authentication Open System Key Settings Encryption ODisable Enable Key Type HEN ei Key Size 4 Bits wl Valid Key First wl First Key jesveseesen Third Key eoccccccce Fourth Key eocccccces Encryption Select Disabled or Enabled Disabled is selected here Key Type Select HEX or ASCII Key Size
32. WPA2 Personal or WPA Auto Personal you must select a cipher type Available options are Auto AES or TKIP Select the interval during which the group key will remain valid 1800 is the recommended value as a lower value may reduce the transfer rate The passphrase is an alpha numeric password that must be between 8 63 characters long The password can include symbols _ and spaces Make sure to enter the passphrase exactly the same on all wireless clients D Link DWL 2700AP User Manual Filters Ethernet MAG AGL D Link 802 116 Outdoor Wireless AP Bridge Home Tool Configuration e 5 Syste Bi Logout Help DWL 27004P a g Basic Settings gt gr Access Control Disable v ff Advanced Settings MAC Address PFG gt Performance C Apply Grouping Een po i gt Multi SSID Ge DHCP Server ID MAC Address Delete G Dynamic Pool Setting gt Static Pool Setting i Current IP Mapping L 4 9 Filters gt Ethernet MAC ACL gt Wireless MAC ACL gt Wireless IP ACL gt WLAN Partition m l Status Access Control Select Off to disable MAC address filtering Select Accept to allow association between the DWL 2700AP and the MAC addresses listed Select Reject to reject devices with the MAC address listed MAC Address Enter the MAC address you want to include in the Access Control List and click Apply MAG Address List MAC addresses added to the Access Control List will appear in this list
33. cm between the radiator amp your body This transmitter must not be co located or operating in conjunction with any other antenna or transmitter The availability of some specific channels and or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination The firmware setting is not accessible by the end user For detailed warranty information applicable to products purchased outside the United States please contact the corresponding local D Link office Industry Canada Notice This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation IMPORTANT NOTE Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body This device has been designed to operate with an antenna having a maximum gain of 2 dB Antenna having a higher gain is strictly prohibited per regulations of Industry Canada The required antenna impedance is 50 ohms D Link DWL 2700AP User Manual 69 Registration Register your product online at ttp support dlink com register PE nn
34. d Products sent COD will either be rejected by D Link or become the property of D Link Products shall be fully insured by the customer and shipped to D Link Systems Inc 17595 Mt Herrmann Fountain Valley CA 92708 D Link will not be held responsible for any packages that are lost in transit to D Link The repaired or replaced packages will be shipped to the customer via UPS Ground or any common carrier selected by D Link Return shipping charges shall be prepaid by D Link if you use an address in the United States otherwise we will ship the product to you freight collect Expedited shipping is available upon request and provided shipping charges are prepaid by the customer D Link DWL 2700AP User Manual 66 D Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements or for which an RMA number is not visible from the outside of the package The product owner agrees to pay D Link s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing requirements or that is determined by D Link not to be defective or non conforming What Is Not Covered The Limited Warranty provided herein by D Link does not cover Products that in D Link s judgment have been subjected to abuse accident alteration modification tampering negligence misuse faulty installation lack of reasonable care repair or service in any wa
35. de for representing English letters as numbers 0 127 D Link DWL 2700AP User Manual 19 802 1x RADIUS Security LA kW e P D Link 802 11G Outdoor Wireless AP Bridge Home X Tool Configuration gt System BD Logout Help DWL 27004P D Basic Settings vareless Wireless Band o gt LAN Advanced Settings Mode Access Point v a Status Wireless Network Name SSID dlink SSID Broadcast Enable v Channel 1 2 412 GHz Auto Channel Scan Authentication 802 1x v 802 1x Settings Encryption O Disable Enable WEP Key Type O Static Dynamic Key Type HE Key Size Valid Key First First Key Jesssssssss Second Key EES Third Key esseesess Fourth Key scccccoeee Cipher Type WEP wl RADIUS Sewer RADIUSPort 1812 RADIUS Secret Accounting Mode Disable w Accounting Server Accounting Port 1813 Cipher Type WEP is selected Group Key Update Select the interval during which the group key will be valid 1800 is the Interval recommended value A lower interval may reduce transfer data rate RADIUS Server Enter the IP address of the RADIUS server RADIUS Port Enter the RADIUS port RADIUS Secret Enter the RADIUS secret D Link DWL 2700AP User Manual WPA WPA2 Enterprise Encryption pn e D Link Home Tool Configuration e DAL 2700AP Ger Basic Settings E
36. een 8 and 63 characters long The password can include symbols amp _ and spaces Make sure you enter this key exactly the same on all other wireless clients D Link DWL 2700AP User Manual 26 WDS Mode D Link 802 11G Outdoor Wireless AP Bridge Home X Tool Configuration System BD Logout Help DVYL 2700AP D Basic Settings gt z Wireless wireless Band IEEE802 119 gt LAN 3 Advanced Settings Mode WDS v 5 f Status Wireless Network Name SSID dlink SSE SSID Broadcast Enable w Channel 1 2 412 GHz Auto Channel Scan WDS Remote AP MAC Address ie 2 3 4 Eh 6 E 8 Site Survey Type CH Signal BSSID Security Authentication Open System Key Settings Open System S T Opi Shared Key Typ Disablel open system Shared Key Key Type HEX WPA Personal d Bits v VWPA2 Personal Valid Key WPA Auto Personal First Key eeccccoces Second Key mum Third Key Leeseesee f Fourth Key mo In WDS the DWL 2700AP wirelessly connects multiple networks without functioning as a wireless AP Wireless Band IEEE 802 119 Mode WDS is selected from the pull down menu SSID Service Set Identifier SSID is the name designated for a specific wireless local area network WLAN The SSID factory default setting is default The SSID can be easily changed to connect to an existing wirele
37. eless router AP Once the pre shared key is confirmed and satisfied on both the client and access point then access is granted The encryption method used is referred to as the Temporal Key Integrity Protocol TKIP which offers per packet dynamic hashing It also includes an integrity checking feature which ensures that the packets were not tampered with during wireless transmission WPA2 Personal is far superior to WPA Personal because the encryption of data is upgraded with the Advanced Encryption Standard AES WPA Enterprise and WPA2 Enterprise is ideal for businesses that have existing security infrastructures in place Management and security implementation can now be centralized on a server participating on the network Utilizing 802 1x with a RADIUS Remote Authentication Dial in User Service server a network administrator can define a list of authorized users who can access the wireless LAN When attempting to access a wireless LAN with either WPA Enterprise or WPA2 Enterprise configured the new client will be challenged with a username and password If the new client is authorized by the administration and enters the correct username and password then access is granted In a scenario where an employee leaves the company the network administrator can remove the employee from the authorized list and not have to worry about the network being compromised by a former employee WPA2 Enterprise is far superior to WPA Enterprise because the encryp
38. g displays system and network messages including a time stamp and message type D Link DWL 2700AP User Manual 47 System Log Settings D Link 802 11G Outdoor Wireless AP Bridge Home Tool Configuration System Bi Logout GET DWL 27004P H B Basic Settings H Advanced Settings Log Settings Ae Status gt Device Information Log Server IP address A Indication ne Client Information Cea Tipe gele lie al B WDS Information Wireless Activity HA Stats H e wd i Ef Log Notice gt View Log gt Log Settings SMTP Settings SMTP CI Enable SMTP Server IP address SMTP Sender SMTP Recipient Log Settings Log Server IP Enter the IP address of the server you would like to send the Address DWL 2700APs log to Log Type Check the box for the type of activity you want to log There are three types System Wireless and Notice SMTP Settings SMTP Check the box to enable SMTP SMTP Server IP Enter the IP address of the SMTP server Address SMTP Sender Enter the e mail address of the SMTP sender SMTP Recipient Enter the e mail address of the SMTP recipient D Link DWL 2700AP User Manual 48 D Link S Home Tool e 2 DVYL 2700AP e ker Basic Settings Io ke Advanced Settings a p Status Device Information Indication Client Information WDS Information d gt Stats Cie Log View Log Log Settings Limit Administrator IP
39. ir or replace the defective Hardware the actual price paid by the original purchaser for the defective Hardware will be refunded by D Link upon return to D Link of the defective Hardware All Hardware or part thereof that is replaced by D Link or for which the purchase price is refunded shall become the property of D Link upon replacement or refund Limited Software Warranty D Link warrants that the software portion of the product Software will substantially conform to D Link s then current functional specifications for the Software as set forth in the applicable documentation from the date of original retail purchase of the Software for a period of ninety 90 days Software Warranty Period provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation D Link further warrants that during the Software Warranty Period the magnetic media on which D Link delivers the Software will be free of physical defects The customer s sole and exclusive remedy and the entire liability of D Link and its suppliers under this Limited Warranty will be at D Link s option to replace the non conforming Software or defective media with software that substantially conforms to D Link s functional specifications for the Software or to refund the portion of the actual purchase price paid that is attributable to the Software D Link DWL 2700AP User Manual 65 Except as otherwise agreed b
40. is recommended that you use an Ethernet connection to configure the DWL 2700AP 1 The computer used to configure the DWL 2700AP cannot access the Configuration menu E Check that the Ethernet LED on the DWL 2700AP is ON If the LED is not ON check that the cable for the Ethernet connection is securely inserted m Check that the Ethernet Adapter is working properly Please see item 3 Check that the drivers for the network adapters are installed properly in this Troubleshooting section to check that the drivers are loaded properly m Check that the IP address is in the same range and subnet as the DWL 2700AP Please see Checking the IP Address in Windows XP in the Networking Basics section of this manual Note The IP address of the DWL 2700AP is 192 168 0 50 All the computers on the network must have a unique IP address in the same range e g 192 168 0 x Any computers that have identical IP addresses will not be visible on the network They must all have the same subnet mask e g 255 255 255 0 m Do a Ping test to make sure that the DWL 2700AP is responding Go to Start gt Run gt Type Command gt Type ping 192 168 0 50 A successful ping will show four replies Note If you have changed the default IP address make sure to ping the correct IP address assigned to the DWL 2700AP e F WINDOWS System32 cmd exe Microsoft Windows XP Version 5 1 26001 lt C Copyright 1985 2001 Microsoft Corp F NDocuments and Settings lab3 gt ping 1
41. less AP Bridge Home Tool Configuration lt gt System DB Logout Help DAL 2700AP te e Basic Settings bee Wireless Band a g Advanced Settings Frequency o eA Performance im id Grouping F Multi SSID Data Rate E DHCP Server Es Filters B Status DTIM 1 255 Fragment Length 256 2346 346 RTS Interval 256 2346 346 Transmit Power Full Radio On v VM Enable v Channel Beacon Interval 20 1000 Wireless B G Mode Mixed e Antenna Diversity Diversity Wireless Band IEEE 802 119 Frequency The frequency reflects the choice of the wireless channel When IEEE 802 11g is chosen the frequency is 2 437GHz for channel 6 Channel The default channel for IEEE 802 119 is 6 Data Rate The Data Rates are Auto 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps Beacon Interval Beacons are packets sent by an access point to synchronize a network Specify a beacon interval value The default 100 is recommended D Link DWL 2700AP User Manual 33 DTIM Fragment Length RTS Length Radio WMM Wireless B G Antenna Diversity Delivery Traffic Indication Message Select a setting between 1 and 255 1 is the default setting DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages The fragmentation threshold which is specified in bytes deter
42. m RS Logout KA Help Wireless Band Mode wos Wireless Network Name SSID SSID Broadcast Enable wl 11 24126Hz Channel Auto Channel Scan WDS Remote AP MAC Address dl 2 laf Val e el lz el Site Survey Type CH Signal BSSID Security z Authentication Open System Key Settings Encryption Enable Key Size O Disable HEX vw First v 64Bits v Key Type Valid Key First Key Second Key Third Key Fourth Key Select Disabled or Enabled Disabled is selected here Select HEX or ASCII Select 64 bit 128 bit or 152 bits Select the 1st through the 4th key to be the active key Input up to four keys for eneryption You will select one of these keys in the valid key field Hexadecimal digits consist of the numbers 0 9 and the letters A F ASCII American Standard Code for Information Interchange is a code for representing English letters as numbers 0 127 D Link DWL 2700AP User Manual 29 WPA WPA2 Personal Encryption 2 s y D Link 802 11G Outdoor Wireless AP Bridge Home X Tool Configuration v gt System A Logout Help DAL 2700AP le Ze Basic Settings SE Wireless Band gt LAN H E Advanced Settings Mode Behe Wireless Network Name SSID dlink SSID Broadcast Enable Channel 1 M 2412GHz Auto Channel Scan WDS Remote AP MAC Address UP A je Jo Ja Site Sur
43. me IP address range as the access point and gateway Since the DWL 2700AP has an IP address of 192 168 0 50 wireless adapters must have an IP address in the same range e g 192 168 0 x Each device must have a unique IP address no two devices may have the same IP address The subnet mask must be the same for all the computers on the network To check the IP address assigned to the wireless adapter double click on the Local Area Connection icon in the taskbar gt select the Support tab and the IP address will be displayed Please refer to Checking the IP Address in the Networking Basics section of this manual E Ifitis necessary to assign a Static IP Address to the wireless adapter please refer to the appropriate section in Networking Basics If you are entering a DNS Server address you must also enter the Default Gateway Address Remember that if you have a DHCP capable router you will not need to assign a static IP address See Networking Basics Assigning a Static IP Address D Link DWL 2700AP User Manual 60 3 What variables may cause my wireless products to lose reception D Link products let you access your network from virtually anywhere you want However the positioning of the products within your environment will affect the wireless range Please refer to Installation Considerations in the Wireless Basics section of this manual for further information about the most advantageous placement of your D Link wireless products 4
44. mines whether packets will be fragmented Packets exceeding the 2346 byte setting will be fragmented before transmission 2346 is the default setting This value should remain at its default setting of 2346 If you encounter inconsistent data flow only minor modifications to the value range between 256 and 2346 are recommended Select ON or OFF Wi Fi Multimedia Improves the user experience for audio video and voice applications over a Wi Fi network This feature is enabled by default uncheck to disable Select Mixed for both 802 11b and 802 119 11b for 802 11b only or 11g for 802 119 only Select Diversity to allow the DWL 2700AP to automatically switch to the antenna with the better RSSI value Selecting Left Antenna will not allow the DWL 2700AP to switch antenna and the radio will use the left antenna facing the AP to transmit and receive packets Selecting Right Antenna will not allow the DWL 2700AP to switch antenna and the radio will only use the right antenna facing the AP to transmit and receive packets Maximum wireless signal rate derived from IEEE Standard 802 11g specifications Actual data throughput will vary Network conditions and environmental factors including volume of network traffic building materials and construction and network overhead lower actual data throughput rate Environmental factors may adversely affect wireless signal range D Link DWL 2700AP User Manual 34 AP Grouping Settings D
45. mputer D Link DWL 2700AP User Manual 12 Connecting to a Power over Ethernet Network pies DWL 2700AP Step 3 P DATA OUT LAN 1 PoE DATA IN Router or Switch Computer Straight Through Cable Crossover Cable Step 1 Connect one end of an Ethernet cable included with your package to the LAN port on the DWL 2700AP and the other end of the Ethernet cable to the port labeled P DATA OUT on the PoE base unit Step 2 Connect another Ethernet cable from the DATA IN port on the PoE base unit to your router switch or to a PC Step 3 Attach the power adapter to the connector on the PoE base unit Attach the power cord to the power adapter and into an electrical outlet D Link DWL 2700AP User Manual 13 Configuration This section will show you how to configure your D Link wireless access point using the web based configuration utility If you would like to use the AP Manager II software please refer to the documentation located on the D Link CD Web based Gonfiguration Utility To configure the DWL 2700AP use a computer which is connected to the DWL 2700AP with an Ethernet cable see the Network Layout diagram First disable the Access the Internet using a proxy server function To disable this function go to Control Panel gt Internet Options gt Connections gt LAN Settings and uncheck the enable box Start your web browser program and type the IP address of the DWL 2700AP in the address field ht
46. ncryption VLANID Delete Enable Multi SSID Check to enable Multi SSID Enable VLAN State Check to enable VLANS Band IEEE802 11g Index Select the Index you want to configure Primary or Multi SSID 1 through Multi SSID 7 Primary SSID and security cannot be configured here as those values follow the settings configured on the Home gt Basic Settings gt Wireless page SSID Service Set Identifier SSID is the unique name designated for the Index being configured D Link DWL 2700AP User Manual 36 SSID Broadcast Security Enabled by default disabling SSID Broadcast will make the SSID invisible Select Enable or Disable The Security options available are Open System Shared Key WPA Personal WPA2 Personal or WPA Auto Personal Note Security Setting Limit When the Primary SSID is set to use one key index for WEP you can use the 3 other key indexes for Guest SSIDs If the Primary SSID is set to WPA WPA2 Personal or WPA Auto Personal you can only use WEP key index 1 and 4 for Guest SSIDs Key Type Key Size Key Cipher Type Group Key Update Interval PassPhrase Select HEX or ASCII Only when Open System or Shared Key Security is selected Select 64 bit 128 bit or 152 bit Only when Open System or Shared Key is selected for Security Select from 1 of 4 Keys to be the active key Only when Open System or Shared Key is selected for Security When using WPA Personal
47. ndard to provide a wireless data rate of up to 11Mbps that means you can migrate your system to the 802 11g standard on your own schedule without sacrificing connectivity m Better security with WPA The DWL 2700AP can securely connect wireless clients on the network using WPA Wi Fi Protected Access providing a much higher level of security for your data and communications than has previously been available E AP Manager Il Management Software The real time display of topology and AP s information makes network configuration and management quick and simple SNMP for Management The DWL 2700AP is not just fast but it also supports SNMP v 3 for a better network management Superior wireless AP manager II software is bundled with the DWL 2700AP for network configuration and firmware upgrade Systems administrators can also setup the DWL 2700AP easily with the Web based configuration A D Link D View module will be downloadable for network administration and real time network traffic monitoring with D Link D View software Utilizes OFDM technology Orthogonal Frequency Division Multiplexing m Operates in the 2 4GHz frequency range for an 802 11b and 802 11g network m Web based interface for managing and configuring Maximum wireless signal rate derived from IEEE Standard 802 11g specifications Actual data throughput will vary Network conditions and environmental factors including volume of network traffic building materials and const
48. ole antennas with 5dBi gain Receiver Sensitivity For 802 11b e 1Mbps 92dBm e 2Mbps 89dBm e 5 5Mbps 88dBm e 11Mbps 83dBm For 802 11g e 1Mbps 92dBm e 2Mbps 89dBm e 5 5Mbps 88dBm e 6Mbps 87dBm e 9Mbps 86dBm e 11Mbps 85dBm e 12Mbps 88dBm e 18Mbps 83dBm e 24Mbps 80dBm e 36Mbps 76dBm e 48Mbps 71dBm e 54Mbps 66dBm Transmit Output Power For 802 11b e 100mW 20dBm e 50mW 17dBm e 30mW 15dBm e 20mW 13dBm e 10mW 10dBm 5mW 7dBm e 1mW OdBm For 802 11g e 200mW 23dBm e 63mW 18dBm e 30mW 15dBm e 20mW 13dBm e 10mW 10dBm 5mW 7dBm e 1mW OdBm Wireless Operating Range 802 11g Full power with 5dBi gain diversity dipole antenna Indoor e 98ft 30m 54Mbps e 112ft 34m amp 48Mbps e 128ft 39m 36Mbps e 154ft 47m 24Mbps e 184ft 56m amp 18Mbps e 217ft 66m 12Mbps e 259ft 79m 9Mbps e 325ft 99m 6Mbps 62 Outdoor e 367ft 112m 54Mbps e 820ft 250m 18Mbps e 1 640ft 500m amp 6Mbps LEDs e Power e 10 100M e RSSI level e 802 11b g Operating Voltage e 48VDC 10 for PoE Current Consumption e Max 8 5W without heater e Max 28 5W with heater Temperature e Operating 40 F to 140 F 40 C to 60 C e Storing 4 F to 149 F 40 C to 65 C Humidity e Operating 10 90 non condensing e Storing 5 95 non condensing Certifications e FCC Part 15 e CSA international Dimensions e L 10 93 inches
49. quency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communication However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures D Link DWL 2700AP User Manual 68 e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation IMPORTANT NOTICE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20
50. r Configuration in order for changes to take effect D Link DWL 2700AP User Manual 15 Wireless Modes AP Mode Authentication Available Access Point Open System Shared Key Open System Shared Key 802 1x WPA Enterprise WPA Personal WPA2 Enterprise WPA2 Personal WPA Auto Enterprise WPA Auto Personal WDS with AP Open System Shared Key Open System Shared Key WPA Personal WPA2 Personal WPA Auto Personal WDS Open System Shared Key Open System Shared Key WPA2 Personal WPA Personal WPA Auto Personal D Link DWL 2700AP User Manual 16 Wireless Settings Access Point Mode D Link 802 11G Outdoor Wireless AP Bridge Home X Tool Configuration v D System Bi Logout W W Help DVWL 27004P a a p Basic Settings Ska Wireless Wireless Band IEEE802 11 i gt LAN Advanced Settings Mode Access Paint v EES Wireless Network Name SSID dlink SSID Broadcast Enable wv Channel 1 2 412 GHz Auto Channel Scan Authentication Open System vi Key Settings Open System Shared Key Encryption Disable open system Shared Key Key Type WPA Enterprise WPA Personal Valid Key rst WPA2 Enterprise WPA2 Personal First Key Second Key nenn d WPA Auto Personal 802 1x Third Key Fourth Key kesesesess si Apply la MEG Wireless Band IEEE 802 119 Mode Access Point is selected from the drop down menu SSID Service Set Identifier SSID is
51. ruction and network overhead lower actual data throughput rate Environmental factors may adversely affect wireless signal range D Link DWL 2700AP User Manual 8 Wireless Basics D Link wireless products are based on industry standards to provide easy to use and compatible high speed wireless connectivity within your home business or public access wireless networks D Link wireless products will allow you to access the data you want when and where you want it You will be able to enjoy the freedom that wireless networking brings A Wireless Local Area Network WLAN is a computer network that transmits and receives data with radio signals instead of wires WLANs are used increasingly in both home and office environments and public areas such as airports coffee shops and universities Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users Wireless users can use the same applications they use on a wired network Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards People use WLAN technology for many different purposes Mobility Productivity increases when people have access to data in any location within the operating range of the WLAN Management decisions based on real time information can significantly improve
52. s AP Bridge e D Link 5 System Bi Logout Help amp Home X Tool Configuration v DVYL 2700AP ed B Basic Settings ce WB Advanced Settings Temperature Indication Ae Status Device Information gt Indication ALS IER Client Information WDS Information A Stats tz Log 46 C 114 F Temperature Indication This window displays the current operating temperature of the DWL 2700AP D Link DWL 2700AP User Manual 43 Client Information D Link 802 11G Outdoor Wireless AP Bridge Home Tool Configuration gt System BS ona ET DAL 2700AP En le Basic Settings a WB Advanced Settings Client information Station association with 11B G 0 I f r Status ED Mac Band Authentication Active signal PSM Device Information gt Indication gt Client Information er WDS Information HA Stats tz Log Client Information The Client Information page provides information about the wireless clients connected to the DWL 2700AP The following information is available for each client communicating with the DWL 2700AP MAG Displays the MAC address of the client Band Displays the wireless band the client is connected on Authentication Displays the type of authentication being used Signal Displays the strength of the clients signal Power Saving Displays the status of the power saving feature Mode D Link DWL 2700AP User Manual
53. ss network or to establish a new wireless network D Link DWL 2700AP User Manual 27 SSID Broadcast Channel Auto Channel Scan Remote AP MAC Address Scan Authentication Enable or Disable SSID broadcast Enabling this feature broadcasts the SSID across the network 6 is the default channel for IEEE 802 11g All devices on the network must share the same channel Note The wireless adapters will automatically scan and match the wireless setting This option is unavailable in WDS Enter the MAC addresses of the APs in your network that will serve as bridges to wirelessly connect multiple networks Click Scan to view available APs in your network that will serve as bridges Select Open System to communicate the key across the network Select Shared Key to limit communication to only those devices that share the same WEP settings Select Open System Shared Key to allow either form of data encryption Select WPA Personal WPA2 Personal or WPA Auto Personal to secure your network using a password and dynamic key changes No RADIUS server required D Link DWL 2700AP User Manual 28 D Link Tool f Home DAL 2700AP a g Basic Settings gt Wireless gt LAN Status Encryption Key Type Key Size Valid Key First through Fourth keys Advanced Settings WEP Encryption 802 11G Outdoor Wireless AP Bridge Configuration v Syste
54. subnet mask gateway and DNS settings are correctly entered for the network If you are using 2 4GHz cordless phones X 10 equipment or other home security systems ceiling fans and lights your wireless connection will degrade dramatically or drop altogether Try changing the channel on your DWL 2700AP and on all the devices in your network to avoid interference Keep your product away at least 3 6 feet from electrical devices that generate RF noise like microwaves monitors electric motors etc D Link DWL 2700AP User Manual 61 Technical Specifications Standards e IEEE 802 11b e IEEE 802 119 e IEEE 802 3 e IEEE 802 3u e IEEE 802 3x Network Management e Web Browser interface HTTP e AP Manager II e SNMP Support D View Module Private MIB e Command Line Interface Telnet Data Rate For 802 11b e 11 5 5 2 and 1Mbps For 802 119 e 54 48 36 24 18 12 9 and 6Mbps Security e WPA Personal e WPA Enterprise e WPA2 Personal e WPA2 Enterprise e 64 128 152 bit WEP e SSID Broadcast Disable e MAC Address Access Control List Wireless Frequency Range e 2 4GHz to 2 4835GHz Radio and Modulation Type For 802 11b DSSS e DBPSK 1Mbps e DQPSK 2Mbps e CCK 5 5 and 11Mbps For 802 119 OFDM e BPSK 6 and 9Mbps e QPSK 12 and 18Mbps e 16QAM 24 and 36Mbps e 64QAM 48 and 54Mbps DSSS e DBPSK 1Mbps e DQPSK 2Mbps e CCK 5 5 and 11Mbps D Link DWL 2700AP User Manual Antenna Type e Monop
55. tal walls with insulation water fish tanks mirrors file cabinets brick and concrete will degrade your wireless signal 4 Keep your product away at least 3 6 feet or 1 2 meters from electrical devices or appliances that generate RF noise 5 If you are using 2 4GHz cordless phones or X 10 wireless products such as ceiling fans lights and home security systems your wireless connection may degrade dramatically or drop completely Make sure your 2 4GHz phone base is as far away from your wireless devices as possible The base transmits a signal even if the phone in not in use D Link DWL 2700AP User Manual 11 Getting Started DWL 2700AP Ethernet Cable Inline Power Injector included Hub Switch or Router You will need broadband Internet access Consult with your Cable or DSL provider for proper installation of the modem Connect the Cable or DSL modem to a Router See the printed Hardware Installation Guide included with your router Connect the Ethernet Broadband Router to the PoE base unit See the printed Hardware Installation Guide included with the DWL 2700AP Connect the DWL 2700AP to the PoE base unit See the printed Hardware Installation Guide included with the DWL 2700AP If you are connecting a desktop computer to your network install a wireless PCI adapter into an available PCI slot on your desktop computer Install the drivers for your wireless Cardbus adapter into a laptop co
56. the name designated for a specific wireless local area network WLAN The SSID factory default setting is dlink The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network SSID Broadcast Enable or Disable SSID broadcast Enabling this feature broadcasts the SSID across the network Channel Auto Channel Scan is selected by default All devices on the network must share the same channel Radio Frequency The radio frequency will vary depending on the wireless channel that is chosen The frequency in channel 6 is 2 437GHz D Link DWL 2700AP User Manual 17 Auto Channel Scan Authentication Select Enable or Disable Enable this feature to auto select the channel for best wireless performance Select Open System to communicate the key across the network Select Shared Key to limit communication to only those devices that share the same WEP settings Select Open System Shared Key to allow either form of data encryption Select WPA Enterprise to secure your network with the inclusion of a RADIUS server Select WPA Personal to secure your network using a password and dynamic key changes No RADIUS server required Select WPA2 Enterprise to secure your network with the inclusion of a RADIUS server and upgrade the encryption of data with the Advanced Encryption Standard AES Select WPA2 Personal to secure your network using a password and dynamic key changes No RA
57. tion of data is upgraded with the Advanced Encryption Standard AES 802 1x Authentication which is a first line of defense against intrusion In the authentication process the Authentication Server verifies the identity of the client attempting to connect to the network Unfamiliar clients would be denied access EAP Extensible Authentication Protocol is available through the Windows XP Operating System You will need to use the same type of EAP protocol on all the devices in your network when using the 802 1x feature Maximum wireless signal rate derived from IEEE Standard 802 11g specifications Actual data throughput will vary Network conditions and environmental factors including volume of network traffic building materials and construction and network overhead lower actual data throughput rate Environmental factors may adversely affect wireless signal range D Link DWL 2700AP User Manual 7 Features m 3 Different Operation modes Capable of operating in one of three different operation modes to meet your wireless networking requirements Access Point WDS with AP or WDS H Easy Installation with PoE Power over Ethernet Faster wireless networking speeds up to 54Mbps m Compatible with 802 11b and 802 119 Devices that is fully compatible with the IEEE 802 11b and 802 119 standards the DWL 2700AP can connect with existing 802 1 1b or 802 11g compliant wireless network adapter cards Compatible with the 802 11b sta
58. tp 192 168 0 50 and press Enter Make sure that the IP addresses of the DWL 2700AP and your computer are in the same subnet Microsoft Internet Explorer File Edit View Favorites Tools Help Q sxx amp 2 a L po search ze Address http 192 168 0 50 After the connection is established you will see the user identification window as shown Note If you have changed the default IP address assigned to the DWL 2700AP make sure to enter the correct IP address e Type admin in the User Name field Leave the Password field blank e Click OK Connect to 192 168 0 50 DWL 27004P User name admin Password Remember my password Note If you have changed the password make sure to enter the correct password D Link DWL 2700AP User Manual 14 Save and Activate D Link 802 116 Outdoor Wireless AP Bridge Home Tool Configuration v gt Syste DB Logout Mm Help pvyL 27008P Basic Settings Advanced Settings Model Name DWL 2700AP H E Status System Time Not Available Up Time 0 day 0 04 47 Firmware Version 3 10 IP address 192 168 0 50 Clicking Configuration gt Save and Activate will save and activate all changes made to the configuration and reboot the system Clicking Discard Changes will discard all changes made to the configuration Click the Apply button to save changes made to the current page Apply Please note that you still must select Save and Activate unde
59. ts within the specified range of this device you will be able to transfer large files quickly or even watch a movie in MPEG format over your network without noticeable delays This technology works by transmitting high speed digital data over a radio wave utilizing OFDM Orthogonal Frequency Division Multiplexing technology OFDM works by splitting the radio signal into multiple smaller sub signals that are then transmitted simultaneously at different frequencies to the receiver OFDM reduces the amount of crosstalk interference in signal transmissions The D Link DWL 2700AP will automatically sense the best possible connection speed to ensure the greatest speed and range possible The DWL 2700AP offers the most advanced network security features available today including WPA and WPA2 In addition to its compatibility with 802 11g devices the DWL 2700AP is compatible with 802 1 1b devices This means that if you have an existing 802 11b network or a network with a mixture of 802 11g and 802 11b the devices in that network will be compatible with the DWL 2700AP Maximum wireless signal rate derived from IEEE Standard 802 11g specifications Actual data throughput will vary Network conditions and environmental factors including volume of network traffic building materials and construction and network overhead lower actual data throughput rate Environmental factors may adversely affect wireless signal range D Link DWL 2700AP User Manual
60. u wish to assign a static IP address to the DWL 2700AP IP Address The default IP address is 192 168 0 50 Assign a static IP address that is within the IP address range of your network Subnet Mask Enter the subnet mask All devices in the network must share the same subnet mask Default Gateway Enter the IP address of the gateway in your network If there isn t a gateway in your network please enter an IP address within the range of your network DNS 1 Enter your primary DNS IP address DNS 2 Enter your secondary DNS IP address D Link DWL 2700AP User Manual EN Dynamic D Link 802 11G Outdoor Wireless AP Bridge Home X Tool Configuration System P Logout Help DAL 2700AP Ger Basic Settings vn Get IP From Dynamic DHCP v ko Advanced Settings IP address f Status Subnet Mask LJ Default Gateway DNS 1 DNS 2 Get IP From Dynamic DHCP is chosen here Choose Dynamic IP Address to obtain an IP Address automatically from a DHCP server in your network IP Address This field is unavailable when DHCP is selected Subnet Mask This field is unavailable when DHCP is selected Default Gateway This field is unavailable when DHCP is selected DNS 1 This field is unavailable when DHCP is selected DNS 2 This field is unavailable when DHCP is selected D Link DWL 2700AP User Manual Advanced Settings Performance D Link 802 11G Outdoor Wire
61. vey Type CH Signal BSSID Security Authentication WPA Personal PassPhrase Settings Cipher Type AES w Group Key Update Interval 1800 Sec Cipher Type When you select WPA Personal WPA2 Personal or WPA Auto Personal AES is selected as the Cipher Type Group Key Update Select the interval during which the group key will be valid The default Interval value of 1800 is recommended PassPhrase When you select WPA Personal WPA2 Personal or WPA Auto Personal please enter a PassPhrase in the corresponding field D Link DWL 2700AP User Manual 30 LAN Settings Static D Link 802 11G Outdoor Wireless AP Bridge Home Tool RB Configuration Bi Logout Help DAL 2700AP o Ge Basic Settings gt Wireless gt LAN E f Advanced Settings IP address 192 168 0 50 D B ss Subnet Mask 255 255 255 0 Default Gateway 0 0 0 0 DNS 1 DNS 2 Get IP Fram Static Manual LAN is short for Local Area Network This is considered your internal network These are the IP settings of the LAN interface for the DWL 2700AP These settings may be referred to as private settings You may change the LAN IP address if needed The LAN IP address is private to your internal network and cannot be seen on the Internet Get IP From Static Manual is chosen here Choose this option if you do not have a DHCP server in your network or if yo
62. y that is not contemplated in the documentation for the product or if the model or serial number has been altered tampered with defaced or removed Initial installation installation and removal of the product for repair and shipping costs Operational adjustments covered in the operating manual for the product and normal maintenance Damage that occurs in shipment due to act of God failures due to power surge and cosmetic damage Any hardware software firmware or other products or services provided by anyone other than D Link and Products that have been purchased from inventory clearance or liquidation sales or other sales in which D Link the sellers or the liquidators expressly disclaim their warranty obligation pertaining to the product While necessary maintenance or repairs on your Product can be performed by any company we recommend that you use only an Authorized D Link Service Office Improper or incorrectly performed maintenance or repair voids this Limited Warranty Disclaimer of Other Warranties EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN THE PRODUCT IS PROVIDED AS IS WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER INCLUDING WITHOUT LIMITATION ANY WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIO
63. y DLink in writing the replacement Software is provided only to the original licensee and is subject to the terms and conditions of the license granted by D Link for the Software Replacement Software will be warranted for the remainder of the original Warranty Period and is subject to the same limitations and exclusions If a material non conformance is incapable of correction or if D Link determines in its sole discretion that it is not practical to replace the non conforming Software the price paid by the original licensee for the non conforming Software will be refunded by D Link provided that the non conforming Software and all copies thereof is first returned to D Link The license granted respecting any Software for which a refund is given automatically terminates Non Applicability of Warranty The Limited Warranty provided hereunder for Hardware and Software portions of D Link s products will not be applied to and does not cover any refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D Link the sellers or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case the product is being sold As Is without any warranty whatsoever including without limitation the Limited Warranty as described herein notwithstanding anything stated herein to the contrary Submitting A Claim The customer shall return the product to the

D-LINK DWL-2700AP Manual

Contents

Download Pdf Manuals

Related Search

Related Contents